New Insights into Osteointegration and Delamination from a Multidisciplinary Investigation of a Failed Hydroxyapatite-Coated Hip Joint Replacement

Outcomes of total hip arthroplasty using collared versus collarless uncemented HA-coated stems: a meta-analysis

Purpose

to systematically review comparative studies reporting revision rates, clinical outcomes, or radiographic outcomes of total hip arthroplasty (THA) using collared versus collarless conventional-length uncemented hydroxyapatite (HA)-coated stems.

Methods

In adherence with PRISMA guidelines, a literature search was performed on Medline, Embase, and Scopus. Comparative clinical studies were eligible if they reported outcomes of collared versus collarless uncemented HA-coated stems for primary THA. Two reviewers screened titles, abstracts, and full-texts to determine eligibility; then performed data extraction; and assessed the quality of studies according to Joanna Briggs Institute (JBI) checklist.

Results

The search returned 972 records, 486 were duplicates, and 479 were excluded after title/abstract/full-text screening. Three further studies were included from the references of eligible studies and from discussions with subject matter experts, resulting in 11 included studies. The JBI checklist indicated six studies scored ≥7 points and four studies ≥4 points. Pooled data revealed collared stems had significantly lower revision rates (OR = 0.45; 95% CI = 0.31-0.64) and subsidence (MD = -1 mm; 95% CI = -1.6--0.3), but no significant difference in intraoperative complication rates (OR = 0.94; 95% CI = 0.67-1.32) in the short term to mid-term. Unpooled data indicated that collared stems provide equivalent survival, equivalent or better outcomes, and equivalent or lower complication rates.

Conclusion

In comparative studies, collared stems have lower revision rates than collarless stems, as well as equivalent or better clinical and radiographic outcomes. Differences could be due to a protective effect that the collar offers against subsidence, particularly in undersized or misaligned stems. Further studies are warranted to confirm long-term results and better understand differences between registry data and clinical studies.

Effect of femoral stem surface coating on clinical and radiographic outcomes of cementless primary total hip arthroplasty: a patient-matched retrospective study

PURPOSE

This study aims to determine whether changing the stem coating grants superior outcomes at a minimum follow-up of five years.

METHODS

Retrospective review of a consecutive series of primary total hip arthroplasties (THAs) operated by direct anterior approach between 01/01/2013 and 31/12/2014. Two stems were compared, which were identical except for their surface coating; "the Original stem" was fully coated with hydroxyapatite (HA), while "the ProxCoat stem" was proximally coated with plasma-sprayed titanium and HA. Matching was performed. Clinical assessment included modified Harris hip score (mHHS), Oxford hip score (OHS), and forgotten joint score (FJS). Radiographic assessment evaluated alignment, subsidence, pedestal formation, heterotopic ossification, radiolucent lines ≥ 2 mm, spot welds, cortical hypertrophy, and osteolysis.

RESULTS

232 hips received the Original stem and 167 the ProxCoat stem, from which respectively five hips (2.2%) and no hips (0%) underwent revision. Matching identified two groups of 91 patients, with comparable patient demographics. At > five years follow-up, there were no differences in OHS (16 ± 6 vs 15 ± 5; p = 0.075) nor FJS (81 ± 26 vs 84 ± 22; p = 0.521), but there were differences in mHHS (89 ± 15 vs 92 ± 12; p = 0.042). There were no differences in alignment, subsidence, pedestal formation, heterotopic ossification, cortical hypertrophy, and osteolysis. There were differences in prevalence of proximal radiolucent lines (12% vs 0%; p < 0.001) and distal spot welds (24% vs 54%; p < 0.001).

CONCLUSION

At a minimum follow-up of five years, this study on matched patients undergoing primary THA found that ProxCoat stems results in significantly fewer radiolucent lines, more spot welds, and less revisions than Original stems, thus suggesting better bone ingrowth.

Evaluation of the Cathodic Electrodeposition Effectiveness of the Hydroxyapatite Layer Used in Surface Modification of Ti6Al4V-Based Biomaterials

The important issue associated with the design and the fabrication of the titanium and titanium alloy implants is the increase of their biointegration with bone tissue. In the presented paper, the research results concerning the conditions used in the cathodic deposition of hydroxyapatite on the surface Ti6Al4V substrates primarily modified by the production of TiO₂ nanoporous coatings, TiO₂ nanofibers, and titanate coatings, are discussed. Despite excellent biocompatibility with natural bone tissue of materials based on hydroxyapatite (HA), their poor adhesion to the substrate caused the limited use in the implants' construction. In our works, we have focused on the comparison of the structure, physicochemical, and mechanical properties of coating systems produced at different conditions. For this purpose, scanning electron microscopy images, chemical composition, X-ray diffraction patterns, infrared spectroscopy, wettability, and mechanical properties are analyzed. Our investigations proved that the intermediate titanium oxide coatings presence significantly increases the adhesion between the hydroxyapatite layer and the Ti6Al4V substrate, thus solving the temporary delamination problems of the HA layer.

Graphene Nanocoating: High Quality and Stability upon Several Stressors

Titanium implants present 2 major drawbacks-namely, the long time needed for osseointegration and the lack of inherent antimicrobial properties. Surface modifications and coatings to improve biomaterials can lose their integrity and biological potential when exposed to stressful microenvironments. Graphene nanocoating (GN) can be deposited onto actual-size dental and orthopedic implants. It has antiadhesive properties and can enhance bone formation in vivo. However, its ability to maintain structural integrity and quality when challenged by biologically relevant stresses remains largely unknown. GN was produced by chemical vapor deposition and transferred to titanium via a polymer-assisted transfer technique. GN has high inertness and did not increase expression of inflammatory markers by macrophages, even in the presence of lipopolysaccharides. It kept high coverage at the top tercile of tapered dental implant collars after installation and removal from bone substitute and pig maxilla. It also resisted microbiologically influenced corrosion, and it maintained very high coverage area and quality after prolonged exposure to biofilms and their removal by different techniques. Our findings show that GN is unresponsive to harsh and inflammatory environments and that it maintains a promising level of structural integrity on the top tercile of dental implant collars, which is the area highly affected by biofilms during the onset of implant diseases. Our findings open the avenues for the clinical studies required for the use of GN in the development of implants that have higher osteogenic potential and are less prone to implant diseases.