Acrylonitrile Butadiene Styrene and Polypropylene Blend with Enhanced Thermal and Mechanical Properties for Fused Filament Fabrication

Effects of Contamination with Selected Polymers on the Mechanical Properties of Post-Industrial Recycled Polypropylene

The effect of contamination of polypropylene (PP) with selected polymers is studied to simulate the effect of mis-sorting in recycling streams. Polystyrene (PS), polyethylene terephthalate (PET), polycarbonate (PC), acrylonitrile butadiene styrene (ABS), and polylactic acid (PLA) were compounded with PP at different concentrations varying between 3 and 10%. Infrared spectroscopy proved the absence of chemical bonds between the constituents. Generally, melt flowability, except for the PP/PLA blend, and crystallinity were only slightly affected by the incorporation of the contaminating polymers. Samples of the polymer blends were injection moulded and further tested for their tensile and impact properties. Critical behaviour was induced by the introduction of a weld line as a result of the application of multiple gating points during injection moulding. Results generally show the applicability of PP mixtures within the investigated range of contamination, without much sacrifice in mechanical performance. However, in the case of ABS and PLA, more care should be taken when designing complex parts with weld lines, due to reduced toughness.

Sustainable strategies towards better utilization of synthetic polymers

The abstract provides an overview of a study focused on analyzing diverse strategies to achieve sustainable utilization of synthetic polymers through effective waste management. The escalating global consumption of synthetic polymers has precipitated a concerning increase in plastic waste and environmental degradation. To address this challenge, novel materials with specified application goals, such as engineered plastic, have been developed and are intended for recycling and reuse. Despite the reuse and recycling, when plastic gets disposed into the environment, the degradation properties of plastics render a direct disposal hazard, posing a significant environmental threat. To mitigate these issues, the concept of replacing specific monomers of engineered synthetic plastics with bio-alternatives or blending them with other polymers to enhance sustainability and environmental compatibility has emerged. In this study, Acrylonitrile Butadiene Styrene (ABS) plastic is the focal material, and three distinct investigations were conducted. First, replacing ABS plastic's butadiene monomer with natural rubber was explored for its properties and environmental impact. Second, ABS plastic was blended with virgin, recycled, and bio-alternatives of PET (polyethylene terephthalate) and PVC (polyvinyl chloride) polymers. Lastly, recycled ABS blended with recycled PET and PVC was analyzed for mechanical properties. Comparative assessments of these blends were made based on mechanical properties, carbon emissions, and cost-effectiveness. The study determined that the r-ABS/r-PVC (recycled) blend exhibited the most favorable characteristics for practical application.

Classification, processing, and applications of bioink and 3D bioprinting: A detailed review

With the advancement in 3D bioprinting technology, cell culture methods can design 3D environments which are both, complex and physiologically relevant. The main component in 3D bioprinting, bioink, can be split into various categories depending on the criterion of categorization. Although the choice of bioink and bioprinting process will vary greatly depending on the application, general features such as material properties, biological interaction, gelation, and viscosity are always important to consider. The foundation of 3D bioprinting is the exact layer-by-layer implantation of biological elements, biochemicals, and living cells with the spatial control of the implantation of functional elements onto the biofabricated 3D structure. Three basic strategies underlie the 3D bioprinting process: autonomous self-assembly, micro tissue building blocks, and biomimicry or biomimetics. Tissue engineering can benefit from 3D bioprinting in many ways, but there are still numerous obstacles to overcome before functional tissues can be produced and used in clinical settings. A better comprehension of the physiological characteristics of bioink materials and a higher level of ability to reproduce the intricate biologically mimicked and physiologically relevant 3D structures would be a significant improvement for 3D bioprinting to overcome the limitations.

Methods of Preparation and Performance Evaluation of ABS/Mineral Microsphere Composites Produced through FDM and Compression Molding

The use of amorphous microspheres as filler in composites is promising due to their light weight, low cost, incombustibility, and the ability to alter relevant properties of the final composite. Contrary to glass spheres, perlite microspheres are much cheaper and can be tailor-made to facilitate purpose-oriented alteration of the final composite. We report the use of perlite microspheres for the preparation of: (1) composites, through a compression molding (hot pressing) technique; and (2) composite filaments, in a single screw extruder, as well as their use for sample printing through Fused Deposition Modeling (FDM). Proper characterization of the produced composites allows for their evaluation in terms of physical, thermal, and mechanical properties and with regards to the manufacturing technique, the filler fraction, and size. Composite samples of acceptable quality in terms of filler survival and dispersion as well as mechanical properties were produced through compression molding using fine expanded perlite microspheres (<90 μm) up to an infill ratio of 40 vol.%. Fine fillers (<90 μm) performed well in FDM, allowing printing of composite dogbone samples with a higher Young’s modulus and elongation and similar ultimate tensile strength compared to benchmark, up to an infill ratio of 20 vol.%. Composite samples present a slightly lower burning rate compared to those produced solely by ABS. Perlite microspheres present good workability in both applications, possessing satisfactory performance as filler in the composites, and can thus be assumed a promising multifunctional filler for various thermoplastics considering their low price, environmental impact, and fire rating.

