Application of Selective Induction Heating for Improvement of Mechanical Properties of Elastic Hinges

Internal Gas-Assisted Mold Temperature Control for Improving the Filling Ability of Polyamide 6 + 30% Glass Fiber in the Micro-Injection Molding Process

In micro-injection molding, the plastic filling in the cavity is limited by the frozen layer due to the rapid cooling of the hot melt when it comes into contact with the surface of the cavity at a lower temperature. This problem is more serious with composite materials, which have a higher viscosity than pure materials. Moreover, this issue is also more serious with composite materials that have a higher weight percentage of glass filer. In this article, a pre-heating step with the internal gas heating method was used to heat the cavity surface to a high temperature before the filling step to reduce the frozen layer and to improve the filling ability of the composite material (polyamide 6 + 30% glass fiber) in the micro-injection molding process. To heat the cavity surface, an internal gas-assisted mold temperature control (In-GMTC) system was used with a pulsed cooling system. We assessed different mold insert thicknesses (t) and gaps between the gas gate and the heating surface (G) to achieve rapid mold surface temperature control. The heating process was observed using an infrared camera, and the temperature distribution and the heating rate were analyzed. Thereafter, along with the local temperature control, the In-GMTC was used for the micro-injection molding cycle. The results show that, with a gas temperature of 300 °C and a gas gap of 3.5 mm, the heating rate reached 8.6 °C/s. The In-GMTC was also applied to the micro-injection molding process with a part thickness of 0.2 mm. It was shown that the melt flow length had to reach 24 mm to fill the cavity completely. The results show that the filling ability of the composite material increased from 65.4% to 100% with local heating at the melt inlet area when the gas temperature rose from 200 to 400 °C with a 20 s heating cycle.

Investigation of the Strength of Plastic Parts Improved with Selective Induction Heating

The use of selective induction heating of molding surfaces allows for better filling of molding cavities and has a positive effect on the properties of molded products. This is particularly important in the production of parts that include flexible hinges, which are thin plastic layers connecting two or more parts of the product. By using hinges, it is possible to expand the use of injection molding products and their capabilities. They are widely used in the production of parts for the electrical engineering industry and for packaging Fast Moving Consumer Goods (FMCG). The use of hinges also entails specific reductions in wall thickness. Increases in the shear rate can be expected, which can lead to the degradation of polymers and deterioration of mechanical properties of materials. This paper investigates injection molded flexible hinge parts manufactured with selective induction heating to improve their properties. To verify the efficiency of reduction of material degradation due to high shear rates, open/close tests of elastic hinges were performed. The linear relation between the number of cycles the hinges can withstand, mold temperature and injection time was identified, where mold temperature was the more significant factor.

Design and Simulation Study of the Induction Heated Injection Mold with Sliders

In order to increase the quality of the products manufactured by injection molding, RTC technology can be used to achieve higher mold temperatures. As a result, the path of the injected melt can be extended, allowing the production of parts with more complex shapes and greater length. Induction heating allows heating only selected forming surfaces of the mold which increases the speed and efficiency of the process. This paper presents the concept of a detachable inductor integrated with sliders to enable the application of this technology in an injection mold with sliders, along with the theoretical model used to perform the tests. First, the effect of the magnetic concentrator shape on the process was analyzed. This was followed by a simulation study of the influence of process parameters: heating time, frequency, and electric current. An extensive analysis of the test results of the temperature distribution on the insert allowed for the selection of parameter sets that would enable obtaining the desired surface temperature without a major increase in process time. The results of simulation studies confirm the possible applications and present the range of parameters for obtaining the optimal process.

Improving the Melt Flow Length of Acrylonitrile Butadiene Styrene in Thin-Wall Injection Molding by External Induction Heating with the Assistance of a Rotation Device

In injection molding, the temperature control of the dynamic mold is an excellent method for improving the melt flow length, especially of thin-wall products. In this study, the heating efficiency of a novel heating strategy based on induction heating was estimated. With the use of this heating strategy, a molding cycle time similar to the traditional injection molding process could be maintained. In addition, this strategy makes it easier to carry out the heating step due to the separation of the heating position and the mold structure as well as allowing the ease of magnetic control. The results show that, with an initial mold temperature of 30 °C and a gap (G) between the heating surface and the inductor coil of 5 mm, the magnetic heating process can heat the plate to 290 °C within 5 s. However, with a gap of 15 mm, it took up to 8 s to reach 270 °C. According to the measurement results, when the mold heating time during the molding process increased from 0 to 5 s, the flow length increased significantly from 71.5 to 168.1 mm, and the filling percentage of the thin-wall product also increased from 10.2% to 100%. In general, the application of external induction heating (Ex-IH) during the molding cycle resulted in improved melt flow length with minimal increase in the total cycle time, which remained similar to that of the traditional case.