Dynamically Recrystallized Microstructures, Textures, and Tensile Properties of a Hot Worked High-Mn Steel

Determining the Hot Workability and Microstructural Evolution of an Fe-Cr-Mo-Mn Steel Using 3D Processing Maps

The Laasraoui segmented and Arrhenius flow stress model, dynamic recrystallization (DRX) model, grain size prediction model, and hot processing map (HPM) of Fe-Cr-Mo-Mn steels were established through isothermal compression tests. The models and HPM were proven by experiment to be highly accurate. As the deformation temperature decreased or the strain rate increased, the flow stress increased and the grain size of the Fe-Cr-Mo-Mn steel decreased, while the volume fraction of DRX (Xdrx) decreased. The optimal range of the hot processing was determined to be 1050-1200 °C/0.369-1 s-1. Zigzag-like grain boundaries (GBs) and intergranular cracks were found in the unstable region, in which the disordered martensitic structure was observed. The orderly packet martensite was formed in the general processing region, and the mixed structure with incomplete DRX grains was composed of coarse and fine grains. The microstructure in the optimum processing region was composed of DRX grains and the multistage martensite. The validity of the Laasraoui segmented flow stress model, DRX model, grain size prediction model, and HPM was verified by upsetting tests.

Microstructural Evolution and an Improved Dynamic Recrystallization Kinetic Model of a Ni-Cr-Mo Alloy in Hot Deformation

Microstructural evolution and dynamic recrystallization (DRX) behaviors of a Ni-Cr-Mo alloy were researched utilizing hot compressive experiments. The changed features of dislocation, subgrain and grain structure correlating to forming parameters were examined by transmission electron microscope (TEM) and electron backscatter diffraction (EBSD). Results illustrate that the consumption of dislocation and the coarsening of substructure/DRX grain are prominently enhanced with an increased forming temperature. However, the annihilation/interaction of dislocation and the expansion of subgrain/DRX grain boundary can be limited at a larger strain rate. Meanwhile, considering the discrepancy in DRX variation rates concerning the strain rate’s ranges, an improved DRX kinetic model was developed. Compared to the classical DRX kinetic model, the good consistency between the forecasted and tested results demonstrates that the established improved DRX kinetic model can precisely characterize the DRX features of the Ni-Cr-Mo alloy over a wide strain rate range. Additionally, the EBSD’s quantitative statistical results proved that the variation of DRX grain size can be supremely defined as the power formulation of the forming temperature and strain rate.

High Temperature Deformation Behavior and Microstructure Evolution of Low-Density Steel Fe30Mn11Al1C Micro-Alloyed with Nb and V

The thermal processing parameters is very important to the hot rolling and forging process for producing grain refinement in lightweight high-manganese and aluminum steels. In this work, the high temperature deformation behaviors of a low-density steel of Fe30Mn11Al1C alloyed with 0.1Nb and 0.1V were studied by isothermal hot compression tests at temperatures of 850–1150 °C and strain rates between 0.01 s⁻¹ and 10 s⁻¹. It was found that the flow stress constitutive model could be effectively established by the Arrhenius based hyperbolic sine equation with an activation energy of about 389.1 kJ/mol. The thermal processing maps were developed based on the dynamic material model at different strains. It’s shown that the safe region for high temperatures in a very broad range of both deformation temperature and deformation strain and only a small unstable high deformation region, located at low temperatures lower than 950 °C. The deformation microstructures were found to be fully recrystallized microstructure in the safe deformation region and the grain size decreases along with decreasing temperature and increasing strain rate. Whereas the deformation microstructures is composed by grain refinement-recrystallized grains and a small fraction of non-recrystallized microstructure in the unstable deformation region, indicating that the deformation behaviors controlled by continuous dynamic recrystallization. The Hall Petch relationship between microhardness and the grain size of the high temperature deformed materials indicates that high strength low-density steel could be developed by a relative low temperature deformation and high strain rate.

Peculiarities of DRX in a Highly-Alloyed Austenitic Stainless Steel

The features of discontinuous dynamic recrystallization (DRX) in a highly-alloyed austenitic stainless steel were studied at temperatures of 800 °C to 1100 °C. Hot deformation accompanied by DRX was characterized by an activation energy of 415 kJ/mol. The frequency of the sequential DRX cycles depended on the deformation conditions; and the largest fraction of DRX grains with small grain orientation spread below 1° was observed at a temperature of around 1000 °C and a strain rate of about 10⁻³ s⁻¹. The following power law relationships were obtained for DRX grain size (D_DRX) and dislocation density (ρ) vs. temperature-compensated strain rate (Z) or peak flow stress (σ_P): D_DRX ~ Z^−0.25, ρ ~ Z^0.1, σ_P ~ D_DRX^−0.9, σ_P ~ ρ^1.4. The latter, i.e., σ_P ~ ρ^1.4, was valid in the flow stress range below 300 MPa and changed to σ_P ~ ρ^0.5 on increasing the stress. The obtained dependencies suggest a unique power law function between the dislocation density and the DRX grain size with an exponent of −0.5.

A Flow Stress Model of 300M Steel for Isothermal Tension

To investigate the effect of hot working parameters on the flow behavior of 300M steel under tension, hot uniaxial tensile tests were implemented under different temperatures (950 °C, 1000 °C, 1050 °C, 1100 °C, 1150 °C) and strain rates (0.01 s⁻¹, 0.1 s⁻¹, 1 s⁻¹, 10 s⁻¹). Compared with uniaxial compression, the tensile flow stress was 29.1% higher because dynamic recrystallization softening was less sufficient in the tensile stress state. The ultimate elongation of 300M steel increased with the decrease of temperature and the increase of strain rate. To eliminate the influence of sample necking on stress-strain relationship, both the stress and the strain were calibrated using the cross-sectional area of the neck zone. A constitutive model for tensile deformation was established based on the modified Arrhenius model, in which the model parameters (n, α, Q, ln(A)) were described as a function of strain. The average deviation was 6.81 MPa (6.23%), showing good accuracy of the constitutive model.

The Influence of Warm Rolling on Microstructure and Deformation Behavior of High Manganese Steels

In this work, a Fe23Mn0.3C1Al high manganese twinning-induced plasticity (TWIP) steel is subjected to varying warm rolling procedures in order to increase the yield strength and maintain a notable ductility. A comprehensive material characterization allows for the understanding of the activated deformation mechanisms and their impact on the resulting microstructure, texture, and mechanical properties. The results show a significant enhancement of the yield strength compared to a fully recrystallized Fe23Mn0.3C1Al steel. This behavior is mainly dominated by the change of the active deformation mechanisms during rolling. Deformation twinning is very pronounced at lower temperatures, whereas this mechanism is suppressed at 500 °C and a thickness reduction of up to 50%. The mechanical properties can be tailored by adjusting rolling temperature and thickness reduction to desired applications.