Experimental Investigation and Prediction of Mechanical Properties in a Fused Deposition Modeling Process

Additive manufacturing, also known as three-dimensional printing, is a computer-controlled advanced manufacturing process that produces three-dimensional items by depositing materials directly from a computer-aided design model, usually in layers. Due to its capacity to manufacture complicated objects utilizing a wide range of materials with outstanding mechanical qualities, fused deposition modeling is one of the most commonly used additive manufacturing technologies. For printing high-quality components with appropriate mechanical qualities, such as tensile strength and flexural strength, the selection of adequate processing parameters is critical. Experimentally, the influence of process parameters such as the raster angle, printing orientation, air gap, raster width, and layer height on the tensile strength of fused deposition modeling printed items was examined in this work. Through analysis of variance, the impact of each parameter was measured and rated. The system’s response was predicted using an adaptive neuro-fuzzy technique and an artificial neural network. In Minitab software, the Box-Behnken response surface experimental design was used to generate 46 experimental trials, which were then printed using acrylonitrile butadiene styrene polymer materials on a three-dimensional forge dreamer II fused deposition modelling printing machine. The results revealed that the raster angle, air gap, and raster width had significant impacts on the tensile strength. The adaptive neuro-fuzzy approach and artificial neural network predicted tensile strength accurately with an average percentage error of 0.0163 percent and 1.6437 percent, respectively. According to the findings, the model and experimental data are in good agreement.

Partial Biodegradable Blend for Fused Filament Fabrication: In-Process Thermal and Post-Printing Moisture Resistance

Despite the extensive research, the moisture-based degradation of the 3D-printed polypropylene and polylactic acid blend is not yet reported. This research is a part of study reported on partial biodegradable blends proposed for large-scale additive manufacturing applications. However, the previous work does not provide information about the stability of the proposed blend system against moisture-based degradation. Therefore, this research presents a combination of excessive physical interlocking and minimum chemical grafting in a partial biodegradable blend to achieve stability against in-process thermal and moisture-based degradation. In this regard, a blend of polylactic acid and polypropylene compatibilized with polyethylene graft maleic anhydride is presented for fused filament fabrication. The research implements, for the first time, an ANOVA for combined thermal and moisture-based degradation. The results are explained using thermochemical and microscopic techniques. Scanning electron microscopy is used for analyzing the printed blend. Fourier transform infrared spectroscopy has allowed studying the intermolecular interactions due to the partial blending and degradation mechanism. Differential scanning calorimetry analyzes the blending (physical interlocking or chemical grafting) and thermochemical effects of the degradation mechanism. The thermogravimetric analysis further validates the physical interlocking and chemical grafting. The novel concept of partial blending with excessive interlocking reports high mechanical stability against moisture-based degradation.

Glass Powder Additive on Recycled Polypropylene Filaments: A Sustainable Material in 3D Printing

This study aimed to characterize the effect of a glass powder additive on recycled polypropylene (rPP) materials from food packaging to be used as filaments in material extrusion (MEX) 3D printing applications. The composite filaments studied were rPP filaments with glass powder (GP) additive in the 2.5%, 5%, and 10% fractions. As a baseline, the filaments made of pure virgin PP and rPP without additive were used. The filament that has been successfully made is then printed into a tensile test specimen and an impact test to observe its mechanical properties. Fourier-transform infrared spectroscopy (FTIR) characterization was also carried out to determine the effect of chemical bonding and thermal characterization using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results of FTIR characterization on the sample rPP + 10% do not show a typical peak shift of PP, but give rise to new peaks at wavenumbers of 1000 cm⁻¹ (Si-O-Na), 890 cm⁻¹ (Si-H) and 849 cm⁻¹ (O-Si-O), which indicate the typical peaks of the glass constituent compounds. In the thermal characteristics, the addition of GP shows the improved stability of mass changes to heat and increases the melting temperature of rPP. The ultimate tensile strength and Young’s modulus for rPP-based specimens with 10% GP additive showed an increase of 38% and 42% compared to PP specimens. In addition to the improved mechanical strength, the addition of GP also reduces the bending deformation, which can be well controlled, and reduces curvature, which is a problem in semicrystalline polymer-based filaments.

