Polymer Inclusion Membranes with P507-TBP Carriers for Lithium Extraction from Brines

Effective Transport Recovery of Palladium(II) from Hydrochloric Acid Solutions Using Polymer Inclusion Membrane with Tetrabutylammonium Bromide

This article reports on the extraction of palladium(II) from hydrochloric acid (HCl) solutions using polymer inclusion membranes (PIMs) containing tetrabutylammonium bromide (TBAB) as the ion carrier. The membranes were based on cellulose triacetate (CTA) as the polymer support. The main aim of this study is to determine the possibility of TBAB's application as the effective ion carrier/extractant of Pd(II) from hydrochloric acid solutions. At first, the effect of the hydrochloric acid concentration in the aqueous phase on palladium(II) extraction was investigated. Next, cellulose triacetate membranes with TBAB as the carrier were prepared and applied for the recovery of Pd(II) from HCl solutions. As a result of the investigations, the optimal composition of the receiving phase was determined to be 0.5 M thiourea in 0.1 M hydrochloric acid. The effect of the acid concentration in the source phase was investigated. The results show a linear decrease in the permeability coefficient and initial flux of palladium(II) with an increase in the hydrochloric acid concentration in the source phase. The separation of Pd(II) from Pt(IV) from the hydrochloric acid solution was also studied. The transport rate of Pd(II) was higher than Pt(IV). The separation coefficient SPd/Pt was 1.3. The results show that transport through PIMs with TBAB can be used as an effective method to recover Pd(II) from hydrochloric acid, especially at a low concentration of this acid.

Lithium-Ion-Sieve-Embedded Hybrid Membranes for Anion-Exchange- and Cation-Concentration-Driven Li/Mg Separation

There is an urgent need to develop efficient and environmentally friendly technologies for separating Li+ from brines containing abundant Mg2+ to meet the growing demand for lithium resources. In this work, we prepared hybrid membranes by integrating hydrogen manganese oxide (HMO), a lithium-ion sieve, as a filler into anion-exchange membranes (AEMs), the quaternary ammonium-functionalized poly(2,6-dimethyl-1,4-phenylene oxide) (QPPO) and poly(m-terphenyl piperidinium) (m-PTP). Cations are transported by electrostatic attraction originating from anions and the concentration difference across membranes. Because of the effects of electrostatic repulsion of the fixed cationic groups and steric resistance in AEMs, Li+ with less charge and smaller radius will preferentially pass through the membrane. In addition, the presence of HMO provides an additional fast transport channel for Li+, resulting in an enhanced Li+/Mg2+ separation performance. The results show that 20%HMO@m-PTP exhibits high Li+ flux (0.48 mol/m2·h) and Li+/Mg2+ selectivity (βLi+/Mg2+ = 14.1). Molecular dynamics simulations show that m-PTP has more free volume than QPPO, which is beneficial for rapid cation transport. Spectral analysis confirms the insertion and sieving of Li+ in HMO. This work illustrates the great potential of anion-exchange- and cation-concentration-driven hybrid membranes based on lithium-ion sieves for low-energy and efficient Li+ extraction processes.

The Latest Achievements of Liquid Membranes for Rare Earth Elements Recovery from Aqueous Solutions-A Mini Review

The systematic increase in the use of rare earth elements (REEs) in various technologically advanced products around the world (e.g., in electronic devices), the growing amount of waste generated by the use of high-tech materials, and the limited resources of naturally occurring REE ores resulted in an intensive search for effective and environmentally safe methods for recovering these elements. Among these methods, techniques based on the application of various types of liquid membranes (LMs) play an important role, primarily due to their high efficiency, the simplicity of membrane formation and use, the utilization of only small amounts of environmentally hazardous reagents, and the possibility of simultaneous extraction and back-extraction and reusing the membranes after regeneration. However, because both primary and secondary sources (e.g., waste) of REEs are usually complex and contain a wide variety of components, and the selectivity and efficiency of LMs depend on many factors (e.g., the composition and form of the membrane, nature of the recovered ions, composition of the feed and stripping phases, etc.), new membranes are being developed that are "tailored" to the properties of the recovered rare earth elements and to the character of the solution in which they occur. This review describes the latest achievements (since 2019) related to the recovery of a range of REEs with the use of various liquid membranes (supported liquid membranes (SLMs), emulsion liquid membranes (ELMs), and polymer inclusion membranes (PIMs)), with particular emphasis on methods that fall within the trend of eco-friendly solutions.

Comparison of Kinetic Models Applied for Transport Description in Polymer Inclusion Membranes

Five mathematical models for transport description in polymer inclusion membranes (PIMs) were presented and compared via regression analysis. The applicability of the models was estimated through the examination of experimental data of Zn(II), Cd(II), Pb(II), and Cu(II) ions transported by typical carriers. In four kinetic models, a change in the feed and stripping solution volume was taken into account. The goodness of fit was compared using the standard error of the regression, Akaike information criterion (AIC), Bayesian (Schwarz) information criterion (BIC), and Hannan-Quinn information criterion (HQC). The randomness distribution in the data was confirmed via a nonparametric runs test. Based on these quantities, appropriate models were selected.

The Use of Polymer Inclusion Membranes for the Removal of Metal Ions from Aqueous Solutions-The Latest Achievements and Potential Industrial Applications: A Review

The growing demand for environmentally friendly and economical methods of removing toxic metal ions from polluted waters and for the recovery of valuable noble metal ions from various types of waste, which are often treated as their secondary source, has resulted in increased interest in techniques based on the utilization of polymer inclusion membranes (PIMs). PIMs are characterized by many advantages (e.g., the possibility of simultaneous extraction and back extraction, excellent stability and high reusability), and can be adapted to the properties of the removed target analyte by appropriate selection of carriers, polymers and plasticizers used for their formulation. However, the selectivity and efficiency of the membrane process depends on many factors (e.g., membrane composition, nature of removed metal ions, composition of aqueous feed solution, etc.), and new membranes are systematically designed to improve these parameters. Numerous studies aimed at improving PIM technology may contribute to the wider use of these methods in the future on an industrial scale, e.g., in wastewater treatment. This review describes the latest achievements related to the removal of various metal ions by PIMs over the past 3 years, with particular emphasis on solutions with potential industrial application.