Particle Ejection by Jetting and Related Effects in Impact Welding Processes

Analytical Estimation of Electromagnetic Pressure, Flyer Impact Velocity, and Welded Joint Length in Magnetic Pulse Welding

Magnetic pulse welding involves the joining of two metallic parts in a solid state by the use of a short and intense electromagnetic impulses and the resulting impact between the parts. The coalesced interface undergoes visco-plastic deformation at a high strain rate and exhibits a wavy shape at a microscopic scale. A practical estimation of the electromagnetic pressure, impact velocity and welded joint length as a function of the process conditions and the electromagnetic coil geometry is required but currently not available. Three novel analytical relations for the estimation of the electromagnetic pressure, impact velocity, and welded joint length for magnetic pulse welding of tubes and sheets, are presented. These relations were developed systematically, following a dimensional analysis, and validated for a wide range of conditions from independent literature. The comparison of the analytically computed results and the corresponding values reported in the literature has illustrated that the proposed analytical relations can be used for the estimation of the electromagnetic pressure and impact velocity for the magnetic pulse welding of tubes and sheets with a good level of confidence. The analytically calculated results for the welded joint length show a little discrepancy with the corresponding experimentally measured values. Further investigations and more experimentally measured results are required to arrive at a more comprehensive analytical relation for the prediction of welded joint length.

The Energy Balance in Aluminum–Copper High-Speed Collision Welding

Collision welding is a joining technology that is based on the high-speed collision and the resulting plastic deformation of at least one joining partner. The ability to form a high-strength substance-to-substance bond between joining partners of dissimilar metals allows us to design a new generation of joints. However, the occurrence of process-specific phenomena during the high-speed collision, such as a so-called jet or wave formation in the interface, complicates the prediction of bond formation and the resulting bond properties. In this paper, the collision welding of aluminum and copper was investigated at the lower limits of the process. The experiments were performed on a model test rig and observed by high-speed imaging to determine the welding window, which was compared to the ones of similar material parings from former investigation. This allowed to deepen the understanding of the decisive mechanisms at the welding window boundaries. Furthermore, an optical and a scanning electron microscope with energy dispersive X-ray analysis were used to analyze the weld interface. The results showed the important and to date neglected role of the jet and/or the cloud of particles to extract energy from the collision zone, allowing bond formation without melting and intermetallic phases.

AlMg6 to Titanium and AlMg6 to Stainless Steel Weld Interface Properties after Explosive Welding

This paper studies the weld interface microstructure and mechanical properties of AlMg6-stainless steel and AlMg6-titanium bimetals produced using explosive welding. The microhardness (HV), tear strength, and microstructure of the weld seams were evaluated. The interface of the weld zones had a flat profile. No structural disturbances or heterogeneity in the AlMg6-titanium weld interface were observed. On the other hand, the bimetal AlMg6-stainless steel had extensive zones of cast inclusions in the 10–30 µm range. SEM/energy-dispersive X-ray spectroscopy (EDS) analysis showed the presence of a hard and brittle intermetallic compound of Al and FeAl3 (with 770–800 HV). The microhardness of the AlMg6-titanium bimetal grew higher closer to the weld interface and reached 207 HV (for AlMg6) and 340 HV (for titanium). Both bimetals had average tear strength below 100 MPa. However, the tear strength of some specimens reached 186 and 154 MPa for AlMg6-titanium and AlMg6-stainless steel, respectively. It is also worth mentioning that heat treatment at 200 °C for one hour led to a uniform distribution of tear strength along the entire length of the bimetals. The study shows that one of the possible solutions to the problem of the formation of the brittle intermetallic compounds would be the use of intermediate layers of refractory metals.

Interface Formation during Collision Welding of Aluminum

Collision welding is a high-speed joining technology based on the plastic deformation of at least one of the joining partners. During the process, several phenomena like the formation of a so-called jet and a cloud of particles occur and enable bond formation. However, the interaction of these phenomena and how they are influenced by the amount of kinetic energy is still unclear. In this paper, the results of three series of experiments with two different setups to determine the influence of the process parameters on the fundamental phenomena and relevant mechanisms of bond formation are presented. The welding processes are monitored by different methods, like high-speed imaging, photonic Doppler velocimetry and light emission measurements. The weld interfaces are analyzed by ultrasonic investigations, metallographic analyses by optical and scanning electron microscopy, and characterized by tensile shear tests. The results provide detailed information on the influence of the different process parameters on the classical welding window and allow a prediction of the different bond mechanisms. They show that during a single magnetic pulse welding process aluminum both fusion-like and solid-state welding can occur. Furthermore, the findings allow predicting the formation of the weld interface with respect to location and shape as well as its mechanical strength.