Effects of In-Process Temperatures and Blending Polymers on Acrylonitrile Butadiene Styrene Blends

Acrylonitrile butadiene styrene (ABS) is a renowned commodity polymer for additive manufacturing, particularly fused deposition modelling (FDM). The recent large-scale applications of 3D-printed ABS require stable mechanical properties than ever needed. However, thermochemical scission of butadiene bonds is one of the contemporary challenges affecting the overall ABS stability. In this regard, literature reports melt-blending of ABS with different polymers with high thermal resistance. However, the comparison for the effects of different polymers on tensile strength of 3D-printed ABS blends was not yet reported. Furthermore, the cumulative studies comprising both blended polymers and in-process thermal variables for FDM were not yet presented as well. This research, for the first time, presents the statistical comparison of tensile properties for the added polymers and in-process thermal variables (printing temperature and build surface temperature). The research presents Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) to explain the thermochemical reasons behind achieved mechanical properties. Overall, ABS blend with PP shows high tensile strength (≈31 MPa) at different combinations of in-process parameters. Furthermore, some commonalities among both blends are noted, i.e., the tensile strength improves with increase of surface (bed) and printing temperature.

Partial Polymer Blend for Fused Filament Fabrication with High Thermal Stability

The materials for large scale fused filament fabrication (FFF) are not yet designed to resist thermal degradation. This research presents a novel polymer blend of polylactic acid with polypropylene for FFF, purposefully designed with minimum feasible chemical grafting and overwhelming physical interlocking to sustain thermal degradation. Multi-level general full factorial ANOVA is performed for the analysis of thermal effects. The statistical results are further investigated and validated using different thermo-chemical and visual techniques. For example, Fourier transform infrared spectroscopy (FTIR) analyzes the effects of blending and degradation on intermolecular interactions. Differential scanning calorimetry (DSC) investigates the nature of blending (grafting or interlocking) and effects of degradation on thermal properties. Thermogravimetric analysis (TGA) validates the extent of chemical grafting and physical interlocking detected in FTIR and DSC. Scanning electron microscopy (SEM) is used to analyze the morphology and phase separation. The novel approach of overwhelmed physical interlocking and minimum chemical grafting for manufacturing 3D printing blends results in high structural stability (mechanical and intermolecular) against thermal degradation as compared to neat PLA.

Influence of Infill Pattern on Mechanical Behavior of Polymeric and Composites Specimens Manufactured Using Fused Filament Fabrication Technology

This paper presents the results of a comparative evaluation of the tensile strength behaviors of parts obtained by additive manufacturing using fused filament fabrication (FFF) technology. The study investigated the influences of the deposition printing parameters for both polymers and fiber-reinforced polymers. Polymeric materials that are widely used in FFF were selected, including acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), and nylon. Carbon and glass continuous fibers were used to reinforce the nylon matrix in composite materials. The study utilized two manufacturing methods. Polymers were manufactured using an Ultimaker 2 Extended+ device and the fiber-reinforced polymer specimens were obtained using a Markforged Mark Two printer. The entire set of specimens was eventually subjected to destructive monoaxial tensile tests to measure their responses. The main goal of this study was to estimate the effect of the different infill patterns applied (zig-zag, concentric, and four different orientations lines) on the mechanical properties of pure thermoplastic materials and reinforced polymers. Results show a spectacular increase in the tensile stress at break, which for polymers reaches an average value of 27.53 MPa compared to 94.51 MPa in the case of composites (increase of 70.87%). A similar increase occurs in the case of tensile stress at yield with values of 31.87 MPa and 105.98 MPa, respectively, which represents an increase of 69.93%. The influence of the infill of the fiber is decisive, reaching, in the 0-0 arrangement, mean values of 220.18 MPa for tensile stress at break and 198.26 MPa for tensile stress at yield.

Reusability of autoclaved 3D printed polypropylene compared to a glass filled polypropylene composite

Health care waste can be a costly expenditure for facilities as specific disposal methods must be used to prevent the spread of pathogens. If more multi-use medical devices were available, it could potentially relieve some of this burden; however, sterilization between uses is important in preventing disease transmission. 3D printing has the ability to easily create custom medical devices at a low cost, but the majority of filaments utilized cannot survive steam sterilization. Polypropylene (PP) can withstand autoclave temperatures, but is difficult to print as it warps and shrinks during printing; however, a composite PP filament reduces these effects. Commercially available PP and glass filled PP (GFPP) filaments were successfully 3D printed into 30 × 30 × 30 mm cubes with no shrinking or warping and were autoclaved. The 134 °C autoclave temperature was too high as several cubes melted after two to three rounds, but both PP and GFPP cubes displayed minimal changes in mass and volume after one, four, seven, and ten rounds of autoclaving at 121 °C. GFPP cubes autoclaved zero, four, seven, and ten times had significantly smaller average compressive stress values compared to all PP groups, but the GFPP cubes autoclaved once were only less than PP cubes autoclaved zero, seven and ten times. GFPP cubes autoclaved zero, one, four, and seven times also deformed less indicating that the embedded glass fibers provided additional strength. While a single method was found that successfully printed PP and GFPP cubes that were able to survive up to ten rounds of autoclaving, future work should include further investigation into the mechanical properties and increasing the number of autoclave rounds.

