Preparation and Characterization of Defective TiO2. The Effect of the Reaction Environment on Titanium Vacancies Formation

Is Black Titania a Promising Photocatalyst?

Five different (commercial and self-synthesized) titania samples were mixed with NaBH4 and then heated to obtain black titania samples. The change in synthesis conditions resulted in the preparation of nine different photocatalysts, most of which were black in color. The photocatalysts were characterized by various methods, including X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), photoacoustic and reverse-double beam photoacoustic spectroscopy (PAS/RDB-PAS). The photocatalytic activity was tested for oxidative decomposition of acetic acid, methanol dehydrogenation, phenol degradation and bacteria inactivation (Escherichia coli) under different conditions, i.e., irradiation with UV, vis, and NIR, and in the dark. It was found that the properties of the obtained samples depended on the features of the original titania materials. A shift in XRD peaks was observed only in the case of the commercial titania samples, indicating self-doping, whereas faceted anatase samples (self-synthesized) showed high resistance towards bulk modification. Independent of the type and degree of modification, all modified samples exhibited much worse activity under UV irradiation than original titania photocatalysts both under aerobic and anaerobic conditions. It is proposed that the strong reduction conditions during the samples’ preparation resulted in the partial destruction of the titania surface, as evidenced by both microscopic observation and crystallographic data (an increase in amorphous content), and thus the formation of deep electron traps (bulk defects as oxygen vacancies) increasing the charge carriers’ recombination. Under vis irradiation, a slight increase in photocatalytic performance (phenol degradation) was obtained for only four samples, while two samples also exhibited slight activity under NIR. In the case of bacteria inactivation, some modified samples exhibited higher activity under both vis and NIR than respective pristine titania, which could be useful for disinfection, cancer treatment and other purposes. However, considering the overall performance of the black titania samples in this study, it is difficult to recommend them for broad environmental applications.

Synthesis and Evaluation of FeSX/TiO2 for the Photocatalytic Degradation of Phenol under Visible-Light Region

In the present work, phenol was used as a model molecule to the photocatalytic evaluation of TiO2 impregnated with iron sulphide and chlorine on a visible-light reactor. The iron–chlorine catalyst was prepared by incipient impregnation with the metal precursors, Fe (NO3)3 and NaCl on previously calcined TiO2. The catalyst was sulphurized with H2S at 300 °C for 1 h. The catalysts were prepared at different chlorine concentrations using HYDRA chemical equilibrium diagrams to obtain different fractions of FeCl+. The oxide catalysts were characterized with diffuse reflectance (DRS UV–Vis) and temperature programmed reduction analysis (TPR). Sulphurized catalysts were characterized with Raman spectrometry and X-ray photoelectron spectrometry (XPS). The FeS–2Cl/TiO2 catalyst presented 8.35 times higher photodegradation than TiO2 and 6.4 times higher compared to the FeS–0.25Cl/TiO2 catalyst. DRS and XPS showed similar results of band gap, proving that the catalyst remain stable after sulphurisation. The TPR results of FeS–2Cl/TiO2 showed an increment of 86.29% in Fe2+/Fe3+ compared to FeS–0.25Cl/TiO2. XPS and Raman results for oxide and sulphated iron species relation suggested that FeS–2Cl/TiO2 decreased 4.45% compared to FeS–0.25Cl/TiO2 catalyst. XPS semiquantitative for S/Fe results showed that the FeS–2Cl/TiO2 catalyst increased 73.17% in comparison to FeS–0.25Cl/TiO2. These results suggested the increment of sulphurisation degree for FeS–2Cl/TiO2. In this regard, the catalyst characterization results showed that the presence of FeCl+ (0.85 fractions) in solution before impregnation promoted the active sulphide species maintaining the band gap and improved the degradation of phenol on visible light.

TiO2 Nanoparticles Dispersion in Block-Copolymer Aqueous Solutions: Nanoarchitectonics for Self-Assembly and Aggregation

Achieving homogenous dispersion of nanoparticles inside a polymeric matrix is a great challenge for numerous applications. In the present study, we aim at understanding the role of different factors on the dispersion properties of TiO₂ in pluronic F-127 mixtures. The mixtures were prepared with different pH and guest/host ratios and investigated by UV-Vis spectroscopy, dynamic light scattering, infrared spectroscopy and electrical conductivity. Depending on the preparation conditions, different amounts of TiO₂ were loaded within the copolymer as quantitatively determined by UV-Vis spectroscopy. The different content of nanoparticles has direct implications on the gelation and micellization of pluronic analyzed by dynamic light scattering. The information derived on the self-assembly behavior was interpreted in relation to the infrared and conductivity measurements results. Together, these results shed light on the most favorable conditions for improving the nanoparticle dispersion inside the copolymer matrix and suggest a possible strategy to design functional nanoparticle-polymer systems.

Improving the Imazapyr Degradation by Photocatalytic Ozonation: A Comparative Study with Different Oxidative Chemical Processes

The degradation of imazapyr (C13H15N3O3), an active element in the aqueous solution of commercial herbicide, was investigated. This study was the first to evaluate in a comprehensive manner the efficiency of advanced oxidation processes for imazapyr degradation. Results showed that Imazapyr degradation is significantly affected by operational conditions such as TiO2 concentration, ozone concentration, initial concentration of imazapyr and pH. The kinetics of Imazapyr consumption was the first order with respect to Imazapyr concentration and zero order with respect to ozone concentration with a constant rate of 0.247 min−1 and 0.128 min−1 for photocatalytic ozonation and heterogeneous photocatalysis, while it was the first order with respect to Imazapyr and the first order with respect to ozone concentrations when only ozone was used with a constant rate of 0.053 mol L−1 min−1 at pH 7. The results revealed that more than 90 percent of the removal efficiency representing the elimination of imazapyr was held up to 7 μM. Further increase in the concentration of imazapyr leads to a drop in the removal efficiency, however the total imazapyr degradation was reached in 20 min utilizing photocatalytic ozonation for 5 μM of Imazapyr in the presence of 100 mg L−1 of TiO2, 10 mg L−1 of ozone at pH 7. Photocatalytic ozonation and heterogeneous photocatalysis utilizing TiO2 as a semiconductor process appeared possible and well suited for the treatment of organic contaminants such as imazapyr herbicides, although at certain dosages of pH and common time for wastewater treatment, imazapyr was not degraded with ozonation on its own. The association of two oxidation processes, ozonation and photocatalysis, has improved oxidation efficiencies for water treatment under optimal conditions, leading to the development of non-selective hydroxyl and more reactive radicals in the oxidation medium, as well as the resulting synergistic effects between photocatalysis and ozonation that react more rapidly with imazapyr herbicide.