The Effects of Oxygen Functional Groups on Graphene Oxide on the Efficient Adsorption of Radioactive Iodine

Physicochemical Treatments of Graphene Oxide to Improve Water Vapor/Gas Separation Performance of Supported Laminar Membranes: Sonication and H2O2 Oxidation

We investigated the previously unexplored domain of water vapor/gas separation using graphene oxide (GO) membranes, expecting future applications, including gas dehumidifiers and superior humidity controllers. While the importance of manipulation of GO nanosheet size and surface chemistry in traditional water purification and gas separation has been acknowledged, their potential impact on water vapor/gas separation remained unexplored until now. We applied sonication and hydrogen peroxide treatments to GO water dispersions and systematically evaluated the size and surface chemistry of each GO nanosheet. Both treatments reduced the GO nanosheet size to shorten the diffusion length, which improved water permeance. In addition, hydrogen peroxide treatment improved the hydrophilicity of the nanosheet. Our novel findings demonstrate that optimization of GO nanosheet size and the increase in their hydrophilicity via hydrogen peroxide treatments for 5 h significantly enhance water permeance, leading to a remarkable water vapor permeance of 4.6 × 10-6 mol/(m2 s Pa) at 80 °C, a 3.1-fold improvement over original GO membranes, while maintaining a water vapor/nitrogen permeance ratio exceeding 10,000. These results not only provide important insights into the nature of water vapor/gas separation but also suggest innovative methods for optimizing the GO membrane structure.

Impact of Iodine Electrodeposition on Nanoporous Carbon Electrode Determined by EQCM, XPS and In Situ Raman Spectroscopy

The charging of nanoporous carbon via electrodeposition of solid iodine from iodide-based electrolyte is an efficient and ecofriendly method to produce battery cathodes. Here, the interactions at the carbon/iodine interface from first contact with the aqueous electrolyte to the electrochemical polarization conditions in a hybrid cell are investigated by a combination of in situ and ex situ methods. EQCM investigations confirm the flushing out of water from the pores during iodine formation at the positive electrode. XPS of the carbon surface shows irreversible oxidation at the initial electrolyte immersion and to a larger extent during the first few charge/discharge cycles. This leads to the creation of functional groups at the surface while further reactive sites are consumed by iodine, causing a kind of passivation during a stable cycling regime. Two sources of carbon electrode structural modifications during iodine formation in the nanopores have been revealed by in situ Raman spectroscopy, (i) charge transfer and (ii) mechanical strain, both causing reversible changes and thus preventing performance deterioration during the long-term cycling of energy storage devices that use iodine-charged carbon electrodes.

A Study of Methylene Blue Dye Interaction and Adsorption by Monolayer Graphene Oxide

The graphene oxide (GO) interaction with methylene blue (MB) cationic dye was studied in an aqueous solution at different pH during MB adsorption. The mutual interaction of MB with GO surface was studied and evaluated by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The π-π and electrostatic interaction of MB with GO surface are the main types of interactions, and the XRD data show the monomeric arrangement of MB cation with GO. The GO surface functional groups and point of zero charge (PZC) were determined by acid-base titration. Suitability of zeta-potential measurement and acid-base titration method was briefly discussed. The quality of prepared GO was evaluated by Raman spectroscopy, XRD, and atomic force microscope (AFM). The experimental adsorption equilibrium data were analyzed using Langmuir, Langmuir-Freundlich, Freundlich, and Temkin isotherms. The GO maximum adsorption capacity increases with higher pH, that is ascribed to the facile interaction of negatively charged GO with positively charged MB structure.

Dispersive micro-solid phase extraction with a magnetic nanocomposite followed by electrothermal atomic absorption measurement for the speciation of thallium

A magnetic dispersive micro-solid phase extraction procedure for the determination of the thallium content in waters is presented. The incorporation in the sample (10 mL) of a small amount of graphene-Fe₃O₄ composite (3.6 mg) in the presence of 10^-4 mol L^-1 Aliquat 336 at pH 2 results in the complete retention of both thallium(I) and thallium(III). After separation with a magnet, the micro-solid phase recovered is treated with 0.05 mL of a 0.1 mol L^-1 sodium ethylenediaminetetracetate solution at pH 9, and the supernatant obtained after application of the magnet is introduced in the electrothermal atomizer of an atomic absorption spectrometer to obtain the signal corresponding to the total thallium content. For speciation, the trivalent form in a second sample aliquot is separated by means of a liquid-liquid extraction stage with chloroform and methyl trioctyl ammonium in the presence of bromide, and the signal corresponding to the monovalent form is obtained, the concentration of thallium(III) being obtained by difference. The enrichment factor is 185, which permits a detection limit as low as 0.01 μg L^-1 of the analyte to be achieved. The relative standard deviation for five measurements at the 0.1 μg L^-1 thallium level is below 5%. The reliability of the procedure is verified by analysing five certified reference samples for which speciation data are also given.