Coal Fly Ash Derived Silica Nanomaterial for MMMs-Application in CO2/CH4 Separation

Characterization of Silicate Glass/Mullite Composites Based on Coal Fly Ash Cenospheres as Effective Gas Separation Membranes

Membrane technology is a promising method for gas separation. Due to its low energy consumption, environmental safety, and ease of operation, membrane separation has a distinct advantage over the cryogenic distillation conventionally used to capture light inert gases. For efficient gas recovery and purification, membrane materials should be highly selective, highly permeable, thermally stable, and low-cost. Currently, many studies are focused on the development of high-tech materials with specific properties using industrial waste. One of the promising waste products that can be recycled into membrane materials with improved microstructure is cenospheres-hollow aluminosilicate spherical particles that are formed in fly ash from coal combustion during power generation. For this purpose, based on narrow fractions of fly ash cenospheres containing single-ring and network structure globules, silicate glass/mullite composites were prepared, characterized, and tested for helium-neon mixture separation. The results indicate that the fragmented structure of the cenosphere shells with areas enriched in SiO2 without modifier oxides, formed due to the crystallization of defective phases of mullite, quartz, cristobalite, and anorthite, significantly facilitates the gas transport process. The permeability coefficients He and Ne exceed similar values for silicate glasses; the selectivity corresponds to a high level even at a high temperature: αHe/Ne-22 and 174 at 280 °C.

End-Of-Use Fly Ash as an Effective Reinforcing Filler in Green Polymer Composites

The aim of this study is to use fly ash powder in an environmentally friendly matrix, in a novel way, addressing environmental and disposal problems. Fly ash/epoxy composites were prepared and studied varying the filler content. An investigation of structural and morphological characteristics was conducted using of X-ray diffraction patterns and scanning electron microscopy images, which revealed the successful fabrication of composites. Thermomechanical properties were studied via dynamic mechanical analysis and static mechanical tests. The composites exhibited an improved mechanical response. Broadband dielectric spectroscopy was used to investigate the dielectric response of the composite systems over the frequency range from 10-1 to 107 Hz and the temperature range from 30 to 160 °C. The analysis revealed the presence of three relaxation processes in the spectra of the tested systems. Interfacial polarization, the glass-to-rubber transition of the polymer matrix, and the rearrangement of polar side groups along the polymer chain are the processes that occur under a descending relaxation time. It was found that dielectric permittivity increases with filler content. Finally, the influence of filler content and the applied voltage under dc conditions was analyzed to determine the ability of the composites to store and retrieve electric energy. Fly ash improved the efficiency of the storing/retrieving energy of the composites.

A green and multi-win strategy for coal fly ash disposal by CO2 fixation and mesoporous silica synthesis

Coal combustion provides plenty of energy, along with enormous coal fly ash (CFA) and CO₂ emission. CFA could be recycled for mesoporous silica synthesis, but expensive templates are usually needed. In this work, we proposed a multi-win strategy using CO₂ as the precipitator and template. Mesoporous silica powders, with a maximum specific surface area of 355.45 m²/g, a pore volume of 0.73 cm³/g, and an average pore size of around 7.67 nm, were synthesized. The influences of silicon concentration, CO₂ flow rate, and ultrasound were investigated. In addition, the Na₂CO₃ by-product was produced with a purity of over 92 %. By averagely calculating, 1 ton CFA could generate 285 kg mesoporous silica and 1.02 t crude Na₂CO₃. Around 433 kg of CO₂ could be absorbed. Therefore, multi-goals of CFA disposal, CO₂ storage, and valuable silica materials production were realized, and the study could pave the way for large-scale industrial applications.

