Ionomers Based on Addition and Ring Opening Metathesis Polymerized 5-Phenyl-2-norbornene as a Membrane Material for Ionic Actuators

Effect of Electrode Morphology on Performance of Ionic Actuators Based on Vat Photopolymerized Membranes

Bucky gel electrodes are composed of morphology-determining polyvinylidene difluoride (PVDF) filled with carbon nanotubes (CNT). The electrodes are commonly fabricated via the casting of a CNT dispersion containing PVDF and ionic liquid. In this study, several pore-forming additives such as polyethylene glycol (PEG), dibutyl phthalate (DBP), and the common ionic liquid BMIMBF4 were used to control the morphology of the bucky gel electrodes. The crystalline phase type and content of PVDF in the electrodes were determined by FT-IR and DSC, respectively. SEM revealed a sponge-like structure in the case of the use of BMIMBF4 and a spherulite structure if PEG and DBP were used as additives. A strong influence of morphology on the anisotropic increase in the volume of electrodes upon impregnation with electrolyte was observed. The PEG-based electrode elongated more than the others, while the BMIMBF4-based electrode thickened to a greater extent. Ionic actuators were fabricated to experimentally reveal the effect of electrode morphology on their electromechanical efficiency. A high-precision vat photopolymerization technique was used to fabricate identical ionic membranes and minimize their influence on the properties of the actuators. The electrodes were characterized by the same porosity and electrical capacitance, while the actuators differ significantly in performance. As a result, a simple method of using pore-forming additives made it possible to increase the maximum deformation of bucky gel ionic actuators by 1.5 times by changing the morphology of the electrodes.

Synthesis and Characterization of Thiol-Functionalized Polynorbornene Dicarboximides for Heavy Metal Adsorption from Aqueous Solution

The contamination of water resources with heavy metals is a very serious concern that demands prompt and effective attention due to the serious health risks caused by these contaminants. The synthesis and ring-opening metathesis polymerization (ROMP) of norbornene dicarboximides bearing thiol pendant groups, specifically, N-4-thiophenyl-exo-norbornene-5,6-dicarboximide (1a), N-4-(methylthio)phenyl-exo-norbornene-5,6-dicarboximide (1b) and N-4-(trifluoromethylthio)phenyl-exo-norbornene-5,6-dicarboximide (1c), as well as their assessment for the removal of heavy metals from aqueous systems, is addressed in this work. The polymers were characterized by NMR, SEM and TGA, among others. Single and multicomponent aqueous solutions of Pb²⁺, Cd²⁺ and Ni²⁺ were employed to perform both kinetic and isothermal adsorption studies taking into account several experimental parameters, for instance, the initial metal concentration, the contact time and the mass of the polymer. In general, the adsorption kinetic data fit the pseudo-second-order model more efficiently, while the adsorption isotherms fit the Freundlich and Langmuir models. The maximum metal uptakes were 53.7 mg/g for Pb²⁺, 43.8 mg/g for Cd²⁺ and 29.1 mg/g for Ni²⁺ in the SH-bearing polymer 2a, 46.4 mg/g for Pb²⁺, 32.9 mg/g for Cd²⁺ and 27.1 mg/g for Ni²⁺ in the SCH₃-bearing polymer 2b and 40.3 mg/g for Pb²⁺, 35.9 mg/g for Cd²⁺ and 27.8 mg/g for Ni²⁺ in the SCF₃-bearing polymer 2c, correspondingly. The better performance of polymer 2a for the metal uptake was ascribed to the lower steric hindrance and higher hydrophilicity imparted by -SH groups to the polymer. The results show that these thiol-functionalized polymers are effective adsorbents of heavy metal ions from aqueous media.