Numerical Analysis of RTD Curves and Inclusions Removal in a Multi-Strand Asymmetric Tundish with Different Configuration of Impact Pad

Effect of Uniform and Non-Uniform Increasing Casting Flow Rate on Dispersion and Outflow Percentage of Tracers in Four Strand Tundishes under Strand Blockage Conditions

The flow field, tracer dispersion and uniformity of strands in two designs of four-strand tun-dishes under normal conditions and single-strand blockage conditions are studied by numerical simulation. The casting speed (flow rate) of strands are increasing uniformly or non-uniformly to improve the strand blockage condition. The uniformity of strands of the cases are evaluated by a novel outflow percentage analysis method. The results show that the flow field in the tundish does not change significantly when the single-strand is blocked or the casting flow rate is increased. After blockage of one strand, the consistency of each strand of u-shaped weir tundish is better than that of double-weir tundish. With the uniform increasing of the casting flow rate, the response time of each strand decreases and the outflow percentage increases. However, the uniformity of strands improved slightly in double-weir tundish but decreased in u-shaped tundish. For the double-weir tundish, significantly increasing the casting flow rate of the strand located in the blocked part by a factor of 1.5 and slightly increasing the casting flow rate of the other strands by a factor of 1.25, the consistency of each strand is the best. For the u-shaped weir tundish, the consistency of each strand is improved by non-uniform increasing of the casting flow rate of the strands. The flow rate of the strand located in the blocked part and the other strands is increased by a factor of 1.25, and 1.375 or 1.2 and 1.4 are the optimized cases.

A Simulation-Based Digital Design Methodology for Studying Conjugate Heat Transfer in Tundish

The successful design of refractory lining for a tundish is critical due to the demand of superheat control, improvement of steel cleanliness and reduction in material cost during continuous casting. A design of experiment analysis, namely, the Taguchi method, was employed to analyze two-dimensional heat transfer through refractory linings of a single-strand tundish, with the consideration of the thickness and the thermal conductivity of lining materials. In addition, a three-dimensional conjugate heat transfer model was applied in the tundish, taking in account the molten steel flow and heat conduction in the linings. A special focus of this study was to demonstrate the analysis methodology of combining Taguchi and CFD modelling to explore lining design in terms of thickness and thermal conductivity for the given process conditions during tundish operations.

Evolution of Chemical Composition and Modeling of Growth Nonmetallic Inclusions in Steel Containing Yttrium

The programs WYK_Stal and Bi-Growth, developed at AGH-UST, Kraków, Poland, were used for simulating the refining process, the formation of non-metallic inclusions, and their growth. The Fe-Y-Al-O-S-Ca system in pre-oxidized steel was analyzed, where yttrium formed precipitates from both O and S. When first Al and second Y were added to steel, the proportion of Al₂O₃ inclusions remained constant. This resulted in higher yttrium losses for oxide formation, whereas the sulfur content promoted sulfide phase formation. The introduction of yttrium at the end of refining contributed to reducing the consumption of this element in the non-metallic phase formation. The addition of aluminum and then calcium were sufficient to achieve a high degree of deoxidation and desulfurization. Calculations performed with WYK_Stal for both (a) and (c) versions of the model showed that the sulfide phase was constituted by CaS and FeS (model c) and CaS (model (a)). The participation of the calcium sulfide phase turned out to be dominant in the inclusions. Their presence was also identified in the slag phase. Simulations of the growth of complex oxide and oxo-sulfide inclusions using the Bi_Growth program showed that the yttrium content of the steel has a decisive role in the formation of complex oxide inclusions and the final oxygen content of the steel. In contrast, for the growth of oxide-sulfide inclusions, the character of growth is determined by the sulfur content of steel.

Synthesis of a CFD Benchmark Exercise: Examining Fluid Flow and Residence-Time Distribution in a Water Model of Tundish

Computational Fluid Dynamics (CFD) has become an indispensable tool that can potentially predict many phenomena of practical interest in the tundish. Model verification and validation (V&V) are essential parts of a CFD model development process if the models are to be used with sufficient confidence in real industrial tundish applications. The crucial aspects of CFD simulations in the tundish are addressed in this study, such as the selection of the turbulence models, meshing, boundary conditions, and selection of discretization schemes. A series of CFD benchmarking exercises are presented serving as selected examples of appropriate modelling strategies. A tundish database, initiated by German Steel Institute VDEH working group "Fluid Mechanics and Fluid Simulation", was revisited with the aim of establishing a comprehensive set of best practice guidelines (BPG) in CFD simulations for tundish applications. These CFD benchmark exercises yield important results for the sensible application of CFD models and contribute to further improving the reliability of CFD applications in metallurgical reactors.

Evolution of the Numerical Model Describing the Distribution of Non-Metallic Inclusions in the Tundish

Continuous casting is one of the steel production stages, during which the improvement in the metallurgical purity of steel can be additionally affected by removing nonmetallic inclusions (NMIs). This can be achieved by means of various types of flow controllers, installed in the working space of the tundish. The change in the steel flow structure, caused by those flow controllers, should lead to an intensification of NMIs removal from the liquid metal to the slag. Therefore, it is crucial to understand the behavior of nonmetallic inclusions during the flow of liquid steel through the tundish, and particularly during their distribution. The presented paper reports the results of the modeling studies of NMI distribution in liquid steel, flowing through the tundish. CFD modeling methods—using different models and computation variants—were employed in the study. The obtained CFD results were compared with the results of laboratory tests (using a tundish water model). The results of the performed investigations allow us to compare both methods of modeling; the investigated phenomena were microparticle distribution and mass microparticle concentration in the model fluid. The validation of the CFD results verified the analyzed computation variants. The aim of the research was to determine which numerical model is the best for describing the studied phenomenon. This will be used as the first phase of a larger research program which will provide for a comprehensive study of the distribution of NMIs flowing through tundish steel.

Application of Tanks-in-Series Model to Characterize Non-Ideal Flow Regimes in Continuous Casting Tundish

This study describes a new tanks-in-series model for analyzing non-ideal flow regimes in a single-strand tundish. The tundish was divided into two interconnected tanks, namely an inlet tank and an outlet tank. A water model experiment was carried out to separately measure the residence-time distribution (RTD) of the two tanks. Drift beads were adopted in the water model experiment to simulate the non-metallic inclusions in molten steel. Dead volume fraction was evaluated by analyzing measured RTD curves. The ratio between mixed flow volume and plug flow volume was proposed as a new criterion to evaluate the inclusion removal. In the inlet tank, a higher mixed flow fraction was preferred to effectively release turbulent kinetic energy and enhance inclusion collision growth. In the outlet tank, a higher plug flow fraction was preferred to facilitate inclusion removal by flotation. The optimal positions of the weir were recommended based on the RTD analysis and the inclusion removal from the results of water model experiments. A theoretical equation was derived based on the tanks-in-series model, providing a good fitting function to analyze the experimental data. The confirmation test was performed by applying computational fluid dynamics simulations of liquid steel flow in the real tundish.