Structures, Properties, and Performances-Relationships of Polymeric Membranes for Pervaporative Desalination

Radiation‐Induced Admicellar Graft Polymerization of 2‐Hydroxyethyl Methacrylate onto Polyvinylidene Fluoride Membranes Using an Electron Beam Accelerator

The efficiency of admicellar graft polymerization in functionalizing polyvinylidene fluoride (PVDF) membranes was explored. The effect of 2‐hydroxyethyl methacrylate (HEMA) concentration and the absorbed dose was investigated using a simultaneous method of radiation‐induced graft polymerization. The degree of grafting increased with raising the absorbed dose and HEMA concentration. The Fourier transform infrared (FTIR) peak for C–O stretch and the asymmetric and symmetric stretching of the C–O–C bridge, respectively, proved the presence of poly(2‐hydroxyethyl methacrylate) (PHEMA) on the modified PVDF. As the grafting yield increased, rougher surfaces were observed. According to contact angle analysis, the grafted membrane with a higher grafting yield outperformed the low grafting yield membrane in terms of water flux and hydrophilicity.

New Membrane-Forming Aromatic Co-Poly(amide-imide)s: Influence of the Chemical Structure on the Morphological, Thermal and Transport Properties

Polymer film membranes are used to solve specific separation problems that dictate structural requirements. Structural and morphological parameters of film membranes based on glassy polyheteroarylenes can be controlled in the process of preparation from solutions that opens up prospects for obtaining structured membranes required for targeted separation. In the case of aromatic poly(amide-imide)s, the possibility of controlling film formation and structure virtually has not been studied. In the present work, a series of homologous co-poly(amide-imide)s differing in the number of repeating units with carboxyl-substituted aromatic fragments was synthesized by polycondensation. Comparative analysis of the processes of formation of membranes with different morphologies based on these polymers under equal conditions was performed. New information was obtained about the influence of the amounts of carboxyl groups and the residual solvent on structural properties of asymmetric membranes. The influence of these factors on transport properties of dense membranes under pervaporation conditions was studied. It was demonstrated that in the case of carboxyl-containing poly(amide-imide)s, the domains formed during film preparation had a significant effect on membrane properties.

Seawater Desalination by Modified Membrane Distillation: Effect of Hydrophilic Surface Modifying Macromolecules Addition into PVDF Hollow Fiber Membrane

Hollow fiber membranes of polyvinylidene fluoride (PVDF) were prepared by incorporating varying concentrations of hydrophilic surface-modifying macromolecules (LSMM) and a constant amount of polyethylene glycol (PEG) additives. The membranes were fabricated by the dry-wet spinning technique. The prepared hollow fiber membranes were dip-coated by hydrophobic surface-modifying macromolecules (BSMM) as the final step fabrication. The additives combination is aimed to produce hollow fiber membranes with high flux permeation and high salt rejection in the matter of seawater desalination application. This study prepares hollow fiber membranes from the formulation of 18 wt. % of PVDF mixed with 5 wt. % of PEG and 3, 4, and 5 wt. % of LSMM. The membranes are then dip-coated with 1 wt. % of BSMM. The effect of LSMM loading on hydrophobicity, morphology, average pore size, surface porosity, and membrane performance is investigated. Coating modification on LSMM membranes showed an increase in contact angle up to 57% of pure, unmodified PVDF/PEG membranes, which made the fabricated membranes at least passable when hydrophobicity was considered as one main characteristic. Furthermore, The PVDF/PEG/4LSMM-BSMM membrane exhibits 161 °C of melting point as characterized by the DSC. This value indicates an improvement of thermal behavior shows so as the fabricated membranes are desirable for membrane distillation operation conditions range. Based on the results, it can be concluded that PVDF/PEG membranes with the use of LSMM and BSMM combination could enhance the permeate flux up to 81.32 kg·m-2·h-1 at the maximum, with stable salt rejection around 99.9%, and these are found to be potential for seawater desalination application.

