Application of Conducting Polymer Nanostructures to Electrochemical Biosensors

Photoinduced modulation and the effect of CNT loading on field effect transistor characteristics of CNT/ZnO/PVDF composite

Carbon nanotube (CNT)/ZnO/ polyvinylidene fluoride (PVDF) polymer composite phototransistor is studied for the effect of CNT loading and the photoinduced modulation on its transfer characteristics. XRD study shows that the induced strain in the composite is due to the addition of CNT to the ZnO/PVDF composite. The percentage ofβ-phase present in PVDF is estimated through Raman spectroscopy and the composite's spectral response is determined by UV-Vis absorbance spectroscopy. From the DC electrical conductivity study it is found that the percolation threshold for the composites is obtained for 0.3 wt% of CNT, and 0.44 wt % of CNT loading makes the composite conductive. On adding 1 wt% of CNT, the electrical conductivity of the ZnO/PVDF composite increases 40 times (∼0.2μS m-1). The temperature-dependent DC conductivity shows that the conductivity of the composites changes from variable range hopping to band conductance upon an increase in CNT loading above the percolation threshold and exhibits a negative temperature coefficient. Two terminal photoconductivity studies are done to understand the photo enhancement and sensitivity of all the devices. PE hysteresis studies show that the polarization of the composites increases drastically from 0.05μC cm-2below the percolation threshold to 10-30μC cm-2above the percolation threshold of CNT in the composite. To study the effect of interfacial polarization on photoconductivity, the composite is studied in a three-terminal device format using SiO2as a gate dielectric. A band diagram analysis of the oxide-composite and CNT/ZnO interface is done to understand the mechanism behind the photoinduced field effect on transfer characteristics and the effect of CNT loading. The switching behavior and decay time under UV illumination are studied to understand the effect of CNT loading and photoinduced polarization. The persistent photoconductivity decreases and the charge collection efficiency of the FET increases as the CNT loading increases.

State-of-the-art nanosensors and kits for the detection of antibiotic residues in milk and dairy products

Antibiotic resistance is increasingly seen as a future concern, but antibiotics are still commonly used in animals, leading to their accumulation in humans through the food chain and posing health risks. The development of nanomaterials has opened up possibilities for creating new sensing strategies to detect antibiotic residues, resulting in the emergence of innovative nanobiosensors with different benefits like rapidity, simplicity, accuracy, sensitivity, specificity, and precision. Therefore, this comprehensive review provides pertinent and current insights into nanomaterials-based electrochemical/optical sensors for the detection of antibitic residues (ANBr) across milk and dairy products. Here, we first discuss the commonly used ANBs in real products, the significance of ANBr, and also their binding/biological properties. Then, we provide an overview of the role of using different nanomaterials on the development of advanced nanobiosensors like fluorescence-based, colorimetric, surface-enhanced Raman scattering, surface plasmon resonance, and several important electrochemical nanobiosensors relying on different kinds of electrodes. The enhancement of ANB electrochemical behavior for detection is also outlined, along with a concise overview of the utilization of (bio)recognition units. Ultimately, this paper offers a perspective on the future concepts of this research field and commercialized nanomaterial-based sensors to help upgrade the sensing techniques for ANBr in dairy products.

An insight into the state of nanotechnology-based electrochemical biosensors for PCOS detection

Polycystic ovary syndrome (PCOS) is one of the most common endocrine disorders affecting many women of reproductive age all over the world. PCOS is associated with the onset of enduring health complications, notably diabetes and cardiovascular diseases. Furthermore, PCOS escalates the propensity for conditions such as obesity, insulin resistance, and dyslipidemia, which can potentially culminate in life-threatening scenarios. A pervasive predicament surrounding PCOS pertains to its underdiagnosis due to discrepancies in diagnostic criteria and the intricacy of available testing methodologies. Consequently, many women encounter substantial delays in diagnosis with traditional diagnostic approaches. Prompt identification is imperative, as any delay can precipitate severe consequences. The conventional techniques employed for PCOS detection typically suffer from suboptimal accuracy, protracted assay times, and inherent limitations, thereby constraining their widespread applicability and accessibility. In response to these challenges, various electrochemical methods leveraging nanotechnology have been documented. In this concise review, we endeavor to delineate the deficiencies associated with established conventional methodologies while accentuating the distinctive attributes and benefits inherent to contemporary biosensors. We place particular emphasis on elucidating the pivotal advancements and recent breakthroughs in the realm of nanotechnology-facilitated biosensors for the detection of PCOS.

