Improvement of Cr-Co-Mo Membrane Surface Used as Barrier for Bone Regeneration through UV Photofunctionalization: An In Vitro Study

Effect of ultraviolet irradiation treatment on shear bond strength between polymethyl methacrylate and cobalt-chromium-molybdenum alloy

We aimed to elucidate the effects of ultraviolet (UV) irradiation on the shear bond strength (SBS) between heat-cured polymethyl methacrylate (PMMA) and a Co-Cr-Mo alloy. Disk-shaped Co-Cr-Mo alloy prepared by casting were subjected to different UV treatment times (0, 15, and 30 min). To determine the effect of UV treatment on surface properties of the alloy, surface roughness, wettability, and chemical compositions were analyzed. To evaluate the SBS, cylindrical PMMA was bonded to the UV-treated alloy, and subsequently subjected to the SBS test after 24 h of storage at room temperature or following 10,000 thermal cycles (n=10/group). After the UV treatment, the surface roughness remained unchanged, but oxidation resulted in the surface exhibiting greater hydrophilic characteristics. The UV-treated group showed significantly higher SBS values than those of the non-treated group (p<0.001). These results suggested that UV treatment-mediated oxidation improved the bond strength between PMMA and Co-Cr-Mo alloy.

Improvement in the chemical structure and biological activity of surface titanium after exposure to UVC light

Ultraviolet (UV) irradiation has been proposed as a method to reverse the aging process of titanium. However, the intensity, exposure time and wavelength that provide the best results have not yet been determined. The objective of this study was to evaluate the effects of photocatalysis by ultraviolet C light on the time-dependent aging of titanium and to analyze the irradiated titanium for changes in structure and in vitro biological activity, with regard to different exposure times. A titanium photofunctionalization device was developed with characteristics different from those on the market. The sample was composed of titanium disks irradiated for different times of exposure to ultraviolet C light (0, 15, 30 and 60 min). The disks were tested for surface wettability (water contact angle), topography (scanning electron microscopy-SEM) and chemical composition (X-ray photoelectron spectroscopy), and effects on cell adhesion (cell culture and SEM) and cell viability by sulforhodamine B (SRB). Ultraviolet C treatment caused changes in titanium surface characteristics, such as increased wettability and removal of hydrocarbons from the surface after 15 min of exposure in the chamber developed. The biological characteristics of the material also appear to have changed, with improved cell adhesion and viability. Photofunctionalization of titanium proved to be effective for the treatment of aged surfaces, with significant modifications in the surface chemical structure and biological activity of the material.

In vivo effect of UV-photofunctionalization of CoCrMo in processes of guided bone regeneration and tissue engineering

Photofunctionalization of implant materials with ultraviolet (UV) radiation have been subject of study in the last two decades, and previous research on CoCrMo discs have showed good results in terms of bioactivity and the findings of apatite-like crystals in vitro. In the current study, CoCrMo domes were photofunctionalized with UV radiation of 254 nm on their internal faces during 24 hr; they were implanted in rabbit tibia and remained for 3, 4, and 6 weeks. The potential to induce bone formation beneath the dome-shaped membranes was evaluated through morphometric, histologic, and density measurements; and the results were compared with those obtained under control untreated domes. Higher density values were observed for irradiated domes at 3 weeks, whereas higher volumes were obtained under photofunctionalized domes for longer periods (4 and 6 weeks). Histologically, woven bone was formed by endochondral ossification in all cases; differences in the architecture and size of the trabeculae and in the number of osteoblasts were noted between irradiated and non-irradiated samples. The UV radiation of 254 nm generated a larger bone volume fraction compared to that found in the absence of UVC radiation and induced an increase of density in the early stages of healing, leading to a better initial bone quality and improved osseointegration.

Effects of Ultraviolet Photoactivation on Osseointegration of Commercial Pure Titanium Dental Implant After 8 Weeks in a Rabbit Model

This study investigated whether a 6-Watt ultraviolet C-lamp was capable of producing photofunctionalization on commercial implants during a medium observation term of 8 weeks. A total of 20 implants were inserted in 5 New Zealand rabbits, with each animal receiving 2 implants per tibia (one photofunctionalized and one untreated), according to a previously established randomization sequence. All implants were inserted by a single surgeon following the manufacturer's instructions. Histological analysis was performed by an evaluator who was blinded to the treatment condition. After 8 weeks of healing, the 2 groups showed no statistically significant differences in terms of bone-to-implant contact. Compared to control implants, the photofunctionalized implants showed improved wettability and more homogenous results. Within the limits of the present study, the use of this 6-W ultraviolet C-lamp, for an irradiation time of 15 minutes at a distance of 15 cm, did not improve the percentages of bone-to-implant contact in rabbits at an osseointegration time of 8 weeks.