Mass Spectrometric Analysis of Bisphenol A Desorption from Titania Nanoparticles: Ammonium Acetate, Fluoride, Formate, and Hydroxide as Chemical Desorption Agents

Chitosan/Gold Nanoparticles Nanocomposite Film for Bisphenol A Electrochemical Sensing

Bisphenol A (BPA) is considered an endocrine-disrupting compound and can cause toxicological effects, even at low doses. The development of sensitive and reliable sensors that would allow the detection of such contaminant is highly pursued. Herein, we report an electrochemical sensing strategy based on a simple and low-cost nanocomposite film sensor platform for BPA detection. The platform was developed by modifying a fluorine-doped tin oxide (FTO) electrode with layer-by-layer (LbL) films of chitosan (Chi) and gold nanoparticles functionalized with a polythiophene derivative (AuNPs:PTS). The growth of the Chi/AuNPs:PTS LbL films was monitored by UV–Vis spectroscopy. Electrochemical characterization revealed that the three-bilayer film exhibited the highest electrocatalytic performance and differential-pulse voltammetry (DPV) measurements demonstrated that the modified electrode was suitable for BPA detection through a quasi-reversible and adsorption-controlled electrochemical oxidation and reduction process. The developed sensor exhibited a linear response range from 0.4 to 20 μmol L−1, with a detection limit of 0.32 μmol L−1. The sensor showed good reproducibility with relative standard deviations of 2.12% and 3.73% to intra- and inter-electrode, respectively. Furthermore, the platform demonstrated to be suitable to detect BPA in real water samples, as well as selective for BPA detection in solutions with 100-fold excess of common interfering compounds.

Polyaniline-Coated TiO2 Nanorods for Photocatalytic Degradation of Bisphenol A in Water

Polyaniline (PANI)-wrapped TiO₂ nanorods (PANI/TiO₂), obtained through the oxidative polymerization of aniline at the surface of hydrothermally presynthesized TiO₂ nanorods, were evaluated as photocatalysts for the degradation of Bisphenol A (BPA). Fourier-transform infrared spectroscopy analysis revealed the successful incorporation of PANI into TiO₂ by the appearance of peaks at 1577 and 1502 cm^-1 that are due to the C=C and C-N stretch of the benzenoid or quinoid ring in PANI. Brunauer-Emmett-Teller analysis revealed that PANI/TiO₂ had almost double the surface area of TiO₂ (44.8999 m²/g vs 28.2179 m²/g). Transmission electron microscopy (TEM) analysis showed that TiO₂ nanorods with different diameters were synthesized. The TEM analysis showed that a thin layer of PANI wrapped the TiO₂ nanorods. X-ray photon spectroscopy survey scan of the PANI/TiO₂ nanocomposite revealed the presence of C, O, Ti, and N. Photocatalytic activity evaluation under UV radiation through the effect of key parameters, including pH, contact time, dosage, and initial concentration of BPA, was carried out in batch studies. Within 80 min, 99.7% of 5 ppm BPA was attained using the 0.2 g/L PANI/TiO₂ photocatalyst at pH 10. The quantum yield (QY) of these photocatalysts was evaluated to be 9.86 × 10^-5 molecules/photon and 2.82 × 10^-5 molecules/photon for PANI/TiO₂ and TiO₂, respectively. PANI/TiO₂ showed better performance than as-synthesized TiO₂ with a rate constant of 4.46 × 10^-2 min^-1 compared to 2.18 × 10^-2 min^-1. The rate of degradation of PANI/TiO₂ was also superior to that of TiO₂ (150 mmol/g/h vs 74.89 mmol/g/h). Nitrate ions increased the rate of degradation of BPA, while humic acid consistently inhibited the degradation of BPA. LC-MS analysis identified degradation products with m/z 213.1, 135.1, and 93.1. The PANI/TiO₂ nanocomposite was reused up to five cycles with a removal of at least 80% in the fifth cycle. LC-MS results revealed three possible BPA degradation intermediates. LC-MS analysis identified degradation products which included protonated BPA, [C₁₄H₁₃O₂ ⁺], and [C₉H₁₁O⁺]. The PANI/TiO₂ nanocomposite demonstrated superior photocatalytic activity with respect to improved QY and figure of merit and lower energy consumption.

Ion-Trap Mass Spectrometric Analysis of Bisphenol A Interactions With Titanium Dioxide Nanoparticles and Milk Proteins

Quantitative analysis of endocrine-disrupting molecules such as bisphenol A (BPA) in freshwater to determine their widespread occurrence in environmental resources has been challenged by various adsorption and desorption processes. In this work, ion trap mass spectrometry (ITMS) analysis of BPA was aimed at studying its molecular interactions with titanium dioxide (TiO2) nanoparticles and milk whey proteins. Addition of sodium formate prevented TiO2 nanoparticles from sedimentation while enhancing the electrospray ionization (ESI) efficiency to produce an abundance of [BPA + Na]+ ions at m/z 251.0. More importantly, the ESI-ITMS instrument could operate properly during a direct infusion of nanoparticles up to 500 μg/mL without clogging the intake capillary. Milk protein adsorption of BPA could decrease the [BPA + Na]+ peak intensity significantly unless the proteins were partially removed by curdling to produce whey, which allowed BPA desorption during ESI for quantitative analysis by ITMS.