Continuous and Non-Invasive Lactate Monitoring Techniques in Critical Care Patients

Lactate, once merely regarded as an indicator of tissue hypoxia and muscular fatigue, has now gained prominence as a pivotal biomarker across various medical disciplines. Recent research has unveiled its critical role as a high-value prognostic marker in critical care medicine. The current practice of lactate detection involves periodic blood sampling. This approach is invasive and confined to measurements at six-hour intervals, leading to resource expenditure, time consumption, and patient discomfort. This review addresses non-invasive sensors that enable continuous monitoring of lactate in critical care patients. After the introduction, it discusses the iontophoresis system, followed by a description of the structural materials that are universally employed to create an interface between the integumentary system and the sensor. Subsequently, each method is detailed according to its physical principle, outlining its advantages, limitations, and pertinent aspects. The study concludes with a discussion and conclusions, aiming at the design of an intelligent sensor (Internet of Medical Things or IoMT) to facilitate continuous lactate monitoring and enhance the clinical decision-making support system in critical care medicine.

Electrochemical Properties of PEDOT:PSS/Graphene Conductive Layers in Artificial Sweat

Electrodes based on PEDOT:PSS are gaining increasing importance as conductive electrodes and functional layers in various sensors and biosensors due to their easy processing and biocompatibility. This study investigates PEDOT:PSS/graphene layers deposited via spray coating on flexible PET substrates. The layers are characterized in terms of their morphology, roughness (via AFM and SEM), and electrochemical properties in artificial sweat using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The layers exhibit dominant capacitive behavior at low frequencies, with cut-off frequencies determined for thicker layers at 1 kHz. The equivalent circuit used to fit the EIS data reveals a resistance of about three orders of magnitude higher inside the layer compared to the charge transfer resistance at the solid/liquid interface. The capacitance values determined from the CV curves range from 54.3 to 122.0 mF m-2. After 500 CV cycles in a potential window of 1 V (from -0.3 to 0.7 V), capacitance retention for most layers is around 94%, with minimal surface changes being observed in the layers. The results suggest practical applications for PEDOT:PSS/graphene layers, both for high-frequency impedance measurements related to the functioning of individual organs and systems, such as impedance electrocardiography, impedance plethysmography, and respiratory monitoring, and as capacitive electrodes in the low-frequency range, realized as layered PEDOT:PSS/graphene conductive structures for biosignal recording.

Utilizing Electrochemical Biosensors as an Innovative Platform for the Rapid and On-Site Detection of Animal Viruses

Animal viruses are a significant threat to animal health and are easily spread across the globe with the rise of globalization. The limitations in diagnosing and treating animal virus infections have made the transmission of diseases and animal deaths unpredictable. Therefore, early diagnosis of animal virus infections is crucial to prevent the spread of diseases and reduce economic losses. To address the need for rapid diagnosis, electrochemical sensors have emerged as promising tools. Electrochemical methods present numerous benefits, including heightened sensitivity and selectivity, affordability, ease of use, portability, and rapid analysis, making them suitable for real-time virus detection. This paper focuses on the construction of electrochemical biosensors, as well as promising biosensor models, and expounds its advantages in virus detection, which is a promising research direction.

Electrochemical Sensing of Dopamine Using Polypyrrole/Molybdenum Oxide Bilayer-Modified ITO Electrode

The electrochemical sensing of biomarkers has attracted more and more attention due to the advantages of electrochemical biosensors, including their ease of use, excellent accuracy, and small analyte volumes. Thus, the electrochemical sensing of biomarkers has a potential application in early disease diagnosis diagnosis. Dopamine neurotransmitters have a vital role in the transmission of nerve impulses. Here, the fabrication of a polypyrrole/molybdenum dioxide nanoparticle (MoO3 NP)-modified ITO electrode based on a hydrothermal technique followed by electrochemical polymerization is reported. Several techniques were used to investigate the developed electrode's structure, morphology, and physical characteristics, including SEM, FTIR, EDX, N2 adsorption, and Raman spectroscopy. The results imply the formation of tiny MoO3 NPs with an average diameter of 29.01 nm. The developed electrode was used to determine low concentrations of dopamine neurotransmitters based on cyclic voltammetry and square wave voltammetry techniques. Furthermore, the developed electrode was used for monitoring dopamine in a human serum sample. The LOD for detecting dopamine by using MoO3 NPs/ITO electrodes based on the SWV technique was around 2.2 nmol L-1.