Scale-up one-pot synthesis of waste collagen and apple pomace pectin incorporated pentapolymer biocomposites: Roles of waste collagen for elevations of properties and unary/ ternary removals of Ti(IV), As(V), and V(V)

Herein, hazardous solid particulate waste collagenic fibers (SWCFs) of leather industries were incorporated into apple pomace pectin (APPN)-grafted-pentapolymer, i.e., APPN-g-[sodium 2-methylidenebutanedioate(SMBD)-co-N-((3-(isopropylamino)-3-oxopropoxy) methyl) butyramide (CM1)-co-N-(hydroxymethyl)prop-2-enamide (NHMPE)-co-N-(hydroxymethyl)-4-(N-isopropylbutyramido)butanamide (CM2)-co-N-(propan-2-yl)prop-2-enamide NPYPE)/ PENP1], i.e., APPN-g-PENP1/ PENP2, prepared via one-pot facile polymerization of APPN and synthetic monomers, i.e., SMBD, NHMPE, and NPYPE, in aqueous medium, to fabricate an optimum multifunctional hybrid biocomposite adsorbent/ HCOM3. In PENP1, PENP2, and HCOM3, fourth/ CM1 and fifth/ CM2 multifunctional comonomers were anchored in situ. The structures of PENP1, PENP2, HCOM3, CM1, CM2, and metal-ion adsorbed HCOM3; APPN-grafting; SWCF incorporation; and surface properties were analyzed through NMR, XPS, FTIR, XRD, and SEM. The elevated adsorption efficiencies (AEs), reusability, thermostability, swelling, network durability, and crosslink density of HCOM3 were attributed to variable functionalities of SWCF/ APPN, explored by DLS and TGA, swelling, network, and thermodynamic parameters. Compared to SWCF, APPN, PENP1, and PENP2, the elevated AEs and reusability compelled HCOM3 as more suitable for scalable waste management. The maximum AEs, i.e., 171.79, 180.47, and 177.27 mg g^-1, for Ti(IV), As(V), and V(V) at pH_op = 7.0, 3.0, and 5.0, respectively, within 5-100 mg L^-1 and at 298 K for 25 mg HCOM3 deteriorated during ternary adsorption by the antagonistic effects.

Thermochemical Conversion of Waste Glass and Mollusk Shells into an Absorbent Material for Separation of Direct Blue 15 Azo Dye from Industrial Wastewater

The objective of the presented work was to convert waste glass and mollusk shells into a porous material for separation of the direct blue 15 azo dye from industrial wastewater. The porous glass material of specific pore size and surface area was prepared through a thermochemical reaction by reacting waste glass with mollusk shells, soda, and rock salt. The optimal reaction conditions were determined by adjusting the reaction time, reaction temperature, and relative amount of the reactants. The surface morphology, elemental composition, and functional groups of the material were studied through scanning electron microscopy (SEM), X-ray florescence spectroscopy (XRF), energy-dispersive X-ray spectroscopy (EDX), and Fourier transform infrared spectroscopy (FT-IR). Barrett-Joyner-Halenda (BJH) and Brunauer-Emmett-Teller (BET) methods were used to determine the pore size distribution and surface area of the porous material. The material consisted of different types of flakes, oval-shaped particles, and granules. In addition to the functionalized char, the porous material contained Si-O-Si, Si-O-Al, and Si-OH groups. Relatively better yield and pore size distribution were obtained at a reaction temperature of 800 °C and reaction time of 90 min. The fully characterized material was used to separate the blue dye from industrial wastewater. This porous material absorbed about 2.66 mg/g blue dye from wastewater after 20 min of treatment time. The adsorption data fit the Freundlich isotherm better than the Langmuir isotherm. The correlation coefficient of Freundlich isotherm varied from 0.93 to 0.98, which was slightly higher than the correlation coefficient of Langmuir isotherm.

Light-Emitting Multifunctional Maleic Acid-co-2-(N-(hydroxymethyl)acrylamido)succinic Acid-co-N-(hydroxymethyl)acrylamide for Fe(III) Sensing, Removal, and Cell Imaging

