Using 445 nm and 970 nm Lasers on Dental Implants-An In Vitro Study on Change in Temperature and Surface Alterations

Bacterial reduction and temperature increase of titanium dental implant models treated with a 445 nm diode laser: an in vitro study

In this in vitro study, the use of a 445 nm diode laser was investigated for the decontamination of titanium dental implants. Different irradiation protocols and the effect of repetitive laser irradiation on temperature increase and decontamination efficacy were evaluated on titanium implant models. An automated setup was developed to realize a scanning procedure for a full surface irradiation to recapitulate a clinical treatment. Three irradiation parameter sets A (continuous wave, power 0.8 W, duty cycle (DC) 100%, and 5 s), B (pulsed mode, DC 50%, power 1.0 W, and 10 s), and C (pulsed mode, DC 10%, power 3.0 W, and 20 s) were used to treat the rods for up to ten consecutive scans. The resulting temperature increase was measured by a thermal imaging camera and the decontamination efficacy of the procedures was evaluated against Escherichia coli and Staphylococcus aureus, and correlated with the applied laser fluence. An implant's temperature increase of 10 °C was set as the limit accepted in literature to avoid thermal damage to the surrounding tissue in vivo. Repeated irradiation of the specimens resulted in a steady increase in temperature. Parameter sets A and B caused a temperature increase of 11.27 ± 0.81 °C and 9.90 ± 0.37 °C after five consecutive laser scans, respectively, while parameter set C resulted in a temperature increase of only 8.20 ± 0.53 °C after ten surface scans. The microbiological study showed that all irradiation parameter sets achieved a complete bacterial reduction (99.9999% or 6-log10) after ten consecutive scans, however only parameter set C did not exceed the temperature threshold. A 445 nm diode laser can be used to decontaminate dental titanium rods, and repeated laser irradiation of the contaminated areas increases the antimicrobial effect of the treatment; however, the correct choice of parameters is needed to provide adequate laser fluence while preventing an implant's temperature increase that could cause damage to the surrounding tissue.

Anti-biofilm activity of 445 nm and 970 nm diode laser on mixed species colonies of- aggregatibacter actinomycetemcomitans and porphyromonas gingivalis cultured on titanium discs -an in vitro study

To assess and compare the anti-microbial efficacy of 445 nm and 970 nm diode laser on mixed species biofilm of Aggregatibacter actinomycetemcomitans [A.a] and Porphyromonas gingivalis [P.g] cultured on machined pure titanium discs. A total of 65 machined pure titanium discs with no surface modifications with a 10-mm diameter and a 2-mm height were sterilized by autoclaving at 121 °C for 15 min and incubated with the commercially available bacterial strains ATCC(American Type Culture Collection- P.g 33277 and A.a 29522)mixture of Aggregatibacter actinomycetemcomitans(A.a) and Porphyromonas gingivalis(P.g).After a 2-week incubation period with the mixture of bacteria to develop a mixed species biofilm, the discs were divided into three groups: (1) no treatment (control), (2) 445 nm laser (test), (3) 970 nm laser (test). For each laser wavelength (445 and 970 nm), the discs were exposed to 1.0 W and 2.0 W in continuous wave mode for the times points of 15, 30, and 60 s. The antimicrobial efficacy was assessed by qPCR. A significant reduction in the levels of both species of bacteria was observed between control and the laser intervention groups. A higher efficacy for the 445 nm diode laser against Porphyromonas gingivalis and a similar efficacy against Aggregatibacter actinomycetemcomitans was observed as compared to the 970 nm group. 445 nm wavelength represents a potential and effective laser wavelength which can be used for the management of peri-implant infection. The present study findings also need to be further validated through clinical interventional trials.

EFFECT OF LOW-LEVEL DIODE LASER ON DENTIN TOPOGRAPHY AND SYMPTOMATIC NONCARIOUS CERVICAL LESIONS PRIOR TO COMPOSITE RESTORATIONS: A SPLIT-MOUTH RANDOMIZED CONTROLLED TRIAL

OBJECTIVES

This study assessed alterations in sensitivity among symptomatic noncarious cervical lesions (NCCLs) following the application of 3 low-level diode laser wavelengths before composite restoration. It analyzed the changes in dentin topography using a scanning electron microscope (SEM).

MATERIALS AND METHODS

Nine patients with 36 NCCLs were randomly assigned intra-individually to 4 groups based on the laser wavelength: laser simulation, 445 nm, 660 nm, and 970 nm. Cavity preparation, irradiation, and composite restoration were performed for each lesion. Sensitivity to cold stimuli was recorded using a visual analog scale (VAS) before the intervention (baseline) and at 1 day, 14 days, 1-, 3-, and 6-month. Pulp sensibility was recorded using an electrical pulp tester (EPT) at baseline, before treatment, and at 3- and 6-month. Additionally, an in vitro examination was performed on 12 extracted human molars to yield 12 dentin discs. Each disc was randomly divided into 4 quadrants to receive the same laser wavelengths to determine the diameters of the tubules using SEM. Results were analyzed statistically for clinical studies by the Friedman test, while ANOVA (RM-ANOVA) was conducted in-vitro, followed by the Bonferroni test in the case of significance (P < .05).