Biomedical applications of biodegradable polycaprolactone-functionalized magnetic iron oxides nanoparticles and their polymer nanocomposites

Magnetic nanoparticles (MNPs) have gained significant attention among several nanoscale materials during the last decade due to their unique properties. These properties make them successful nanofillers for drug delivery and a number of new biomedical applications. MNPs are more useful when combined with biodegradable polymers. In this review, we discussed the synthesis of polycaprolactones (PCL) and the various methods of synthesizing magnetic iron oxide nanoparticles. Then, the synthesis of composites that is made of PCL and magnetic materials (with special focus on iron oxide nanoparticles) were highlighted. In addition, we comprehensively reviewed their application in drug delivery, cancer treatment, wound healing, hyperthermia, and bone tissue engineering. Other biomedical applications of the magnetic PCL such as mitochondria targeting are highlighted. Moreover, biomedical applications of magnetic nanoparticles incorporated into other synthetic polymers apart from PCL are also discussed. Thus, great progress and better outcome with functionalized MNPs enhanced with polycaprolactone has been recorded with the biomedical applications of drug delivery and recovery of bone tissues.

Electrochemical and Spectroscopic (FTIR) Evidence of Conducting Polymer-Cu Ions Interaction

In this work, we provide electrochemical and spectroscopic evidence of the conducting polymer-heavy metal ion interaction by comparing the electrochemical and spectroscopic behavior (FTIR) of two different conducting polymer-modified electrodes based on 3,4-alkoxythiophenes: 3,4-ethylenedioxythiophene (EDOT) and ortho-xylen-3,4-dioxythiophene (XDOT) during the potentiodynamic stripping of copper. By analyzing the electrochemical and spectroscopic results, it is possible to propose two different copper dissolution processes during the electrochemical stripping process, which depend on the conducting polymer used. With PEDOT matrix, stripping occurs in a two-step pathway, observed as two anodic peaks, involving the formation of the Cu⁺-PEDOT complex and the subsequent oxidation step of the Cu⁺ complex to release Cu²⁺ ions. On the other side, the experiments carried out let us propose the formation of a poorly stable Cu²⁺-PXDOT complex or a superficial mechanism for the Cu²⁺ release, characterized by a single stripping signal for this process. Thus, the incorporation of Cu ions into the matrix and the stripping release are intimately related to the chemical structure of the polymer used.

Enhancing Electrochemical Biosensor Performance for 17β-Estradiol Determination with Short Split-Aptamers

Chronic exposure of 17β-estradiol (E2) even at low concentration can disorganize the endocrine system and lead to undesirable health problems in the long run. An electrochemical biosensor for rapid detection of E2 in water samples was successfully developed. The biosensor was based on split DNA aptamers attached onto poly (methacrylic acid-co-n butyl acrylate-succinimide) microspheres deposited on polypyrrole nanowires coated electrode (PPY/PMAA-NBA). The sandwich paired of split DNA aptamers used were truncated from 75 mer parent aptamers. These two strands of 12-mer and 14-mer split DNA aptamers were then immobilized on the PMAA-NBA microspheres. In the presence of E2, the split DNA aptamers formed an apt12-E2-apt14 complex, where the binding reaction on the electrode surface led to the detection of E2 by differential pulse voltammetry using ferrocyanide as a redox indicator. Under optimum conditions, the aptasensor detected E2 concentrations in the range of 1 × 10-4 M to 1 × 10-12 M (R2 = 0.9772) with a detection limit of 4.8 × 10-13 M. E2, which were successfully measured in a real sample with 97-104% recovery and showed a good correlation (R2 = 0.9999) with the established method, such as high-performance liquid chromatography. Interactions between short and sandwich-type aptamers (split aptamers) demonstrated improvement in aptasensor performance, especially the selectivity towards several potential interferents.