Chitosan-sEPDM and Melatonin-Chitosan-sEPDM Composite Membranes for Melatonin Transport and Release

Melatonin is the hormone that focuses the attention of the researchers in the medical, pharmaceutical, materials, and membranes fields due to its multiple biomedical implications. The variety of techniques and methods for the controlled release of melatonin is linked to the multitude of applications, among which sports medicine occupies a special place. This paper presents the preparation and characterization of composite membranes based on chitosan (Chi) and sulfonated ethylene-propylene-diene terpolymer (sEPDM). The membranes were obtained by controlled vacuum evaporation from an 8% sEPDM solution in toluene (w/w), in which chitosan was dispersed in an ultrasonic field (sEPDM:Chi = 1:1, w/w). For the comparative evaluation of the membranes' performances, a melatonin-chitosan-sulfonated ethylene-propylene-diene terpolymer (Mel:Chi:sEPDM = 0.5:0.5:1.0, w/w/w) test membrane was made. The prepared membranes were morphologically and structurally characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), energy-dispersive spectroscopy analysis (EDAX), thermal analysis (TG, DSC), thermal analysis coupled with chromatography and infrared analysis, and contact angle measurements, but also from the point of view of performance in the process of transport and release of melatonin in dedicated environments (aqueous solutions with controlled pH and salinity). The prepared membranes can release melatonin in amounts between 0.4 mg/cm²·per day (sEPDM), 1.6 mg/ cm²·per day (Chi/sEPDM), and 1.25 mg/cm²·per day (Mel/Chi/SEPDM).

Potential innovation against Alzheimer's disorder: a tricomponent combination of natural antioxidants (vitamin E, quercetin, and basil oil) and the development of its intranasal delivery

Alzheimer's disorder (AD) is very difficult to manage and treat. The complexity of the brain, the blood-brain barrier influencing a multitude of parameters/biomarkers, as well as numerous other factors involved often contribute to the decline in the chances of treatment success. Development of the new drug moiety also takes time, being necessary to consider both its toxicity and related issues. As a strategic plan, a combined strategy is being developed and considered to address AD pathology using several approaches. A combination of vitamin E, quercetin, and basil oil in a nano-based formulation is designed to be administered nasally. The antioxidant present in these natural-based products helps to treat and alleviate AD if a synergistic approach is considered. The three active substances mentioned above are well known for the treatment of neurodegenerative disorders. The nanoformulation helps the co-delivery of the drug moiety to the brain through the intranasal route. In this review, a correlation and use of vitamin E, quercetin, and basil oil in a nano-based formulation is described as an effective way to treat AD. The intranasal administration of drugs is a promising approach for the treatment of neurodegenerative and mental disorders, as this route is non-invasive, enhances the bioavailability, allows a drug dose reduction, bypasses the blood-brain barrier, and reduces the systemic undesired effect. The use of natural products is generally considered to be just as safe; therefore, by using this combined approach, the level of toxicity can be minimized.

Analysis of Influencing Factors on the Gas Separation Performance of Carbon Molecular Sieve Membrane Using Machine Learning Technique

Gas separation performance of the carbon molecular sieve (CMS) membrane is influenced by multiple factors including the microstructural characteristics of carbon and gas properties. In this work, the support vector regression (SVR) method as a machine learning technique was applied to the correlation between the gas separation performance, the multiple membrane structure, and gas characteristic factors of the self-manufactured CMS membrane. A simple quantitative index based on the Robeson’s upper bound line, which indicated the gas permeability and selectivity simultaneously, was proposed to measure the gas separation performance of CMS membrane. Based on the calculation results, the inferred key factors affecting the gas permeability of CMS membrane were the fractional free volume (FFV) of the precursor, the average interlayer spacing of graphite-like carbon sheet, and the final carbonization temperature. Moreover, the most influential factors for the gas separation performance were supposed to be the two structural factors of precursor influencing the porosity of CMS membrane, the carbon residue and the FFV, and the ratio of the gas kinetic diameters. The results would be helpful to the structural optimization and the separation performance improvement of CMS membrane.

Improvement of Pavement Subgrade by Adding Cement and Fly Ash to Natural Desert Sand

Soil characteristics are paramount to design pavements and to assess the economic viability of a road. In the desert, such as that found in southern Libya, the very poor quality of soils leads to important pavement distress such as cracks, rutting, potholes, and lateral shear failure on the edges. To improve the strength of desert sand, an innovative approach is proposed, consisting of adding manufactured sand, ordinary Portland cement (OPC), and fly ash (FA) as a binder. OPC and FA improve the characteristics of mixes of crushed fine aggregate (CFA) and natural desert sand (NDS). These results are based on a gradation of two sand sources to determine the particle distribution and X-ray fluorescence (XRF) to determine their chemical and physical properties, respectively. This research assesses the effect of cement and fly ash on the geotechnical behavior of two mixtures of fine desert and manufactured sands (30:70% and 50:50%). The mix composed of 26% of CFA, 62% of NDS, 5% of OPC, and 7% of FA shows optimal results in terms of strength, compaction, and bearing capacity characteristics.

