Non Monotonous Effects of Noncovalently Functionalized Graphene Addition on the Structure and Sound Absorption Properties of Polyvinylpyrrolidone (1300 kDa) Electrospun Mats

Assessing the Sound and Heat Insulation Characteristics of Layered Nonwoven Composite Structures Composed of Meltblown and Recycled Thermo-Bonded Layers

Sound and heat insulation are among the most important concerns in modern life and nonwoven composite structures are highly effective in noise reduction and heat insulation. In this study, three layered nonwoven composite structures composed of a recycled polyester (r-Pet)-based thermo-bonded nonwoven outer layer and meltblown nonwovens from Polypropylene (PP) and Polybutylene terephthalate (PBT) as inner layers were formed to provide heat and sound insulation. Fiber fineness and cross-section of the thermo-bonded outer layer, fiber type (PP/PBT), areal weight (100/200 g/m2) and process conditions (calendared/non-calendared) of the meltblown inner layer were changed systematically and the influence of these independent variables on thickness, bulk density, air permeability, sound absorption coefficient and thermal resistance of composite structures were analyzed statistically by using Design Expert 13 software. Additionally, the results were compared with composite structures including an electrospun nanofiber web inner layer and with structures without an inner layer. It was concluded that comparable or even better sound absorption values were achieved with the developed nonwoven composites containing meltblown layers compared to nanofiber-included composites and the materials in previous studies.

A Polyvinylpyrrolidone Nanofibrous Sensor Doubly Decorated with Mesoporous Graphene to Selectively Detect Acetic Acid Vapors

An original approach has been proposed for designing a nanofibrous (NF) layer using UV-cured polyvinylpyrrolidone (PVP) as a matrix, incorporating mesoporous graphene carbon (MGC) nanopowder both inside and outside the fibers, creating a sandwich-like structure. This architecture is intended to selectively adsorb and detect acetic acid vapors, which are known to cause health issues in exposed workers. The nanocomposite MGC-PVP-NFs layer was fabricated through electrospinning deposition onto interdigitated microelectrodes (IDEs) and stabilized under UV-light irradiation. To enhance the adhesion of MGC onto the surface of the nanocomposite polymeric fibers, the layer was dipped in a suspension of polyethyleneimine (PEI) and MGC. The resulting structure demonstrated promising electrical and sensing properties, including rapid responses, high sensitivity, good linearity, reversibility, repeatability, and selectivity towards acetic acid vapors. Initial testing was conducted in a laboratory using a bench electrometer, followed by validation in a portable sensing device based on consumer electronic components (by ARDUINO®). This portable system was designed to provide a compact, cost-effective solution with high sensing capabilities. Under room temperature and ambient air conditions, both laboratory and portable tests exhibited favorable linear responses, with detection limits of 0.16 and 1 ppm, respectively.

Research Progress on Sound Absorption of Electrospun Fibrous Composite Materials

Noise is considered severe environmental pollutant that affects human health. Using sound absorption materials to reduce noise is a way to decrease the hazards of noise pollution. Micro/nanofibers have advantages in sound absorption due to their properties such as small diameter, large specific surface area, and high porosity. Electrospinning is a technology for producing micro/nanofibers, and this technology has attracted interest in the field of sound absorption. To broaden the applications of electrospun micro/nanofibers in acoustics, the present study of electrospun micro/nano fibrous materials for sound absorption is summarized. First, the factors affecting the micro/nanofibers' sound absorption properties in the process of electrospinning are presented. Through changing the materials, process parameters, and duration of electrospinning, the properties, morphologies, and thicknesses of electrospun micro/nanofibers can be controlled. Hence, the sound absorption characteristics of electrospun micro/nanofibers will be affected. Second, the studies on porous sound absorbers, combined with electrospun micro/nanofibers, are introduced. Then, the studies of electrospun micro/nanofibers in resonant sound absorption are concluded. Finally, the shortcomings of electrospun micro/nano fibrous sound absorption materials are discussed, and the future research is forecasted.

Shape-Memory Materials via Electrospinning: A Review

This review aims to point out the importance of the synergic effects of two relevant and appealing polymeric issues: electrospun fibers and shape-memory properties. The attention is focused specifically on the design and processing of electrospun polymeric fibers with shape-memory capabilities and their potential application fields. It is shown that this field needs to be explored more from both scientific and industrial points of view; however, very promising results have been obtained up to now in the biomedical field and also as sensors and actuators and in electronics.

Experimental/Numerical Acoustic Assessment of Aircraft Seat Headrests Based on Electrospun Mats

The work proposes a methodology for the assessment of the performances of Passive Noise Control (PNC) for passenger aircraft headrests with the aim of enhancing acoustic comfort. Two PNC improvements of headrests were designed to reduce the Sound Pressure Level (SPL) at the passengers’ ears in an aircraft cabin during flight; the first was based on the optimization of the headrest shape, whereas the second consisted of partially or fully covering the headrest surface with a new highly sound-absorbing nanofibrous textile. An experimental validation campaign was conducted in a semi-anechoic chamber. A dummy headrest was assembled in different configurations of shape and materials to assess the acoustic performances associated to each set up. In parallel, simulations based on the Boundary Element Method (BEM) were performed for each configuration and an acceptable correlation between experimental and numerical results was obtained. Based on these findings, general guidelines were proposed for the acoustical design of advanced headrests.