Poly(Thiophene)/Graphene Oxide-Modified Electrodes for Amperometric Glucose Biosensing

The availability of fast and non-expensive analytical methods for the determination of widespread interest analytes such as glucose is an object of large relevance; this is so not only in the field of analytical chemistry, but also in medicinal and in food chemistry. In this context, electrochemical biosensors have been proposed in different arrangements, according to the mode of electron transfer between the bioreceptor and the electrode. An efficient immobilization of an enzyme on the electrode surface is essential to assure satisfactory analytical performances of the biosensor in terms of sensitivity, limit of detection, selectivity, and linear range of employment. Here, we report the use of a thiophene monomer, (2,5-di(2-thienyl)thieno [3,2-b]thiophene (dTT-bT), as a precursor of an electrogenerated conducting film to immobilize the glucose oxidase (GOx) enzyme on Pt, glassy carbon (GC), and Au electrode surfaces. In addition, the polymer film electrochemically synthetized on a glassy carbon electrode was modified with graphene oxide before the deposition of GOx; the analytical performances of both the arrangements (without and with graphene oxide) in the glucose detection were compared. The biosensor containing graphene oxide showed satisfactory values of linear dynamic range (1.0-10 mM), limit of detection (0.036 mM), and sensitivity (9.4 µA mM^-1 cm^-2). Finally, it was tested in the determination of glucose in fruit juices; the interference from fructose, saccharose, and ascorbic acid was evaluated.

Electrodeposition and Characterization of Conducting Polymer Films Obtained from Carbazole and 2-(9H-carbazol-9-yl)acetic Acid

Electrochemical oxidation of electrolyte solutions containing carbazole (Cz) and 2-(9H-carbazol-9-yl)acetic acid (CzA) monomers was performed in acetonitrile solutions. Different Cz and CzA feed ratios were used to electrodeposit solid polymer films of various compositions, and to study the influence of the monomer ratio on the physicochemical properties (electroactivity, topography, adhesion, stiffness, wettability) of the polymer films. Thus, electrochemical oxidation led to the deposition of a solid film of micrometric thickness, but only for the solutions containing at least 30% of Cz. The proportion of Cz and CzA in the electrodeposited polymer films has little impact on the adhesion strength values measured by AFM. On the contrary, this proportion significantly modifies the stiffness of the films. Indeed, the stiffness of the polymer films varies from 9 to 24 GPa depending on the monomer ratio, which is much lower than the value obtained for unmodified polycarbazole (64 GPa). This leads to the absence of cracks in the films, which all have a fairly homogeneous globular structure. Moreover, among the different polymer films obtained, those prepared from 70:30 and 50:50 ratios in Cz:CzA monomer solutions seem to be the most interesting because these green films are conductive, thick, low in stiffness, do not show cracks and are resistant to prolonged immersion in water.

Recent Advances and Biomedical Applications of Peptide-Integrated Conducting Polymers

Conducting polymers (CPs) are of great interests to researchers around the world in biomedical applications owing to their unique electrical and mechanical properties. Besides, they are easy to fabricate and have long-term stability. These features make CPs a powerful building block of modern biomaterials. Peptide functionalization has been a versatile tool for the development of CP-based biomaterials. With the aid of peptide modifications, the biocompatibility, target selectivity, and cellular interactions of CPs can be greatly improved. Reflecting these aspects, an increasing number of studies on peptide-integrated conducting polymers have been reported recently. In this review, various kinds of peptide immobilization strategies on CPs are introduced. Moreover, the aims of peptide modification are discussed in three aspects: enhancing the specific selectivity, avoiding nonspecific adhesion, and mimicking the environment of extracellular matrix. We highlighted recent studies in the applications of peptide-integrated CPs in electrochemical sensors, antifouling surfaces, and conductive biointerfaces. These studies have shown great potentials from the integration of peptide and CPs as a versatile platform for advanced biological and clinical applications in the near future.

Fabrication of Polyaniline Ni-Complex Catalytic Electrode by Plasma Deposition for Electrochemical Detection of Phosphate through Glucose Redox Reaction as Mediator

We report here the preparation and characterization of polyaniline Ni-complex catalytic electrode by one-pot plasma deposition for the electrochemical detection of phosphate via the redox reaction of glucose. We first prepared a precursory solution by combining NiCl2 and 3-aminobenzoic acid in a mixed solution of methanol (MeOH) and water, and adding aniline as a conductive polymeric precursor for increasing the electron transfer potential. We then synthesized the catalytic electrode in a one-step cold plasma process by preparing the precursors on ITO glass. We characterized the obtained Ni-coordinate catalytic electrode via X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (SEM), and electrochemical methods. Electrochemical characterization produced stable redox properties of Ni3+/Ni2+ couples in a 0.1 M NaOH solution. Cyclic voltametric experiments have drastically increased electrocatalytic oxidation and reduction of glucose by increasing the concentration of phosphate (PO43−) ions using the prepared Ni-modified catalytic electrodes. From these results, the prepared catalytic electrode could be used as the electrochemical sensor for phosphate in actual water.