Screw-assisted 3D printing with granulated materials: a systematic review

This paper presents a systematic review on extrusion additive manufacturing (EAM), with focus on the technological development of screw-assisted systems that can be fed directly with granulated materials. Screw-assisted EAM has gained importance as an enabling technology to expand the range of 3D printing materials, reduce costs associated with feedstock fabrication, and increase the material deposition rate compared to traditional fused filament fabrication (FFF). Many experimental printheads and commercial systems that use some screw-processing mechanism can be found in the literature, but the design diversity and lack of standard terminology make it difficult to determine the most suitable solutions for a given material or application field. Besides, the few previous reviews have offered only a glimpse into the topic, without an in-depth analysis about the design of the extruders and associated capabilities. A systematic procedure was devised to identify the screw-assisted EAM systems that can print directly from granulated materials, resulting in 61 articles describing different pieces of equipment that were categorized as experimental printheads and commercial systems, for small- and large-scale applications. After describing their main characteristics, the most significant extruder modifications were discussed with reference to the materials processed and performance requirements. In the end, a general workflow for the development of 3D printers based on screw extrusion was proposed. This review intends to provide information about the state-of-the-art screw-assisted EAM and help the academy to identify further research opportunities in the field.

Synergistic lignin construction of a long-chain branched polypropylene and its properties

In light of current environmental pressures (referring to its destruction) and the consumption of petrochemical resources, the substitution of chemicals products with renewable natural substances has attracted extensive interest. In this paper, a synergistically constructed lignin polypropylene matrix composite with long-chain branched characteristics was prepared by a pre-irradiation and melt blending method. The effects of lignin on the crystallization, rheological behavior, foaming and aging properties of polypropylene were studied. Differential scanning calorimetry and polarized light microscopy results show that lignin undergoes heterophasic nucleation in a polypropylene matrix; rheological studies show that lignin promotes the formation of a heterogeneous polypropylene network, and thus polypropylene exhibits long-chain branching features; nucleation and a network structure endow the polypropylene-based composites with uniform cell size, thin cell walls, and a foaming ratio of 5–44 times; at the same time, a large number of hindered phenols in lignin can capture free radicals to improve the aging properties of the polypropylene. This research will help to convert industrial waste into functional composite materials.

Polypropylene with long chain branching behavior was constructed by lignin, which foaming property and polarity were improved.

Evolution of 3D Printing Methods and Materials for Electrochemical Energy Storage

Additive manufacturing has revolutionized the building of materials, and 3D-printing has become a useful tool for complex electrode assembly for batteries and supercapacitors. The field initially grew from extrusion-based methods and quickly evolved to photopolymerization printing, while supercapacitor technologies less sensitive to solvents more often involved material jetting processes. The need to develop higher-resolution multimaterial printers is borne out in the performance data of recent 3D printed electrochemical energy storage devices. Underpinning every part of a 3D-printable battery are the printing method and the feed material. These influence material purity, printing fidelity, accuracy, complexity, and the ability to form conductive, ceramic, or solvent-stable materials. The future of 3D-printable batteries and electrochemical energy storage devices is reliant on materials and printing methods that are co-operatively informed by device design. Herein, the material and method requirements in 3D-printable batteries and supercapacitors are addressed and requirements for the future of the field are outlined by linking existing performance limitations to requirements for printable energy-storage materials, casings, and direct printing of electrodes and electrolytes. A guide to materials and printing method choice best suited for alternative-form-factor energy-storage devices to be designed and integrated into the devices they power is thus provided.

Expanding Puck and Schürmann Inter Fiber Fracture Criterion for Fiber Reinforced Thermoplastic 3D-Printed Composite Materials

The present work expands the application of Puck and Schürmann Inter-Fiber Fracture criterion to fiber reinforced thermoplastic 3D-printed composite materials. The effect of the ratio between the transverse compressive strength and the in-plane shear strength is discussed and a new transition point between the fracture conditions under compressive loading is proposed. The recommended values of the inclination parameters, as well as their effects on the proposed method, are also discussed. Failure envelopes are presented for different 3D-printed materials and also for traditional composite materials. The failure envelopes obtained here are compared to those provided by the original Puck and Schürmann criterion and to those provided by Gu and Chen. The differences between them are analyzed with the support of geometrical techniques and also statistical tools. It is demonstrated that the Expanded Puck and Schürmann is capable of providing more suitable failure envelopes for fiber reinforced thermoplastic 3D-printed composite materials in addition to traditional semi-brittle, brittle and intrinsically brittle composite materials.