Understanding the Adsorption Capacity for CO2 in Reduced Graphene Oxide (rGO) and Modified Ones with Different Heteroatoms in Relation to Surface and Textural Characteristics

Reduced graphene oxide is a material that has a variety of applications, especially in CO2 adsorption. The study of this research is the preparation of reduced graphene oxide with different heteroatoms and how the adsorption capacity is changed. The functionalization with other compounds bearing Si, S, N, and O was before reducing graphene oxide. Different monoliths were prepared by changing the ascorbic acid analogy and the temperature of reduction. The different porosity values, percentages of heteroatoms, and synthetic parameters show that the adsorption capacity is a complex procedure that can be affected by multiple parameters. Microporosity, different functionalities from heteroatoms, and high surface/volume of pores are the significant parameters that affect adsorption. All parameters should establish a balance among all parameters to achieve high adsorption of CO2.

Current Trends in Advanced Alginate-Based Wound Dressings for Chronic Wounds

Chronic wounds represent a major public health issue, with an extremely high cost worldwide. In healthy individuals, the wound healing process takes place in different stages: inflammation, cell proliferation (fibroblasts and keratinocytes of the dermis), and finally remodeling of the extracellular matrix (equilibrium between metalloproteinases and their inhibitors). In chronic wounds, the chronic inflammation favors exudate persistence and bacterial film has a special importance in the dynamics of chronic inflammation in wounds that do not heal. Recent advances in biopolymer-based materials for wound healing highlight the performance of specific alginate forms. An ideal wound dressing should be adherent to the wound surface and not to the wound bed, it should also be non-antigenic, biocompatible, semi-permeable, biodegradable, elastic but resistant, and cost-effective. It has to give protection against bacterial, infectious, mechanical, and thermal agents, to modulate the level of wound moisture, and to entrap and deliver drugs or other molecules This paper explores the roles of alginates in advanced wound-dressing forms with a particular emphasis on hydrogels, nanofibers networks, 3D-scaffolds or sponges entrapping fibroblasts, keratinocytes, or drugs to be released on the wound-bed. The latest research reports are presented and supported with in vitro and in vivo studies from the current literature.

Enthalpies of Immersion in Caffeine and Glyphosate Aqueous Solutions of SBA-15 and Amino-Functionalized SBA-15

Mesostructured silica SBA-15 and amino-functionalized silica SBA-15-NH₂ were synthesized, and then, characterization, adsorption capacity, and immersion enthalpies in caffeine and glyphosate on SBA-15 and SBA-15-NH₂ were evaluated. The enthalpy parameter was determined using a local construction Tian-type heat conduction calorimeter. Calorimetric studies in caffeine solutions exhibit negative enthalpy values; exothermic process characteristics for SBA-15 were between -13.90 and -194.06 J g^-1 and those for SBA-15-NH₂ were between -7.22 and -60.34 J g^-1, and the adsorption capacity of caffeine was better in SBA-15 than that in SBA-15-NH₂. In contrast, the enthalpies of immersion in glyphosate solutions were -5.06 to -56.2 J g^-1 and the immersion of SBA-15-NH₂ in each solution generated enthalpy values of -9.06 to -41.2 J g^-1, but the adsorption capacity of glyphosate was better in the amino-functionalized SBA-15. The results show that functionalization of SBA-15 produced differences in physicochemical characteristics of solids, since energy and affinity for the calorimetric liquids are related to the surface properties of solids as well as the chemical nature of the target molecule, immersion enthalpy, was different.

