Development of PVDF Ultrafiltration Membrane with Zwitterionic Block Copolymer Micelles as a Selective Layer

Study on Treatment of Tiny Pollution Water with PAC-HUM System in Kuitun River

Kuitun city, Xinjiang is dry and short of water, so it is urgent to treat and utilize all kinds of unconventional water. In view of this problem, we conducted a study on the treatment of tiny pollution water in Kuitun River. We investigated the effect of dosage of powder activated carbon (PAC) on hollow-fiber ultrafiltration membrane (HUM) performance. The results show that the stable operation time of hollow fiber ultrafiltration membranes lengthened and the rate of reduction of the flux was reduced when the PAC dosage was increased. The addition of PAC had no obvious effect on the resistance of membrane filtration. We conducted experiments to evaluate the effect of ultrafiltration of tiny pollution water in combination with PAC. When the parameters of operation and PAC dosage were appropriately regulated, the removal rates of chemical oxygen demand (COD), ammonia nitrogen (NH₃-N) and ferric ions (Fe) reached 62%, 32% and 90%, respectively. When the PAC dosage was 200 mg/L, 100 mg/L and 150 mg/L, the highest removal rates were achieved under normal temperature and pressure. The effluent COD was less than 5.0 mg/L, NH₃-N was less than 1.5 mg/L and Fe was less than 0.5 mg/L, achieving better results than the quality standard of surface water (GB3838-2002). The treated water can be discharged into the river or recirculated to utilities. The fouled membrane was cleaned by water rinsing, water/acid rinsing and water/alkali rinsing, with recovery ratios of 44%, 81% and 88%, respectively. The results of this study can serve as a foundation for the efficient utilization of water resources and the development of new water treatment technologies in Xinjiang.

Nano-Fibrous Networks from Co-Assembly of Amphiphilic Peptide and Polyelectrolyte

Organize the matter on an increasingly small scale is sought in order to increase the performance of materials. In the case of porous materials, such as filtration membranes, a compromise must be found between the selectivity provided by this nanostructuring and a permeability in particular linked to the existing pore volume. In this work, we propose an innovative waterborne approach consisting in co-assembling peptide amphiphiles (PA) which will provide nanostructuring and polyelectrolytes which will provide them with sufficient mechanical properties to sustain water pressure. C₁₆-V₃A₃K₃G-NH₂ PA nanocylinders were synthesized and co-assembled with poly(sodium 4-styrenesulfonate) (PSSNa) into porous nano-fibrous network via electrostatic interactions. The ratio between C₁₆-V₃A₃K₃G-NH₂ and PSSNa was studied to optimize the material structure. Since spontaneous gelation between the two precursors does not allow the material to be shaped, various production methods have been studied, in particular via tape casting and spray-coating. Whereas self-supported membranes were mechanically weak, co-assemblies supported onto commercial ultrafiltration membranes could sustain water pressure up to 3 bars while a moderate permeability was measured confirming the existence of a percolated network. The produced membrane material falls into the ultrafiltration range with a pore radius of about 7.6 nm.

Preparation of an Ultrafiltration (UF) Membrane with Narrow and Uniform Pore Size Distribution via Etching of SiO2 Nano-Particles in a Membrane Matrix

The UF membrane with a narrow and uniform pore size distribution and a low tendency to foul has significant applications in wastewater treatment. A major hindrance in the preparation of the UF membrane with these features is the lack of a scalable and economical membrane fabrication method. Herein, we devise a new strategy to prepare a high-quality polyvinylidene fluoride/polymethyl acrylate/cellulose acetate (PVDF/PMMA/CA) blend UF membrane via a combination of the etching mechanism with the traditional Loeb–Sourirajan (L-S) phase inversion method. Different concentrations of silicon dioxide (SiO₂) nanoparticles (NP) in the membrane matrix were etched by using a 0.2 M hydrofluoric acid (HF) solution in a coagulation bath. This strategy provided the membrane with unique features along with a narrow and uniform pore size distribution (0.030 ± 0.005 μm). The etched membrane exhibits an increase of 2.3 times in pure water flux (PWF) and of 6.5 times in permeate flux(PF), with a slight decrease in rejection ratio (93.2% vs. 97%) when compared to than that of the un-etched membrane. Moreover, this membrane displayed outstanding antifouling ability, i.e., a flux recovery ratio (FRR) of 97% for 1000 mg/L bovine serum albumin (BSA) solution, a low irreversible fouling ratio of 0.5%, and highly enhanced hydrophilicity due to the formation of pores/voids throughout the membrane structure. The aforementioned features of the etched membrane indicate that the proposed method of etching SiO₂ NP in membrane matrix has a great potential to improve the structure and separation efficiency of a PVDF/PMMA/CA blend membrane.