Features of Structure and Properties of pнeмa-gr-pvp Block Copolymers, Obtained in the Presence of Fe2

This paper presents the research results of the copolymer structure and properties of 2-hydroxyethylmethacrylate (HEMA) with polyvinylpyrrolidone (PVP) and their hydrogels, obtained by block polymerization in the presence of iron sulfate (II). By the methods of chemical analysis, IR spectroscopy, Thermogravimetric (TG) and Differential Thermal Analysis (DTA), the course of grafted copolymerization of HEMA on PVP with the formation of a cross-linked copolymer was confirmed. The results received by scanning electron microscopy showed that due to the copolymerization of HEMA with PVP, macroporous hydrogels with a pore size of 10-30 μm were obtained. The peculiarities of the structure formation of the obtained copolymers depending on the initial composition formulation were established and their structural parameters were investigated: PVP grafting efficiency, PVP content in copolymer, molecular weight of internodal fragment of polymer network, crosslinking degree, and crosslinking density. The interrelation of sorption-diffusion, physical-mechanical and thermophysical properties along with the structure of the obtained materials was proved. It was shown that with the increasing PVP content in the original composition, the efficiency of its grafting and crosslinking density of the polymer network decreased, but the surface hardness, heat resistance, sorption capacity of copolymers in the dry state, as well as ion permeability and elasticity in the swollen state increased, while their tensile strength deteriorated. It is proved that by changing the original composition formulation it is possible to change the structure and hence the properties of the copolymers in the desired direction.

Acoustic Improvements of Aircraft Headrests Based on Electrospun Mats Evaluated Through Boundary Element Method

This work illustrates the development of passive noise control (PNC) improvements of aircraft headrests to enhance the acoustic comfort for passengers. Two PNC improvements were studied with the aim of reducing the noise perceived by passengers during flight. Two headrest configurations, with and without the lateral caps, and two different materials, a traditional foam and an innovative Silica/Polyvinylpyrrolidone (PVP) woven non-woven mat, were considered, and compared in terms of sound pressure level (SPL) perceived by passengers. Boundary element method (BEM) models were built up to evaluate the acoustic performances of different headrest configurations, varying in terms of shape and textile. A spherical distribution of monopole sources surrounding the headrests was considered as acoustic load, in such a way as to recreate a diffuse acoustic field simulating the cabin noise perceived by passengers during cruise conditions. The impact of the two PNC improvements was analyzed to envisage some general guidelines useful to design advanced headrests from the acoustic viewpoint.

Water Resistant Self-Extinguishing Low Frequency Soundproofing Polyvinylpyrrolidone Based Electrospun Blankets

This paper shows that an eco-friendly electrospinning process allows us to produce water resistant sound absorbers with reduced thickness and excellent sound-absorption properties in the low and medium frequency range (250-1600 Hz) for which which human sensitivity is high and traditional materials struggle to match, that also pass the fire tests which are mandatory in many engineering areas. The structure and composition were studied through Scanning Electron Microscopy (SEM), Fourier Transform InfraRed (FTIR) Spectroscopy and ThermoGravimetric Analysis (TGA). The density, porosity and flow resistivity were measured. Preliminary investigation of the thermal conductivity through Differential Scanning Calorimetry (DSC) shows that they have perspectives also for thermal insulation. The experimental results indicate that the achievements are to be ascribed to the chemical nature of Polyvinylpyrrolidone (PVP). PVP is, in fact, a polymeric lactam with a side polar group that may be easily released by a thermooxidative process. The side polar groups allow for using ethanol for electrospinning than relying on a good dispersion of silica gel particles. The silica particles dimensionally stabilize the mats upon thermal treatments and confer water resistance while strongly contributing to the self-extinguishing property of the materials.

Novel Ni/pHEMA-gr-PVP Composites Obtained by Polymerization with Simultaneous Metal Deposition: Structure and Properties

The synthesis and study of metal-containing hydrogels, particularly those filled with nickel nanoparticles, is currently of interest to many researchers. This paper presents the results of an investigation of the structure and properties of Ni(0)-filled composites on the basis of 2-hydroxyethylmethacrylate copolymers (HEMA) with polyvinylpyrrolidone (PVP) and their hydrogels. The authors of the article are the first who propose the method to produce these materials by combining the processes of polymer matrix synthesis and a reduction of Ni²⁺ ions. Synthesis is carried out in one stage without complicated equipment and is technologically simple. It is determined by thermometric research that the temperature conditions required for the chemical reduction of Ni²⁺ are achieved due to the heat released during the exothermic reaction of HEMA polymerization in the presence of PVP. With the help of Fourier transform infrared analysis, and thermogravimetric and differential-thermal analysis, the formation of a crosslinked graft copolymer based on HEMA and PVP was confirmed, and its structural parameters, including the efficiency of PVP grafting, PVP content in the copolymer, and the molecular weight of the interstitial fragment of the polymer network, were investigated. The results obtained with scanning electron microscopy revealed that the size of the Ni(0) particles is about 500 nm. X-ray structural analysis of the composites obtained confirmed the existence of metal nickel particles. The strength, elastic, sorption, electrical, and magnetic properties of the obtained composites in the solid (dry) and elastic (swollen) physical states, depending on the composition of the copolymer and the content of the metal filler, have been investigated.