Kidney-Protector Lipidic Cilastatin Derivatives as Structure-Directing Agents for the Synthesis of Mesoporous Silica Nanoparticles for Drug Delivery

Mesoporous silica nanomaterials have emerged as promising vehicles in controlled drug delivery systems due to their ability to selectively transport, protect, and release pharmaceuticals in a controlled and sustained manner. One drawback of these drug delivery systems is their preparation procedure that usually requires several steps including the removal of the structure-directing agent (surfactant) and the later loading of the drug into the porous structure. Herein, we describe the preparation of mesoporous silica nanoparticles, as drug delivery systems from structure-directing agents based on the kidney-protector drug cilastatin in a simple, fast, and one-step process. The concept of drug-structure-directing agent (DSDA) allows the use of lipidic derivatives of cilastatin to direct the successful formation of mesoporous silica nanoparticles (MSNs). The inherent pharmacological activity of the surfactant DSDA cilastatin-based template permits that the MSNs can be directly employed as drug delivery nanocarriers, without the need of extra steps. MSNs thus synthesized have shown good sphericity and remarkable textural properties. The size of the nanoparticles can be adjusted by simply selecting the stirring speed, time, and aging temperature during the synthesis procedure. Moreover, the release experiments performed on these materials afforded a slow and sustained drug release over several days, which illustrates the MSNs potential utility as drug delivery system for the cilastatin cargo kidney protector. While most nanotechnology strategies focused on combating the different illnesses this methodology emphasizes on reducing the kidney toxicity associated to cancer chemotherapy.

Improvement of Recycled Aggregates Properties by Means of CO2 Uptake

Concrete from deconstruction can have a second life in the form of recycled concrete aggregates (RCAs). They unfortunately have poor properties (high porosity and water absorption coefficient (WAC)) with respect to natural aggregates. Accelerated carbonation was implemented to improve the RCA properties and to increase their use by storing carbon dioxide (CO2) in the cement matrix and thereby reduce their environmental impact. This paper aims to perform a parametric study of a process for accelerated carbonation of RCAs to store the largest possible amount of CO2 and improve their properties. This study highlights the fact that each of these parameters affects CO2 storage, with an optimum water content for the maximum CO2 uptake depending on the nature and the source of the RCAs. This optimum is related to the RCA water absorption coefficient by a linear relationship. The results show that accelerated carbonation reduces the water absorption coefficient by as much as 67%. Finally, carbonation also decreases porosity, as observed by mercury intrusion porosimetry, by filling the capillary pores.

Turning Agricultural Wastes into Biomaterials: Assessing the Sustainability of Scenarios of Circular Valorization of Corn Cob in a Life-Cycle Perspective

Circular economy plays a key role in increasing the sustainability of the agricultural sector, given the countless possibilities of transforming crop residues and recycling precious resources. The maize cultivation process produces a significant amount of residual organic materials, commonly left on the field, as a soil conditioner and source of nutrients even if some parts, such as the cob, play a minor role in these actions. The solutions for the valorization of this remnant depend on economic and environmental factors and the evaluation of the environmental performances of the processes in a life-cycle perspective is important to compare the overall sustainability of the valorization alternatives, maximizing their environmental added value. This work reports the results of Life Cycle Analysis, from cradle-to-gate of corn cob valorized as a raw material in two scenarios: corn cob pellet and corn cob abrasive grits to use as blasting or finishing media. A comparative study has been performed with two products available on the market and with the same functions. The results show that cob-based products have lower impact than those currently used. The work provides indication for evaluating the benefits of turning agricultural wastes in natural-based materials and intends to promote circular economy processes in agriculture production.

Mini-Review: Potential of Diatom-Derived Silica for Biomedical Applications

Diatoms are unicellular eukaryotic microalgae widely distributed in aquatic environments, possessing a porous silica cell wall known as frustule. Diatom frustules are considered as a sustainable source for several industrial applications because of their high biocompatibility and the easiness of surface functionalisation, which make frustules suitable for regenerative medicine and as drug carriers. Frustules are made of hydrated silica, and can be extracted and purified both from living and fossil diatoms using acid treatments or high temperatures. Biosilica frustules have proved to be suitable for biomedical applications, but, unfortunately, they are not officially recognised as safe by governmental food and medical agencies yet. In the present review, we highlight the frustule formation process, the most common purification techniques, as well as advantages and bottlenecks related to the employment of diatom-derived silica for medical purposes, suggesting possible solutions for a large-scale biosilica production.