Fabrication of Hollow Nanocones Membrane with an Extraordinary Surface Area as CO2 Sucker

Recently, more and more attention has been paid to the development of eco-friendly solid sorbents that are cost-effective, noncorrosive, have a high gas capacity, and have low renewable energy for CO₂ capture. Here, we claimed the fabrication of a three-dimensional (3D) film of hollow nanocones with a large surface area (949.5 m²/g), a large contact angle of 136.3°, and high surface energy. The synthetic technique is based on an electrochemical polymerization process followed by a novel and simple strategy for pulling off the formed layers as a membrane. Although the polymer-coated substrates were reported previously, the membrane formation has not been reported elsewhere. The detachable capability of the manufactured layer as a membrane braked the previous boundaries and allows the membrane’s uses in a wide range of applications. This 3D hollow nanocones membrane offer advantages over conventional ones in that they combine a π-electron-rich (aromatic ring), hydrophobicity, a large surface area, multiple amino groups, and a large pore volume. These substantial features are vital for CO₂ capturing and storage. Furthermore, the hydrophobicity characteristic and application of the formed polymer as a CO₂ sucker were investigated. These results demonstrated the potential of the synthesized 3D hollow polymer to be used for CO₂ capturing with a gas capacity of about 68 mg/g and regeneration ability without the need for heat up.

Corrosion protection properties of polypyrrole coatings formed onto 316 L SS from a solution containing molybdate and salicylate

The electrosynthesis of PPy films onto 316L stainless steel from nearly neutral and alkaline solutions containing molybdate and salicylate is reported. The corrosion behaviour of the coatings constituted by hollow rectangular microtubes was monitored in Ringer solution using open circuit potential measurements, polarization techniques and electrochemical impedance spectroscopy. The polymer formed in a solution of pH 8 was the most efficient in terms of corrosion protection. The coating significantly reduced the pitting corrosion of the substrate. The results were interpreted taking into consideration the polymer electroactivity, the galvanic interaction polypyrrole/substrate and the nature of dopants. Silver species were effectively immobilized onto the hollow rectangular-sectioned microtubes of PPy. The modified coatings demonstrated that they have a good bactericidal activity against Escherichia coli and they were also able to protect the substrate against corrosion in Ringer solution.

Polyaniline Nanofibers-Embedded Gold Nanoparticles Obtained by Template-Free Procedure with Immobilization Prospects

In this work, template-free nanostructured conducting polymers (nCPs)-embedded gold nanoparticles (AuNPs) from aniline, thiophene and 3,4-ethylenedioxythiophene have been prepared via a one-pot sonochemical method. The synthesis of the nanocomposite (nCPs-AuNPs) was achieved in a short period of time (5-10 min), by applying high-energy ultrasound to an aqueous mixture of a CP precursor monomer and KAuCl4, in the presence of LiClO4 as dopant. The synthesis process is simpler, greener and faster in comparison to other procedures reported in the literature. Remarkably, bulk quantities of doped polyaniline PANI-AuNPs nanofibers were obtained. Subsequently, they were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and Fourier transform infrared spectroscopy (FTIR), as well as by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). PANI-AuNPs nanofibers were also employed as immobilization matrix for a benchmark enzyme, glucose oxidase (GOX). Finally, glucose was determined in real samples of white and red wines by using the so-obtained GOX-PANI-AuNPs/Sonogel-Carbon biosensor, providing outstanding recoveries (99.54%). This work may offer important insights into the synthesis of nanostructured conducting polymers and also stimulates the exploration of the applications of these nanocomposites, especially in research fields such as (bio)sensors, catalysis and composite materials.

