Occupational Exposure to Fine Particles and Ultrafine Particles in a Steelmaking Foundry

A pilot study of occupational exposure to ultrafine particles during 3D printing in research laboratories

Introduction

3D printing is increasingly present in research environments, and could pose health risks to users due to air pollution and particulate emissions. We evaluated the nanoparticulate emissions of two different 3D printers, utilizing either fused filament fabrication with polylactic acid, or stereolithography (SLA) with light curing resin.

Methods

Nanoparticulate emissions were evaluated in two different research environments, both by environmental measurements in the laboratory and by personal sampling.

Results

The SLA printer had higher nanoparticulate emissions, with an average concentration of 4,091 parts/cm³, versus 2,203 particles/cm³ for the fused filament fabrication printer. The collected particulate matter had variable morphology and elemental composition with a preponderance of carbon, sulfur and oxygen, the main byproducts.

Discussion

Our study implies that when considering the health risks of particulate emissions from 3D printing in research laboratories, attention should be given to the materials used and the type of 3D printer.

Assessment of coarse, fine, and ultrafine particulate matter at different microenvironments of fire stations

The concentrations of respirable particulate matter (PM) and the impact on indoor air quality in occupational settings remains poorly characterized. This study assesses, for the first time, the cumulative and non-cumulative concentrations of 14 fractions of coarse (3.65-9.88 μm), fine (0.156-2.47 μm), and ultrafine (0.015-0.095 μm) PM inside the garage of heavy vehicles, firefighting personal protective equipment' storage room, bar, and a common area of seven Portuguese fire stations. Sampling campaigns were performed during a regular work week at the fire stations. Levels of daily total cumulative PM ranged from 277.4 to 413.2 μg/m³ (maximum values of 811.4 μg/m³), with the bar (370.1 μg/m³) and the PPE' storage room (361.3 μg/m³) presenting slightly increased levels (p > 0.05) than the common area (324.8 μg/m³) and the garage (339.4 μg/m³). The location of the sampling site, the proximity to local industries and commercial activities, the layout of the building, the heating system used, and indoor sources influenced the PM concentrations. Fine (193.8-301.0 μg/m³) and ultrafine (41.3-78.2 μg/m³) particles were predominant in the microenvironments of all fire stations and accounted for 71.5% and 17.8% of daily total cumulative levels, respectively; coarse particles (23.3-47.1 μg/m³) represented 10.7% of total PM. The permissible exposure limit (5.0 mg/m³) defined by the Occupational Safety and Health Organization for respirable dust was not overcome in the evaluated fire stations. Results suggest firefighters' regular exposure to fine and ultrafine PM inside fire stations which will contribute to cardiorespiratory health burden. Further studies are needed to characterize firefighters' exposure to fine and ultrafine PM inside fire stations, identify main emission sources, and evaluate the contribution of exposures at fire stations to firefighters' occupational health risks.

Relationship between Indoor High Frequency Size Distribution of Ultrafine Particles and Their Metrics in a University Site

Exposure to ultrafine particles (UFPs size < 100 nm) in life and work environments can contribute to adverse health effects also in terms of health burden of related diseases over time. The choice of parameters which better characterize UFPs is challenging, due to their physical-chemical properties and their variable size. It is also strictly related to the availability of different instrumental techniques. In the present study we focus on real time high frequency (1 Hz) UFPs particle size distribution (PSD) and their relationship with total particle number concentration (TPNC) and mean particle diameter (Davg) as a contribution characterizing by size the human exposure to UFPs in an indoor site of the University of Rome “Sapienza” (Italy). Further considerations about UFPs contribution to nucleation mode (NM) and accumulation mode (AM) have been highlighted, also in order to investigate the contribution of polycyclic aromatic hydrocarbons (PAHs) surface-adsorbed on indoor air particles (pPAHs). High indoor TPNC values were registered during the rush hours (early morning and mid/late afternoon) according to the outdoor influences originated from anthropogenic activities. AM mainly contribute to the indoor TPNC during working days showing high correlation with pPAHs. These findings may provide useful indications in terms of occupational exposure to UFPs since there are many evidences that indoor exposures to such pollutants may be associated with adverse health effects also in working environments.

Ironmaking and Steelmaking

Steel is a critical material in our society and will remain an important one for a long time into the future [...]

Occupational Fine/Ultrafine Particles and Noise Exposure in Aircraft Personnel Operating in Airport Taxiway

The occupational exposure to airborne fine and ultrafine particles (UFPs) and noise in aircraft personnel employed in airport taxiway was investigated. Stationary samplings and multiple personal sampling sites and job tasks were considered. Size distribution, particle number concentrations, lung dose surface area were measured by personal particle counters and by means of an electric low pressure impactor (ELPI+TM). Morphological and chemical characterization of UFPs were performed by transmission and scanning electron microscopy, the latter together with energy dispersive X-Ray spectroscopy based spatially resolved compositional mapping. A-weighted noise exposure level A-weighted noise exposure level normalized to an 8 h working day and Peak Sound C-weighted Pressure Level was calculated for single worker and for homogeneous exposure groups. Our study provides evidence on the impact of aviation-related emissions on occupational exposure to ultrafine particles and noise exposure of workers operating in an airport taxiway. Main exposure peaks are related to pre-flight operations of engine aircrafts. Although exposure to ultrafine particles and noise appears to not be critical if compared with other occupational scenarios, the coincidence in time of high peaks of exposure to ultrafine particles and noise suggest that further investigations are warranted in order to assess possible subclinical and clinical adverse health effects in exposed workers, especially for cardiovascular apparatus.