1
|
Dai Y, Wang W, Xu Y, Li Y, Liu T. Experimental study on the influence of turbulence on hail impacts. Sci Rep 2024; 14:18317. [PMID: 39112656 PMCID: PMC11306780 DOI: 10.1038/s41598-024-69234-5] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/24/2024] [Accepted: 08/01/2024] [Indexed: 08/11/2024] Open
Abstract
Hailstorms, characterized by their intensity, are often accompanied by strong winds and heavy rain, posing significant destructive potential. Data indicate that the economic losses caused by hail to buildings, particularly solar panels, have been increasing annually. However, research on the hail resistance of photovoltaic panels has predominantly focused on the isolated effects of hail impacts and wind loads, neglecting the coupling effects between wind and hail. In this study, a device was designed to couple both wind and hail. The effects of turbulence, hail size, and velocity on hail impact behavior were systematically studied and quantified. A predictive formula for the peak load of hail impact on structures was established. The results indicate that the impact of turbulence on hail is significant. When turbulence intensity varies with hail velocity, hail impact force increases as turbulence decreases and hail velocity increases. When both turbulence and hail diameter vary, the impact force of smaller hailstones shows less variation with increasing turbulence. According to variance analysis, hail velocity is the most significant factor affecting hail impact, followed by hail diameter and finally turbulence. The regression equation is given by F = - 0.624 I u + 5116.25 D + 7.85 V hail - 259.709 , where F represents the peak impact force in Newtons (N), I u denotes the turbulence intensity, D is the hail diameter in meters (m), and V hail is the hail velocity in meters per second (m/s).
Collapse
Affiliation(s)
- Yimin Dai
- Hunan Provincial Key Laboratory of Structural Wind and Vibration Control, Xiangtan, 411201, China.
- School of Civil Engineering, Hunan University of Science and Technology, Xiangtan, 411201, China.
| | - Wei Wang
- Hunan Provincial Key Laboratory of Structural Wind and Vibration Control, Xiangtan, 411201, China
- School of Civil Engineering, Hunan University of Science and Technology, Xiangtan, 411201, China
| | - Ying Xu
- Hunan Provincial Key Laboratory of Structural Wind and Vibration Control, Xiangtan, 411201, China
- School of Civil Engineering, Hunan University of Science and Technology, Xiangtan, 411201, China
| | - Yixin Li
- Hunan Provincial Key Laboratory of Structural Wind and Vibration Control, Xiangtan, 411201, China
- School of Civil Engineering, Hunan University of Science and Technology, Xiangtan, 411201, China
| | - Taiting Liu
- Hunan Provincial Key Laboratory of Structural Wind and Vibration Control, Xiangtan, 411201, China
- School of Civil Engineering, Hunan University of Science and Technology, Xiangtan, 411201, China
| |
Collapse
|
2
|
Surface Hierarchy: Macroscopic and Microscopic Design Elements for Improved Sliding on Ice. LUBRICANTS 2021. [DOI: 10.3390/lubricants9100103] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
Frictional interaction with a surface will depend on the features and topography within the contact zone. Describing this interaction is particularly complex when considering ice friction, which needs to look at both the macroscopic and microscopic levels. Since Leonardo da Vinci shared his findings that roughness increases friction, emphasis has been placed on measuring surface coarseness, neglecting the contact area. Here, a profilometer was used to measure the contact area at different slicing depths and identify contact points. Metal blocks were polished to a curved surface to reduce the contact area; further reduced by milling 400 µm grooves or laser-micromachining grooves with widths of 50 µm, 100 µm, and 150 µm. Sliding speed was measured on an inclined ice track. Asperities from pileup reduced sliding speed, but a smaller contact area from grooves and a curved sliding surface increased sliding speed. An analysis of sliding speed versus contact area from incremental slicing depths showed that a larger asperity contact surface pointed to faster sliding, but an increase in the polished surface area reduced sliding. As such, analysis of the surface at different length scales has revealed different design elements—asperities, grooves, curved zones—to alter the sliding speed on ice.
Collapse
|