Biocompatible Osmium Telluride-Polypyrrole Nanocomposite Material: Application in Prostate Specific Antigen Immunosensing

Prostate cancer is a dominant global threat to society. It affects nearly 4000 men in South Africa annually, making it the second most threatening cancerous disease after lung cancer. A potential serological biomarker to monitor early diagnosis of prostate cancer is prostate specific antigen (PSA). We used the PSA biomarker in our work to develop an extremely sensitive electrochemical immunosensor to achieve low detection limits. The fabrication steps followed with the combination of thioglycolic acid capped osmium telluride quantum dots (TGA-OsTe2QD)-polypyrrole (PPy) nanocomposite and prostate specific antigen modified on a glassy carbon electrode. The UV-Vis signatures of TGA-OsTe2QD-PPy showed an absorption band at 262 nm which is attributed to the PPy and TGA-OsTe2QD composite. This band corresponds to the energy band gap of 4.4 and 5.4 eV. The CV responses of BSA|Ab|TGA-OsTe2QD|PPy|GCE modified electrode to prostate specific antigen (PSA) was studied within a range of 0–16 ng/mL PSA that was linear, herein referred to as liner range (LR), which produced a limit of detection (LOD) value of 0.36 ng/mL PSA. The values of the immunosensor’s calibration parameters (LR and LOD) make them suitable for real sample application, due to their coverage of the PSA concentration range (0–14 ng/mL) that is of clinical importance.

Smart Materials Enabled with Artificial Intelligence for Healthcare Wearables

Contemporary medicine suffers from many shortcomings in terms of successful disease diagnosis and treatment, both of which rely on detection capacity and timing. The lack of effective, reliable, and affordable detection and real‐time monitoring limits the affordability of timely diagnosis and treatment. A new frontier that overcomes these challenges relies on smart health monitoring systems that combine wearable sensors and an analytical modulus. This review presents the latest advances in smart materials for the development of multifunctional wearable sensors while providing a bird's eye‐view of their characteristics, functions, and applications. The review also presents the state‐of‐the‐art on wearables fitted with artificial intelligence (AI) and support systems for clinical decision in early detection and accurate diagnosis of disorders. The ongoing challenges and future prospects for providing personal healthcare with AI‐assisted support systems relating to clinical decisions are presented and discussed.

Amino acid derived biopolymers: Recent advances and biomedical applications

Over the past few years, amino acids (AA) have emerged as promising biomaterials for the synthesis of functional polymers. Owing to the diversity of functional groups in amino acids, various polymerization methods may be used to make a wide range of well-defined functional amino-acid/peptide-based optically active polymers with varying polymer lengths, compositions, and designs. When incorporated with chirality and self-assembly, they offer a wide range of applications and are particularly appealing in the field of drug delivery, tissue engineering, and biosensing. There are several classes of these polymers that include polyamides (PA), polyesters (PE), poly(ester-amide)s (PEA)s, polyurethanes (PU)s, poly(depsipeptide)s (PDP)s, etc. They offer the ability to control functionality, conjugation, crosslinking, stimuli responsiveness, and tuneable mechanical/thermal properties. In this review, we present the recent advancements in the synthesis strategies for obtaining these amino acid-derived bio-macromolecules, their self-assembly properties, and the wealth of prevalent applications.

Use of electroconductive biomaterials for engineering tissues by 3D printing and 3D bioprinting

Existing methods of engineering alternatives to restore or replace damaged or lost tissues are not satisfactory due to the lack of suitable constructs that can fit precisely, function properly and integrate into host tissues. Recently, three-dimensional (3D) bioprinting approaches have been developed to enable the fabrication of pre-programmed synthetic tissue constructs that have precise geometries and controlled cellular composition and spatial distribution. New bioinks with electroconductive properties have the potential to influence cellular fates and function for directed healing of different tissue types including bone, heart and nervous tissue with the possibility of improved outcomes. In the present paper, we review the use of electroconductive biomaterials for the engineering of tissues via 3D printing and 3D bioprinting. Despite significant advances, there remain challenges to effective tissue replacement and we address these challenges and describe new approaches to advanced tissue engineering.

