The Photocatalytic Activity of Titania Coatings Produced by Electrochemical and Chemical Oxidation of Ti6Al4V Substrate, Estimated According to ISO 10678:2010The Photocatalytic Activity of Titania Coatings Produced by Electrochemical and Chemical Oxidation of Ti6Al4V Substrate, Estimated According to ISO 10678:2010

Evaluation of the Cathodic Electrodeposition Effectiveness of the Hydroxyapatite Layer Used in Surface Modification of Ti6Al4V-Based Biomaterials

The important issue associated with the design and the fabrication of the titanium and titanium alloy implants is the increase of their biointegration with bone tissue. In the presented paper, the research results concerning the conditions used in the cathodic deposition of hydroxyapatite on the surface Ti6Al4V substrates primarily modified by the production of TiO₂ nanoporous coatings, TiO₂ nanofibers, and titanate coatings, are discussed. Despite excellent biocompatibility with natural bone tissue of materials based on hydroxyapatite (HA), their poor adhesion to the substrate caused the limited use in the implants' construction. In our works, we have focused on the comparison of the structure, physicochemical, and mechanical properties of coating systems produced at different conditions. For this purpose, scanning electron microscopy images, chemical composition, X-ray diffraction patterns, infrared spectroscopy, wettability, and mechanical properties are analyzed. Our investigations proved that the intermediate titanium oxide coatings presence significantly increases the adhesion between the hydroxyapatite layer and the Ti6Al4V substrate, thus solving the temporary delamination problems of the HA layer.

Indoor Air Photocatalytic Decontamination by UV–Vis Activated CuS/SnO2/WO3 Heterostructure

A titania-free heterostructure based on CuS/SnO2/WO3 was obtained by a three-step sol–gel method followed by spray deposition on the glass substrate. The samples exhibit crystalline structures and homogenous composition. The WO3 single-component sample morphology consists of fibers that serve as the substrate for SnO2 development. The CuS/SnO2/WO3 heterostructure is characterized by a dense granular morphology. Photocatalytic activity was evaluated under UV–Vis radiation and indicates that the WO3 single-component sample is able to remove 41.1% of acetaldehyde (64.9 ppm) and 52.5% of formaldehyde (81.4 ppm). However, the CuS/SnO2/WO3 exhibits a superior photocatalytic activity due to a larger light spectrum absorption and lower charge carrier recombination rate, allowing the removal of 69.2% of acetaldehyde and 78.5% of formaldehyde. The reusability tests indicate that the samples have a stable photocatalytic activity after three cycle (12 h/cycle) assessments. During light irradiation, the heterostructure acted as a Z-scheme mechanism using the redox ability of the CuS conduction band electrons and the SnO2/WO3 valence band holes to generate the oxidative species required for VOC removal.

Titanium(IV) Oxo-Complex with Acetylsalicylic Acid Ligand and Its Polymer Composites: Synthesis, Structure, Spectroscopic Characterization, and Photocatalytic Activity

The titanium oxo complexes are widely studied, due to their potential applications in photocatalytic processes, environmental protection, and also in the biomedical field. The presented results concern the oxo complex synthesized in the reaction of titanium(IV) isobutoxide and acetylsalicylic acid (Hasp), in a 4:1 molar ratio. The structure of isolated crystals was solved using the single-crystal X-ray diffraction method. The analysis of these data proves that [Ti₄O₂(OⁱBu)₁₀(asp)₂]·H₂O (1) complex is formed. Moreover, the molecular structure of (1) was characterized using vibrational spectroscopic techniques (IR and Raman), ¹³C NMR, and UV–Vis diffuse reflectance spectroscopy (UV–Vis DRS). The photocatalytic activity of the synthesized complex was determined with the use of composite foils produced by the dispersion of (1) micrograins, as the inorganic blocks, in a polycaprolactone (PCL) matrix (PCL + (1)). The introduction of (1) micrograins to the PCL matrix caused the absorption maximum shift up to 425–450 nm. The studied PCL + (1) composite samples reveal good activity toward photodecolorization of methylene blue after visible light irradiation.

Oxo-Titanium(IV) Complex/Polymer Composites-Synthesis, Spectroscopic Characterization and Antimicrobial Activity Test

The emergence of a large number of bacterial strains resistant to many drugs or disinfectants currently used contributed to the search of new, more effective antimicrobial agents. In the presented paper, we assessed the microbiocidal activity of tri- and tetranuclear oxo-titanium(IV) complexes (TOCs), which were dispersed in the poly(methyl methacrylate) (PMMA) matrix. The TOCs were synthesized in reaction to Ti(OR)₄ (R = ⁱPr, ⁱBu) and HO₂CR' (R' = 4-PhNH₂ and 4-PhOH) in a 4:1 molar ratio at room temperature and in Ar atmosphere. The structure of isolated oxo-complexes was confirmed by IR and Raman spectroscopy and mass spectrometry. The antimicrobial activity of the produced composites (PMMA + TOCs) was estimated against Gram-positive (Staphylococcus aureus ATCC 6538 and S. aureus ATCC 25923) and Gram-negative (Escherichia coli ATCC 8739 and E. coli ATCC 25922) bacteria and yeasts of Candida albicans ATCC 10231. All produced composites showed biocidal activity against the bacteria. Composites containing {Ti₄O₂} cores and the {Ti₃O} core stabilized by the 4-hydroxybenzoic ligand showed also high activity against yeasts. The results of investigations carried out suggest that produced (PMMA + TOCs) composites, due to their microbiocidal activity, could find an application in the elimination of microbial contaminations in various fields of our lives.