|
1
|
Guan H, Lv C, Ding Q, Wang G, Xiong N, Zhou Z. The Effect of Cr Addition on the Strength and High Temperature Oxidation Resistance of Y 2O 3 Dispersion Strengthened Mo Composites. MATERIALS (BASEL, SWITZERLAND) 2024; 17:2550. [PMID: 38893814 PMCID: PMC11173634 DOI: 10.3390/ma17112550] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/17/2024] [Revised: 05/15/2024] [Accepted: 05/22/2024] [Indexed: 06/21/2024]
Abstract
Y2O3 dispersion-strengthened Molybdenum (Mo) composites were prepared by the mechanical alloying of Mo and Y powders then consolidation by spark plasma sintering. The effects of Chromium (Cr) addition (0 wt. %, 5 wt. %, 10 wt. % and 15 wt. %, respectively) on the mechanical performance and high-temperature oxidation resistance of Mo-Y2O3 were investigated. The introduction of Cr had a significant influence on the mechanical property and oxidation resistance of the Mo-Y2O3 composite. The highest bending strength reached 932 MPa when the addition of Cr content was 5 wt. % (Mo-5Cr-1Y sample). This improvement is likely attributable to the dual mechanism of grain refinement and solid solution strengthening. Moreover, the Mo-5Cr-1Y sample showed the thinnest oxide layer thickness after high-temperature oxidation tests, and exhibited the best oxidation resistance performance compared with the other samples. First principle calculation reveals that Cr could improve the Mo-MoO3 interface bonding to prevent rapid spalling of the oxide layer. Meanwhile, Cr also facilitates the formation of the dense Cr2(MoO4)3 layer on the surface, which can inhibit further oxidation.
Collapse
Affiliation(s)
- Haochen Guan
- School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
| | - Chongshan Lv
- School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
| | - Qingming Ding
- School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
| | - Guangda Wang
- Advanced Technology & Materials Co., Ltd., Beijing 100081, China
| | - Ning Xiong
- Advanced Technology & Materials Co., Ltd., Beijing 100081, China
| | - Zhangjian Zhou
- School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
- State Key Laboratory of Nuclear Power Safety Technology and Equipment, University of Science and Technology Beijing, Beijing 100083, China
| |
Collapse
|
|
2
|
Fang XQ, Wang JB, Liu SY, Wen JZ, Song HY, Liu HT. Microstructure Evolution, Hot Deformation Behavior and Processing Maps of an FeCrAl Alloy. MATERIALS (BASEL, SWITZERLAND) 2024; 17:1847. [PMID: 38673206 PMCID: PMC11051250 DOI: 10.3390/ma17081847] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/25/2024] [Revised: 04/11/2024] [Accepted: 04/13/2024] [Indexed: 04/28/2024]
Abstract
The deteriorated plasticity arising from the insoluble precipitates may lead to cracks during the rolling of FeCrAl alloys. The microstructure evolution and hot deformation behavior of an FeCrAl alloy were investigated in the temperature range of 750-1200 °C and strain rate range of 0.01-10 s-1. The flow stress of the FeCrAl alloy decreased with an increasing deformation temperature and decreased strain rate during hot working. The thermal deformation activation energy was determined to be 329.49 kJ/mol based on the compression test. Then, the optimal hot working range was given based on the established hot processing maps. The hot processing map revealed four small instability zones. The optimal working range for the material was identified as follows: at a true strain of 0.69, the deformation temperature should be 1050-1200 °C, and the strain rate should be 0.01-0.4 s-1. The observation of key samples of thermally simulated compression showed that discontinuous dynamic recrystallization started to occur with the temperate above 1000 °C, leading to bended grain boundaries. When the temperature was increased to 1150 °C, the dynamic recrystallization resulted in a microstructure composed of fine and equiaxed grains.
Collapse
Affiliation(s)
- Xiang-Qian Fang
- State Key Laboratory of Rolling and Automation, School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China; (X.-Q.F.); (J.-B.W.)
| | - Jin-Bin Wang
- State Key Laboratory of Rolling and Automation, School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China; (X.-Q.F.); (J.-B.W.)
| | - Si-You Liu
- School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China; (S.-Y.L.); (J.-Z.W.)
| | - Jun-Zhe Wen
- School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China; (S.-Y.L.); (J.-Z.W.)
| | - Hong-Yu Song
- State Key Laboratory of Rolling and Automation, School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China; (X.-Q.F.); (J.-B.W.)
| | - Hai-Tao Liu
- State Key Laboratory of Rolling and Automation, School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China; (X.-Q.F.); (J.-B.W.)