Effect of Electrosynthesis Potential on Nucleation, Growth, Adhesion, and Electronic Properties of Polypyrrole Thin Films on Fluorine-Doped Tin Oxide (FTO)

Polypyrrole (PPy) is one of the most attractive conducting polymers for thin film applications due to its good electrical conductivity, stability, optical properties, and biocompatibility. Among the technologies in which PPy has gained prominence are optoelectronics and solar energy conversion, where transparent electrodes such as fluorine-doped tin oxide (FTO) or indium tin oxide (ITO) are frequently used. However, FTO substrates have the notable advantage that their components are widely available in nature, unlike those of ITO. Recognizing the importance that the FTO/polypyrrole system has gained in various applications, here, we studied for the first time the nucleation and growth mechanism of electro-synthesized PPy on FTO. Additionally, the effect of the synthesis potential (0.9, 1.0, 1.1, and 1.2 V vs. Ag/AgCl) on the homogeneity, adhesion, conductivity, and HOMO energy levels of PPy films was determined. From current–time transients and scanning electron microscopy, it was found that films synthesized at 0.9 and 1.0 V exhibit 3D growth with progressive nucleation (as well as lower homogeneity and higher adhesion to FTO). In contrast, films synthesized at 1.1 and 1.2 V follow 2D growth with instantaneous nucleation. It was also evident that increasing the polymerization potential leads to polymers with lower conductivity and more negative HOMO levels (versus vacuum). These findings are relevant to encourage the use of electro-synthesized PPy in thin film applications that require a high control of material properties.

A comprehensive review on the applications of nano-biosensor-based approaches for non-communicable and communicable disease detection

The outstretched applications of biosensors in diverse domains has become the reason for their attraction for scientific communities. Because they are analytical devices, they can detect both quantitative and qualitative biological components through the generation of detectable signals. In the recent past, biosensors witnessed significant changes and developments in their design as well as features. Nanotechnology has revolutionized sensing phenomena by increasing biodiagnostic capacity in terms of specificity, size, and cost, resulting in exceptional sensitivity and flexibility. The steep increase of non-communicable diseases across the world has emerged as a matter of concern. In parallel, the abrupt outbreak of communicable diseases poses a serious threat to mankind. For decreasing the morbidity and mortality associated with various communicable and non-communicable diseases, early detection and subsequent treatment are indispensable. Detection of different biological markers generates quantifiable signals that can be electrochemical, mass-based, optical, thermal, or piezoelectric. Speculating on the incumbent applicability and versatility of nano-biosensors in large disciplines, this review highlights different types of biosensors along with their components and detection mechanisms. Moreover, it deals with the current advancements made in biosensors and the applications of nano-biosensors in detection of various non-communicable and communicable diseases, as well as future prospects of nano-biosensors for diagnostics.

Polyphenazine and polytriphenylmethane redox polymer/nanomaterial-based electrochemical sensors and biosensors: a review

In recent years, an increasing number of studies has demonstrated that redox polymers can be used in simple and effective electrochemical sensing platforms due to their fast electron transfer and electrocatalytic ability. To develop more sensitive and selective electrochemical (bio)sensors, the electrocatalytic properties of redox polymers and the electrical, mechanical, and catalytic properties of various nanomaterials are combined. This review aims to summarize and contribute to the development of (bio)sensors based on polyphenazine or polytriphenylmethane redox polymers combined with nanomaterials, including carbon-based nanomaterials, metal/metal oxide, and semiconductor nanoparticles. The synthesis, preparation, and modification of these nanocomposites is presented and the contribution of each material to the performance of (bio)sensor has been be examined. It is explained how the combined use of these redox polymers and nanomaterials as a sensing platform leads to improved analytical performance of the (bio)sensors. Finally, the analytical performance characteristics and practical applications of polyphenazine and polytriphenylmethane redox polymer/nanomaterial-based electrochemical (bio)sensors are compared and discussed.

Application of PEDOT:PSS and Its Composites in Electrochemical and Electronic Chemosensors

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) is a highly important and attractive conducting polymer as well as commercially available in organic electronics, including electrochemical and electronic chemosensors, due to its unique features such as excellent solution-fabrication capability and miscibility, high and controllable conductivity, excellent chemical and electrochemical stability, good optical transparency and biocompatibility. In this review, we present a comprehensive overview of the recent research progress of PEDOT:PSS and its composites, and the application in electrochemical and electronic sensors for detecting liquid-phase or gaseous chemical analytes, including inorganic or organic ions, pH, humidity, hydrogen peroxide (H2O2), ammonia (NH3), CO, CO2, NO2, and organic solvent vapors like methanol, acetone, etc. We will discuss in detail the structural, architectural and morphological optimization of PEDOT:PSS and its composites with other additives, as well as the fabrication technology of diverse sensor systems in response to a wide range of analytes in varying environments. At the end of the review will be given a perspective summary covering both the key challenges and potential solutions in the future research of PEDOT:PSS-based chemosensors, especially those in a flexible or wearable format.

