Sintering Behavior and Mechanical Properties of Mullite Fibers/Hydroxyapatite Ceramic

Microstructural Evaluation of the Mineralized Apical Barrier Induced by a Calcium Hydroxide Paste Containing Iodoform: A Case Report

INTRODUCTION

A 65-year-old man had nonsurgical retreatment using an iodoform and calcium hydroxide paste in a maxillary left canine with persistent apical periodontitis. An apical mineralized barrier (AMB) was observed 3-months postoperatively. Unfortunately, the tooth was extracted due to a cementum tear. This provided an opportunity to analyze the AMB histologically, as there is a lack of previous reports on its microstructure.

METHODS

After extraction and removal of the granulation tissue from the root surface, the canine was processed, and observed using micro-computed tomography (μCT) and light microscopy. Thereafter, the specimen was resin-embedded specimen was evaluated by scanning electron microscopy, micro-X-ray fluorescence spectroscopy and Raman spectroscopy to understand the mechanism and nature of the AMB formation during apical healing.

RESULTS

Nonsurgical retreatment was clinically successful based on the absence of clinical symptoms of apical periodontitis and the radiographic presence of an AMB. The AMB was opaque and could be readily differentiated from dentin under a light microscope. Micro-computed tomography analysis revealed that the AMB had the same mineral density as dentin. Scanning electron microscopy revealed that the AMB had two distinct layers based on the size of the calcified particles. Elemental mapping using micro-X-ray fluorescence spectroscopy showed that the localization of calcium and phosphorus differed between AMB and other areas of biomineralization. Raman spectral mapping revealed that the surface layer of the AMB consisted of collagen, calcium carbonate, and hydroxyapatite.

CONCLUSIONS

This study explored new analytical methods for elucidating the apical wound-healing process and the nature of the mineralized repair. The findings provided detailed information on the AMB highlighting a bilaminar structure with high calcium components higher on the inside and a brightness similar to cementum not dentin and the presence of hydroxyapatite.

The Effect of Bone Ash on the Physio-Chemical and Mechanical Properties of Clay Ceramic Bricks

Bone ash waste can be used to fabricate clay ceramic bricks, consequently managing their pollution of the environment. This is because bone ash (BA) and clay predominantly consist of calcium and alumina-silicate, respectively, which are components of clay ceramic brick (CCB) materials. This study aims to investigate the effect of bone ash and temperature on the physio-chemical and mechanical properties of CCB. Different percentages of bone ash (5%, 10%, 15%, and 20%) were added to clay and heat treated at temperatures of 100 °C, 300 °C, 600 °C, and 900 °C, and their compressive strengths were measured. Prior to the determination of their mechanical properties, the CCB chemical and phase compositions were characterized using FTIR spectroscopy and X-ray diffraction (XRD). The CCB microstructure was evaluated with scanning electron microscopy (SEM) and the compressive strength was tested. The results suggest that the addition of bone ash (10% and 15%) improves the compressive strength and water absorption properties after heat treatment of CCB at higher temperatures.

Effect of zirconia-mullite incorporated biphasic calcium phosphate/biopolymer composite scaffolds for bone tissue engineering

New bioactive scaffolds with improved mechanical properties, biocompatibility and providing structural support for bone tissue are being developed for use in the treatment of bone defects. In this study, we have synthesized bioactive scaffolds consisting of biphasic calcium phosphate (BCP) and zirconia-Mullite (2ZrO₂·[3Al₂O₃ ·2 SiO₂] (ZAS)) (BCPZAS) combined with polymers matrix of polycaprolactone (PCL)-alginate (Alg)-chitosan (Chi) (Chi/Alg-PCL) (BCPZAS@Chi/Alg-PCL). The composite material scaffolds were prepared by a blending technique. The microstructure, mechanical, bioactivity and in vitro biological properties with different ratios of BCP to ZAS of 1:0, 3:1, 1:1, 1:3 and 0:1 wt% in polymer matrix were analyzed. Microstructure analysis showed a successful incorporation of the BCPZAS particles with an even distribution of them within the polymer matrix. The mechanical properties were found to gradually decrease with increasing the ratio of ZAS particles in the scaffolds. The highest compressive strength was 42.96 ± 1.01MPa for the 3:1 wt% BCP to ZAS mixing. Bioactivity test, the BCPZAS@Chi/Alg-PCL composite could induce apatite formation in simulate body fluid (SBF). In-vitro experiment using UMR-106 osteoblast-like cells on BCPZAS@Chi/Alg-PCL composite scaffold showed that there is cell attachment to the scaffolds with proliferation. These experimental results demonstrate that the BCPZAS@Chi/Alg-PCL composite especially for the BCP:ZAS at 3:1 wt% could be utilized as a scaffold for bone tissue engineering applications.

Microstructure and Mechanical Properties of Titanium–Equine Bone Biocomposites

Microstructure and mechanical properties of Ti-6Al-4V/equine bone (EB) composites fabricated by ball milling and spark plasma sintering (SPS) have been investigated. Ti-6Al-4V/EB composites were successfully fabricated by a planetary ball-milling of spherical Ti6Al4V powder and natural EB powder and SPS at 1000 °C within 15 min under 50 MPa. EB was uniformly dispersed in the Ti6Al4V matrix owing to ball-milling, and beta phase transformation temperature of 1000 °C provided phase stability. The composites containing 0.5 wt.% EB exhibit Vickers hardness and elastic modulus of 540.6 HV and 130.5 GPa, respectively. The microstructures and mechanical properties of the composites were observed using scanning electron micrograph and nanoindentation.

Effect of Urchin-Like Mullite Whiskers on the High-Temperature Performance of Porous SiO₂-Based Ceramic Molds

Urchin-like mullite whiskers synthesized by the vapor–liquid–solid growth method were used to improve the high-temperature performance of porous gelcast SiO₂-based ceramic molds. Aluminum was used to facilitate the synthesis of polycrystal urchin-like mullite whiskers which acted as bridges between particles. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used to investigate the microstructures and phase compositions of the sintered ceramic samples, respectively. Urchin-like mullite whiskers with diameters of 0.2~1.0 µm and lengths of 1.0~8.0 µm were successfully synthesized in SiO₂-based ceramic. When 15 vol% Al was added, the high-temperature strength at 1200 °C was improved from 8.5 to 27.5 MPa, and the creep deformation was decreased to 0.56 mm. Meanwhile, a sintering shrinkage below 0.3% was obtained, and the de-coring rate was accelerated by 67% compared to that of the pure SiO₂-based ceramic. This method showed excellent high-temperature strength and high precision, having remarkable potential in the fabrication of hollow turbine blades.