Wetting Properties of Transparent Anatase/Rutile Mixed Phase Glancing Angle Magnetron Sputtered Nano-TiO2 Films

Surface-Mediated Modulation of Different Biological Responses on Anatase-Coated Titanium

Various surface modification strategies are being developed to endow dental titanium implant surfaces with micro- and nano-structures to improve their biocompatibility, and first of all their osseointegration. These modifications have the potential to address clinical concerns by stimulating different biological processes. This study aims to evaluate the biological responses of ananatase-modified blasted/etched titanium (SLA-anatase) surfaces compared to blasted/acid etched (SLA) and machined titanium surfaces. Using unipolar pulsed direct current (DC) sputtering, a nanocrystalline anatase layer was fabricated. In vitro experiments have shown that SLA-anatase discs can effectively promote osteoblast adhesion and proliferation, which are regarded as important features of a successful dental implant with bone contact. Furthermore, anatase surface modification has been shown to partially enhance osteoblast mineralization in vitro, while not significantly affecting bacterial colonization. Consequently, the recently created anatase coating holds significant potential as a promising candidate for future advancements in dental implant surface modification for improving the initial stages of osseointegration.

Impact of Hydrophobic and Electrostatic Forces on the Adsorption of Acacia Gum on Oxide Surfaces Revealed by QCM-D

The adsorption of Acacia gum from two plant exudates, A. senegal and A. seyal, at the solid-liquid interface on oxide surfaces was studied using a quartz crystal microbalance with dissipation monitoring (QCM-D). The impact of the hydrophobic and electrostatic forces on the adsorption capacity was investigated by different surface, hydrophobicity, and charge properties, and by varying the ionic strength or the pH. The results highlight that hydrophobic forces have higher impacts than electrostatic forces on the Acacia gum adsorption on the oxide surface. The Acacia gum adsorption capacity is higher on hydrophobic surfaces compared to hydrophilic ones and presents a higher stability with negatively charged surfaces. The structural configuration and charge of Acacia gum in the first part of the adsorption process are important parameters. Acacia gum displays an extraordinary ability to adapt to surface properties through rearrangements, conformational changes, and/or dehydration processes in order to reach the steadiest state on the solid surface. Rheological analysis from QCM-D data shows that the A. senegal layers present a viscous behavior on the hydrophilic surface and a viscoelastic behavior on more hydrophobic ones. On the contrary, A. seyal layers show elastic behavior on all surfaces according to the Voigt model or a viscous behavior on the hydrophobic surface when considering the power-law model.

Filter Modified with Hydrophilic and Oleophobic Coating for Efficient and Affordable Oil/Water Separation

To mitigate the damage of oil spills, a filter modified with a hydrophilic and oleophobic coating is proposed for affordable and efficient oil separation and recovery from water. The sol–gel method was chosen to produce a colloidal suspension of titanium dioxide particles for its ease of production and its versatility in application for many different substrates, including paper and cloth fabric. After immersing the substrates into a titanium-containing solution, three techniques were applied to increase the production of titanium dioxide—microwave-assisted, refrigeration, and ultra-sonication. Contact angle tests were done to investigate the change in the filter’s oleophobicity. The titanium dioxide present on the surface of the filter was amorphous, but all treatment methods showed an improvement in oleophobicity. All treated filters improved oil filtration performance by up to eighty percent. The filters isolated motor oil from a mixture while allowing water to pass through. The coated filters also displayed photocatalytic activity by degrading methylene blue on its surface when exposed to sunlight, demonstrating the filter’s self-cleaning ability. For real-world applications, the filter can be supported by a stainless mesh for enhanced strength and durability. While being dragged through the water, the filter collects the surface oil, allowing water to pass through via gravity.

The Sensitization of TiO2 Thin Film by Ag Nanoparticles for the Improvement of Photocatalytic Efficiency

The formation of Ag nanoparticles on the surface of TiO2 (AgNP/TiO2) to enhance photocatalytic efficiency was studied. The Ag nanoparticles (AgNP) size, form, and distribution dependence on the initial thickness of Ag thin films, annealing temperature, and time were analyzed. The optimal annealing temperature of 400 °C and annealing time of 60 min were chosen to form AgNP from the initial Ag thin films with a thickness of 5, 7.5, and 10 nm. The formation of AgNP was done on amorphous TiO2 (a-TiO2), which crystallized into the anatase phase after the annealing. The photocatalytic efficiency (k–degradation rate constant, Defi–degradation efficiency) was evaluated by the photodegradation of Rhodamine B aqueous solution. The results suggested that the highest photocatalytic efficiency of Rhodamine B aqueous solution was reached where the average diameter (DA) of AgNP was ~38 nm (k38 = 0.017 min−1, Defi_38 = 63.5%), compared to 27 and 82 nm (k27 = 0.012 min−1, Defi_27 = 51.2% and k82 = 0.011 min−1, Defi_82 = 52.1%, respectively). The acquired results did not show clear correlation between the size and distribution of the AgNP on the TiO2 surface and photocatalytic efficiency. Nevertheless, the results suggest that AgNP can enhance the photocatalytic efficiency of TiO2 thin films (kTiO2 = 0.008 min−1, Defi_TiO2 = 36.3%).

Surface Wettability and Electrical Resistance Analysis of Droplets on Indium-Tin-Oxide Glass Fabricated Using an Ultraviolet Laser System

Indium tin oxide (ITO) is widely used as a substrate for fabricating chips because of its optical transparency, favorable chemical stability, and high electrical conductivity. However, the wettability of ITO surface is neutral (the contact angle was approximately 90°) or hydrophilic. For reagent transporting and manipulation in biochip application, the surface wettability of ITO-based chips was modified to the hydrophobic or nearly hydrophobic surface to enable their use with droplets. Due to the above demand, this study used a 355-nm ultraviolet laser to fabricate a comb microstructure on ITO glass to modify the surface wettability characteristics. All of the fabrication patterns with various line width and pitch, depth, and surface roughness were employed. Subsequently, the contact angle (CA) of droplets on the ITO glass was analyzed to examine wettability and electrical performance by using the different voltages applied to the electrode. The proposed approach can succeed in the fabrication of a biochip with suitable comb-microstructure by using the optimal operating voltage and time functions for the catch droplets on ITO glass for precision medicine application. The experiment results indicated that the CA of droplets under a volume of 20 μL on flat ITO substrate was approximately 92° ± 2°; furthermore, due to its lowest surface roughness, the pattern line width and pitch of 110 μm exhibited a smaller CA variation and more favorable spherical droplet morphology, with a side and front view CA of 83° ± 1° and 78.5° ± 2.5°, respectively, while a laser scanning speed of 750 mm/s was employed. Other line width and pitch, as well as scanning speed parameters, increased the surface roughness and resulted in the surface becoming hydrophilic. In addition, to prevent droplet morphology collapse, the droplet’s electric operation voltage and driving time did not exceed 5 V and 20 s, respectively. With this method, the surface modification process can be employed to control the droplet’s CA by adjusting the line width and pitch and the laser scanning speed, especially in the neutral or nearly hydrophobic surface for droplet transporting. This enables the production of a microfluidic chip with a surface that is both light transmittance and has favorable electrical conductivity. In addition, the shape of the microfluidic chip can be directly designed and fabricated using a laser direct writing system on ITO glass, obviating the use of a mask and complicated production processes in biosensing and biomanipulation applications.