Novel Semi-Interpenetrated Polymer Networks of Poly(3-Hydroxybutyrate-co-3-Hydroxyvalerate)/Poly (Vinyl Alcohol) with Incorporated Conductive Polypyrrole Nanoparticles

This paper reports the preparation and characterization of semi-interpenetrating polymer networks (semi-IPN) of poly(3-hydroxybutirate-co-3-hydroxyvalerate), PHBV, and poly (vinyl alcohol), PVA, with conductive polypirrole (PPy) nanoparticles. Stable hybrid semi-IPN (PHBV/PVA 30/70 ratio) hydrogels were produced by solvent casting, dissolving each polymer in chloroform and 1-methyl-2-pyrrolidone respectively, and subsequent glutaraldehyde crosslinking of the PVA chains. The microstructure and physical properties of this novel polymeric system were analysed, including thermal behaviour and degradation, water sorption, wettability and electrical conductivity. The conductivity of these advanced networks rose significantly at higher PPy nanoparticles content. Fourier transform infrared spectroscopy (FTIR) and calorimetry characterization indicated good miscibility and compatibility between all the constituents, with no phase separation and strong interactions between phases. A single glass transition was observed between those of pure PHBV and PVA, although PVA was dominant in its contribution to the glass transition process. Incorporating PPy nanoparticles significantly reduced the hydrogel swelling, even at low concentrations, indicating molecular interactions between the PPy nanoparticles and the hydrogel matrix. The PHBV/PVA semi-IPN showed higher thermal stability than the neat polymers and PHBV/PVA blend, which also remained in the tertiary systems.

Electro-responsive hydrogels: macromolecular and supramolecular approaches in the biomedical field

Hydrogels are soft materials of the utmost importance in the biomedical and healthcare fields. Two approaches can be considered to obtain such biomaterials: the macromolecular one and the supramolecular one. In the first, the chemical gel is based on crosslinking while in the second the physical hydrogel is stabilized thanks to noncovalent interactions. Recently, new trends rely on smart devices able to modify their physico-chemical properties under stimulation. Such stimuli-responsive systems can react to internal (i.e. pH, redox potential, enzyme, etc.) or external (i.e. magnetic field, light, electric field, etc.) triggers leading to smart drug release and drug delivery systems, 3D scaffolds or biosensors. Even if some stimuli-responsive biomaterials are currently widely studied, other ones represent a real challenge. Among them, electro-responsive hydrogels, especially obtained via supramolecular approach, are under-developped leaving room for improvement. Indeed, currently known macromolecular electro-responsive systems are reaching some limitations related to their chemical composition, physicochemical properties, mechanical strength, processing technologies, etc. In contrast, the interest for supramolecular hydrogels has risen for the past few years suggesting that they may provide new solutions as electro-responsive soft materials. In this short review, we give a recent non exhaustive survey on macromolecular and supramolecular approaches for electro-responsive hydrogels in the biomedical field.

Polymers and Plastics Modified Electrodes for Biosensors: A Review

Polymer materials offer several advantages as supports of biosensing platforms in terms of flexibility, weight, conformability, portability, cost, disposability and scope for integration. The present study reviews the field of electrochemical biosensors fabricated on modified plastics and polymers, focusing the attention, in the first part, on modified conducting polymers to improve sensitivity, selectivity, biocompatibility and mechanical properties, whereas the second part is dedicated to modified "environmentally friendly" polymers to improve the electrical properties. These ecofriendly polymers are divided into three main classes: bioplastics made from natural sources, biodegradable plastics made from traditional petrochemicals and eco/recycled plastics, which are made from recycled plastic materials rather than from raw petrochemicals. Finally, flexible and wearable lab-on-a-chip (LOC) biosensing devices, based on plastic supports, are also discussed. This review is timely due to the significant advances achieved over the last few years in the area of electrochemical biosensors based on modified polymers and aims to direct the readers to emerging trends in this field.