RESULTS

VAS readings decreased across all groups, with a significant decrease observed for 660 nm and 970 nm from 14 days to 6-month, while at 445 nm there was a significant decrease at 6-month compared to the control (P < .05). EPT showed a significant decrease in pain threshold levels at 660 nm and 970 nm at 3- and 6-month, while 445 nm showed a significant decrease at 6-month compared to the control (P < .05). The mean tubular diameter at 445 nm decreased, with no significant difference from the control, whereas a significant decrease was found at 660 nm and 970 nm compared to the control (P < .05).

CONCLUSIONS

Prior to composite restoration in symptomatic NCCLs, diode lasers with a wavelength of 660 nm showed the highest reduction in sensitivity, followed by 970 nm, whereas 445 nm diode lasers showed the least reduction. Additionally, diode lasers with wavelengths of 660 and 970 nm reduced the width of the dentinal tubules (DT) without inducing melting, as viewed under SEM.

The Use of 810 and 1064 nm Lasers on Dental Implants: In Vitro Analysis of Temperature, Surface Alterations, and Biological Behavior in Human Gingival Fibroblasts

Objective: The primary objective of this study was to evaluate the safety of 810 and 1064 nm laser treatment on dental implants. Background: Peri-implantitis is a challenge for clinicians and researchers. Methods: A pig mandible model was used to evaluate temperature increases during laser irradiation. Surface alterations on processed pure titanium discs were analyzed via scanning electron microscopy and measurement of surface contact angles. Processed titanium discs were cocultured in vitro with human gingival fibroblasts; subsequently, cell proliferation was measured. Results: The maximum temperature and time to reach each threshold were comparable. No surface alterations were detected after 810 nm laser irradiation, whereas surface cracks were observed after 1064 nm laser irradiation under the parameter setting of 31.84 W/cm2. Compared with unaltered processed pure titanium discs, the proliferation of human gingival fibroblasts was significantly greater on altered processed pure titanium discs. Conclusions: The use of either 810 or 1064 nm laser treatments may increase the risk of thermal damage in terms of increased temperature if the parameter setting is not warranted. In addition, the use of 1064 nm laser treatment could lead to changes in pure titanium discs that do not negatively affect cell proliferation. Further investigations of laser-assisted therapy are necessary to improve guidelines concerning the treatment of peri-implantitis. Clinical trial registration number: 2021-P2-098-01.

Thermal Effects of 445-nm Diode Laser Irradiation on Titanium and Ceramic Implants

This study aimed to evaluate temperature changes in titanium and ceramic implants after using a 445-nm diode laser under different in vitro conditions. Titanium (Ti) and ceramic (Zr) dental implants were placed into a bone analog, and an intrabony defect was created at each implant. A 445-nm diode laser was used to irradiate the defects for 30 seconds, noncontact, at 2 W in continuous wave (c.w.) and pulsed mode. The experiment was done at room temperature (21.0 ± 1°C) and in a water bath (37.0 ± 1°C). Two thermocouple probes were used to record real-time temperature changes (°C) at the coronal part of the implant (Tc) and the apex (Ta). The temperature was recorded at time 0 (To) and after 30 seconds of irradiation (Tf). The average temperature change was calculated, and a descriptive analysis was conducted (P < .05). The Ti implant resulted in the highest ΔT values coronally (29.6°C) and apically (6.7°C) using continuous wave at 21°C. The Zr implant increased to 26.4°C coronally and 5.2°C apically. In the water bath, the coronal portion of the Ti and Zr implants rose to 14.2°C and 14.01°C, respectively, using continuous waves. The ΔT values for Ti were 11.9°C coronally and 1.7°C apically when placed in a water bath using pulsed mode. The lowest ΔT occurred on the Zr implant with ΔTc and ΔTa of 4.8°C and 0.78°C, respectively. Under in vitro conditions, the 445-nm diode laser in pulsed mode seems to be safe for use on ceramic implants and should be used with caution on titanium implants.

SEM Evaluation of Thermal Effects Produced by a 445 nm Laser on Implant Surfaces

The aim of this in vitro study was to evaluate thermal effects on implant surfaces using a 445 nm diode laser (Eltech K-Laser Srl, Treviso, Italy) with different power settings and irradiation modalities. Fifteen new implants (Straumann, Basel, Switzerland) were irradiated to evaluate surface alteration. Each implant was divided into two zones: the anterior and posterior areas. The anterior coronal areas were irradiated with a distance of 1 mm between the optical fiber and the implant; the anterior apical ones were irradiated with the fiber in contact with the implant. Instead, the posterior surfaces of all of the implants were not irradiated and used as control surfaces. The protocol comprised two cycles of laser irradiation, lasting 30 s each, with a one-minute pause between them. Different power settings were tested: a 0.5 W pulsed beam (T-on 25 ms; T-off 25 ms), a 2 W continuous beam and a 3 W continuous beam. Lastly, through a scanning electron microscopy (SEM) analysis, dental implants' surfaces were evaluated to investigate surface alterations. No surface alterations were detected using a 0.5 W laser beam with a pulsed mode at a distance of 1 mm. Using powers of irradiation of 2 W and 3 W with a continuous mode at 1 mm from the implant caused damage on the titanium surfaces. After the irradiation protocol was changed to using the fiber in contact with the implant, the surface alterations increased highly compared to the non-contact irradiation modality. The SEM results suggest that a power of irradiation of 0.5 W with a pulsed laser light emission mode, using an inactivated optical fiber placed 1 mm away from the implant, could be used in the treatment of peri-implantitis, since no implant surface alterations were detected.

