Utilization of Composts for Adsorption of Methylene Blue from Aqueous Solutions: Kinetics and Equilibrium Studies

Influence of Zinc and Humic Acids on Dye Adsorption from Water by Two Composts

Searching for alternative low-cost biosorbents for the removal of textile dyes from wastewater is currently an important subject of research. In this work, we have investigated how the presence of other contaminants in textile wastewaters can affect dye adsorption by biosorbents. We tested the adsorption of three dyes of different types: Basic Violet 10 (BV10), Acid Blue 113 (AB113) and Direct Blue 71 (DB71) by two different composts-municipal solid waste compost and pine bark compost-in the presence of Zn (5 mg L^-1) or dissolved organic matter (100 mg humic acids L^-1) in batch experiments. Dye adsorption capacity for both composts followed the following sequence: BV10 > AB113 > DB71. In general, dye sorption at the equilibrium was adequately described by the Freundlich model, but not always by the Langmuir model, which did not allow for the estimation of maximum retention capacities in all cases. In general, these were around 1 mg g^-1 for DB71, 2 mg g^-1 for AB113, and 40 mg g^-1 for BV10. Municipal solid waste compost had slightly higher affinity than pine bark compost for the anionic dyes AB113 and DB71, whereas for the cationic dye BV10, pine bark compost presented a much higher adsorption capacity (41.7 mg g^-1 versus 6.8 mg g^-1). The presence of Zn or dissolved organic matter in the solutions at typical wastewater concentrations did not decrease the dye adsorption capacity of the composts. This result is positive both for the real application of composts to real textile wastewaters and for the validity of the results of biosorbent performance obtained with single-dye solutions.

Comparison of the sorption capacity of basic, acid, direct and reactive dyes by compost in batch conditions

Research on biosorption of organic dyes is an important subject for the development of clean technologies for the treatment of textile wastewater. In this work, the process of sorption of four textile dyes of different natures, namely Basic Violet 10 (BV10), Acid Red 27 (AR27), Direct Blue 151 (DB151) and Reactive Violet 4 (RV4) onto two composts, pine bark compost and municipal solid waste compost, has been studied. For this, sorption kinetics and equilibrium sorption at different solution pH values (3.0-7.0) and salinity (0-1.0 M KCl) conditions have been assessed in batch experiments. Sorption rates were relatively slow for BV10, reaching equilibrium only after 24 h, and faster for the rest: around 5-6 h for RV4 and AR27 and 2 h for DB151. Kinetics of dye sorption followed a pseudo-first order model, except that of DB151, which was better described by a pseudo-second order model. The sequence of adsorption capacity for both composts was as follows: BV10 > DB151 > RV4 > AR27. In general, dye sorption at the equilibrium was adequately described by the Langmuir model, what allows to estimate maximum retention capacities for each dye by the composts. At the best removal conditions, pine bark compost presented maximum sorption capacities of 204 mg g^-1 for BV10, 54 mg g^-1 for DB151, 23 mg g^-1 for RV4, and 4.1 mg g^-1 for AR27, whereas municipal solid waste compost showed maximum sorption of 74 mg g^-1 for DB151, 38 mg g^-1 for RV4, 36 mg g^-1 for BV10, and 1.6 mg g^-1 for AR27. Sorption increased at acid pH in all cases, likely because of modification of charges of the dyes and higher electrostatic attraction, whereas increasing salinity also had a positive effect on sorption, attributed to a solute-aggregation mechanism in solution. In conclusion, organic waste-derived products, like composts, can be applied in the removal of colorants from wastewater, although they would be more effective for the removal of basic cationic dyes than other types, due to electrostatic interaction with mostly negatively-charged composts.

Assessment of the Composition of Forest Waste in Terms of Its Further Use

This paper presents the results of the analysis of the chemical composition and content of heavy metal contamination in forest logging residues, in order to assess the possibility for their further utilisation. The samples were divided into 9 groups, which included coniferous tree cones, wood, and other multi-species logging residues. The elementary composition, ash content, and calorific value were determined as energy use indicators for the samples. Additionally, the content of heavy and alkali metals, which may affect combustion processes and pollutant emissions, was tested. The high content of heavy metals may also disqualify these residues for other uses. The research shows that the test residues are suitable for energy use due to their high calorific value and low content of heavy metals. However, an increased ash content in some samples and the presence of alkali metals, causing high-temperature corrosion of boilers, may disqualify them as a potential fuel in the combustion process. The forest residues may be used in other thermal processes such as pyrolysis or gasification. A low content of heavy metals and a high content of organic matter permit the use of these residues for the production of adsorbents or composite materials.