| |
Collapse
|
|
3
|
Tao L, Yang Y, Zhu W, Sun J, Wu J, Xu H, Yan L, Yang A, Xu Z. Stress Distribution in Wear Analysis of Nano-Y 2O 3 Dispersion Strengthened Ni-Based μm-WC Composite Material Laser Coating. MATERIALS (BASEL, SWITZERLAND) 2023; 17:121. [PMID: 38203975 PMCID: PMC10780224 DOI: 10.3390/ma17010121] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/13/2023] [Revised: 12/20/2023] [Accepted: 12/22/2023] [Indexed: 01/12/2024]
Abstract
Oxide-dispersion- and hard-particle-strengthened (ODS) laser-cladded single-layer multi-tracks with a Ni-based alloy composition with 20 wt.% μm-WC particles and 1.2 wt.% nano-Y2O3 addition were produced on ultra-high-strength steel in this study. The investigation of the composite coating designed in this study focused on the reciprocating friction and wear workpiece surface under heavy load conditions. The coating specimens were divided into four groups: (i) Ni-based alloy, nano-Y2O3, and 2 μm-WC (2 μm WC-Y/Ni); (ii) Ni-based alloy with added 2 μm-WC (2 μmWC/Ni); (iii) Ni-based alloy with added 80 μm-WC (80 μmWC/Ni); and (iv) base metal ultra-high-strength alloy steel 30CrMnSiNi2A. Four conclusions were reached: (1) Nano-Y2O3 could effectively inhibit the dissolution of 2 μm-WC. (2) It can be seen from the semi-space dimensionless simulation results that the von Mises stress distribution of the metal laser composite coating prepared with a 2 μm-WC particle additive was very uniform and it had better resistance to normal impact and tangential loads than the laser coating prepared with the 80 μm-WC particle additive. (3) The inherent WC initial crack and dense stress concentration in the 80 μm-WC laser coating could easily cause dislocations to accumulate, as shown both quantitatively and qualitatively, resulting in the formation of micro-crack nucleation. After the end of the running-in phase, the COF of the 2 μm-WC-Y2O3/Ni component samples stabilized at the minimum of the COF of the four samples. The numerical order of the four COF curves was stable from small to large as follows: 2 μm-WC-Y2O3/Ni, 2 μm-WC/Ni, 80 μm-WC/Ni, and 30CrMnSiNi2A. (4) The frictional volume loss rate of 2 μm-WC-Y2O3/Ni was 1.3, which was significantly lower than the corresponding values of the other three components: 2.4, 3.5, and 13.
Collapse
Affiliation(s)
- Li Tao
- Department of Robot Engineering, School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang 222005, China; (L.T.); (Y.Y.); (W.Z.); (J.W.); (H.X.); (L.Y.); (A.Y.); (Z.X.)
| | - Yang Yang
- Department of Robot Engineering, School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang 222005, China; (L.T.); (Y.Y.); (W.Z.); (J.W.); (H.X.); (L.Y.); (A.Y.); (Z.X.)
| | - Wenliang Zhu
- Department of Robot Engineering, School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang 222005, China; (L.T.); (Y.Y.); (W.Z.); (J.W.); (H.X.); (L.Y.); (A.Y.); (Z.X.)
| | - Jian Sun
- School of Mechanical and Electrical Engineering, Xi’an Polytechnic University, Xi’an 710048, China
| | - Jiale Wu
- Department of Robot Engineering, School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang 222005, China; (L.T.); (Y.Y.); (W.Z.); (J.W.); (H.X.); (L.Y.); (A.Y.); (Z.X.)
| | - Hao Xu
- Department of Robot Engineering, School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang 222005, China; (L.T.); (Y.Y.); (W.Z.); (J.W.); (H.X.); (L.Y.); (A.Y.); (Z.X.)
| | - Lu Yan
- Department of Robot Engineering, School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang 222005, China; (L.T.); (Y.Y.); (W.Z.); (J.W.); (H.X.); (L.Y.); (A.Y.); (Z.X.)
| | - Anhui Yang
- Department of Robot Engineering, School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang 222005, China; (L.T.); (Y.Y.); (W.Z.); (J.W.); (H.X.); (L.Y.); (A.Y.); (Z.X.)
| | - Zhilong Xu
- Department of Robot Engineering, School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang 222005, China; (L.T.); (Y.Y.); (W.Z.); (J.W.); (H.X.); (L.Y.); (A.Y.); (Z.X.)
| |
Collapse
|