Evaluation of the Photoactivation Effect of 3% Hydrogen Peroxide in the Disinfection of Dental Implants: In Vitro Study

Photoactivation of 3% hydrogen peroxide with a 445 nm diode laser represents a relatively new, insufficiently researched antimicrobial method in the treatment of peri-implantitis. The purpose of this work is to evaluate the effect of photoactivation of 3% hydrogen peroxide with a 445 nm diode laser, and to compare the obtained results with 0.2% chlorhexidine treatment and 3% hydrogen peroxide treatment without photoactivation, in vitro, on the surface of dental implants contaminated with S. aureus and C. albicans biofilms. Previously, 80 infected titanium implants with S. aureus and C. albicans cultures were divided into four groups: G1-negative control (no treatment), G2-positive control (0.2% chlorhexidine), G3 (3% hydrogen peroxide), and G4 (photoactivated 3% hydrogen peroxide). The number of viable microbes in each sample was determined by the colony forming unit (CFU) count. The results were statistically processed and analyzed, showing a statistically significant difference across all groups compared to the negative control (G1), and the absence of a statistically significant difference between groups G1-G3. The new antimicrobial treatment, according to the results, could be worthy of further analysis and research.

A Novel Technique for Disinfection Treatment of Contaminated Dental Implant Surface Using 0.1% Riboflavin and 445 nm Diode Laser—An In Vitro Study

Background: Antimicrobial photodynamic therapy (PDT) has been introduced as a potential option for peri-implantitis treatment. The aim of this study is to evaluate the antimicrobial effect of a novel technique involving a combination of 445 nm diode laser light with 0.1% riboflavin solution (used as a photosensitizing dye) as applied on a bacterial–fungal biofilm formed on implants and to compare the performance of this technique with that of the commonly used combination of 660 nm diode laser with 0.1% methylene blue dye. Methods: An in vitro study was conducted on 80 titanium dental implants contaminated with Staphylococcus aureus (SA) and Candida albicans (CA) species. The implants were randomly divided into four groups: negative control (NC), without surface treatment; positive control (PC), treated with a 0.2% chlorhexidine (CHX)-based solution; PDT1, 660 nm (EasyTip 320 µm, 200 mW, Q power = 100 mW, 124.34 W/cm2, 1240 J/cm2) with a 0.1% methylene blue dye; and PDT2, 445 nm (EasyTip 320 µm, 200 mW, Q power = 100 mW, 100 Hz, 124.34 W/cm2, 1.24 J/cm2) with a 0.1% riboflavin dye. Results: The PDT1 and PDT2 groups showed greater reduction of SA and CA in comparison to the NC group and no significant differences in comparison to the PC group. No statistically significant differences between the PDT1 and PDT2 groups were observed. Conclusions: A novel antimicrobial treatment involving a combination of 445 nm diode laser light with riboflavin solution showed efficiency in reducing SA and CA biofilm formation on dental implant surfaces comparable to those of the more commonly used PDT treatment consisting of 660 nm diode laser light with methylene blue dye or 0.2% CHX treatment.

Thermal effect of a 445 nm diode laser on five dental implant systems: an in vitro study

The purpose of this in vitro study was to assess the thermal effect of the 445 nm diode laser on five dental implant systems. In an ailing implant protocol, five commercial dental implant systems were subjected to 445 nm diode laser energy at different wattages [W], exposure times, and modes (continuous wave [CW] vs. pulsed and contact vs. non-contact) of laser beam delivery. Scanning electron microscopy (SEM) allowed the evaluation of irradiated implant surfaces. A total of 2880 temperature response curves were recorded. The 445 nm wavelength caused temperature increases of more than 10 °C at or above the 0.8 W power level working in CW mode for 5 s and in pulsed mode at 3 W for 20 s with 10% duty cycle. Highest rises in temperature were seen in the Straumann Pure ceramic implant, lowest in the Ankylos system. SEM analysis revealed no surface alteration in all systems in non-contact mode. The applied laser is not inherently safe for the decontamination of ailing implants. From the results of this study it was concluded that different dental implant materials and geometries show different temperature response curves when subjected to 445 nm diode laser energy. Clinicians ought to be aware of this. Therefore, manufacturers of laser devices should provide implant-specific laser parameters for the decontamination process. However, both laser irradiation systems can prevent harmful rises in temperature and surface alteration when used at moderate laser parameters.