The intrinsically fluorescent highly hydrophilic multifunctional aliphatic terpolymer, maleic acid (MA)-co-2-(N-(hydroxymethyl)acrylamido)succinic acid (NHASA)-co-N-(hydroxymethyl)acrylamide (NHMA), that is, 1, was designed and synthesized via C-C/N-C-coupled in situ allocation of a fluorophore monomer, that is, NHASA, composed of amido and carboxylic acid functionalities in the polymerization of two nonemissive MA and NHMA. The scalable and reusable intrinsically fluorescent biocompatible 1 was suitable for sensing and high-performance adsorptive exclusion of Fe(III), along with the imaging of Madin-Darby canine kidney cells. The structure of 1, in situ fluorophore monomer, aggregation-induced enhanced emission, cell-imaging ability, and superadsorption mechanism were studied via microstructural analyses using 1H/13C NMR, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, atomic absorption spectroscopy, ultraviolet-visible spectroscopy, thermogravimetric analysis, dynamic light scattering, high-resolution transmission electron microscopy, solid-state fluorescence, fluorescence lifetime, and fluorescence imaging, along with measuring kinetics, isotherms, and thermodynamic parameters. The location, electronic structures, and geometries of the fluorophore and absorption and emission properties of 1 were investigated using density functional theory and natural transition orbital analyses. The limit of detection and the maximum adsorption capacity were 2.45 × 10-7 M and 542.81 mg g-1, respectively.

Preparation of Elastic and Antibacterial Chitosan-Citric Membranes with High Oxygen Barrier Ability by in Situ Cross-Linking

Chitosan-citric biomembranes Ch-CA-Gx (x = 0-3) were prepared by a simple cross-linking. The dependence of mechanical property, water-resisting capacity, microstructural characteristic, oxygen barrier ability, and thermal properties of membranes on the content of glycerin was investigated. The results revealed that vacuum drying at 80 °C can lead to low-yield amidation and the Maillard reaction, thus affecting the thermal stability and water resistance of biomembranes. Owing to the ionic cross-linking and amidation, the chitosan-citrate complex showed weaker compatibility when the glycerin content increased, thereby leading to discontinuity of microstructure in the Ch-CA-Gx (x = 1-3) membranes, which was in line with the weaker mechanical properties and water-resisting abilities of membranes, compared to Ch-CA-G0. Chitosan membranes showed interestingly high oxygen barrier capabilities under 40 and 80% relative humidity (RH) conditions, probably attributed to the increased diffusion length arising from the hydrogen-bonding, ionic, and covalent cross-linking. The oxygen transmission rates of Ch-CA-Gx were below 0.1 cm3 m-2 day-1 at 40% RH. The Ch-CA-Gx membranes showed a good elasticity assigned to the reversibly cross-linked structure. The membranes presented strong antibacterial activities against Staphylococcus aureus and Escherichia coli bacteria, probably owing to the citric acids. The results demonstrated that these materials have potential applications as membranes or protecting coatings for food packaging and successful cross-linking by means of amidation, and the Maillard reaction under the condition of vacuum drying can be probably applied as a green and alternative method for the fabrication of mechanically tough and antibacterial membranes, fibers, and gels.

Chitosan-grafted tetrapolymer using two monomers: pH-responsive high-performance removals of Cu(II), Cd(II), Pb(II), dichromate, and biphosphate and analyses of adsorbed microstructures

For circumventing the cumbersome and expensive multifunctional and multipolymer adsorbents for high-performance removals of hazardous water-contaminant(s), chitosan-g-[2-acrylamido-2-methyl-1-propanoic acid (AMPS)-co-2-(3-acrylamidopropanamido)-2-methylpropane-1-sulfonic acid (APAMPS)-co-2-(N-(3-amino-3-oxopropyl)acrylamido)-2-methylpropane-1-sulfonic acid (NAOPAMPS)-co-acrylamide (AM)] (i.e., chitosan-g-tetrapolymer), a multifunctional scalable and reusable hydrogel, was synthesized by grafting of chitosan and in situ attachments of N-H functionalized NAOPAMPS and APAMPS hydrophilic acrylamido-monomers during free-radical solution-polymerization of the two ex situ added AMPS and AM monomers in water. The response surface methodology was employed to synthesize one hydrogel envisaging the optimum balance between swelling and stability for the superadsorption of Cu(II), Cd(II), Pb(II), Cr₂O₇^2-, and HPO₄^2-. The in situ attachments of NAOPAMPS and APAMPS, grafting of chitosan into tetrapolymer, structures and properties, pH-responsive abilities, superadsorption mechanism, and reusability were understood via in depth microstructural analyses of adsorbed and/or unadsorbed chitosan-g-tetrapolymer(s) through ¹H/¹³C NMR, FTIR, XPS, TGA, XRD, DLS, and pH_PZC. The maximum adsorption capacities of Cd(II), Cu(II), Pb(II), Cr₂O₇^2-, and HPO₄^2- were 1374.41, 1521.08, 1554.08, 47.76, and 32.76 mg g^-1, respectively.