New Prospects in the Electroanalysis of Heavy Metal Ions (Cd, Pb, Zn, Cu): Development and Application of Novel Electrode Surfaces

Preparation of pyridoxine-based polyurethane modified sensors and their use in simultaneous determination of Cu(II) - Co(II) ions

In this study, pyridoxine-based polyurethane-modified electrodes were prepared to simultaneously and sensitively measure copper (Cu(II)) and cobalt (Co(II)) ions in complex matrix samples. For the production of the electrodes, firstly, the synthesis of pyridoxine-based polyurethane structures was carried out. In these syntheses, the polymer structure was diversified by using different isocyanates. Polyethyleneglycol-200 (PEG), pyridoxine (B6), and β-cyclodextrin (β-CD) groups were used as the source of polyol. The synthesized polyurethane structures were characterized by different instrumental techniques and used in gold electrode surface modification. Modified sensor surfaces were examined by scanning electron microscopy and atomic force microscopy techniques. The prepared modified sensors were used for the simultaneous detection of Cu(II) and Co(II) ions using the differential pulse voltammetry technique. The limit of detection (LOD), limit of quantitation (LOQ), and R2 values for Cu(II) ions were calculated as 8.81 μM, 29.4 μM, and 0.993, respectively. LOD, LOQ, and R2 values for Co(II) ions were calculated as 9.84 μM, 32.8 μM, and 0.9935, respectively. For repeatability, the relative standard deviation (RSD %) of the prepared simultaneous sensors was determined as 1.54 and 1.71 for Cu(II) and Co(II), respectively. As a result, Cu(II) and Co(II) ions were measured independently and simultaneously with high sensitivity. According to these results, it is predicted that pyridoxine-based polyurethane-modified sensors may be suitable for the simultaneous detection of Cu(II) and Co(II) in medical, food, and agricultural samples.

Turn-On Solid-State Fluorescent Determination of Zinc Ion by Quinoline-Based Covalent Organic Framework

A new quinoline-based COF (covalent organic framework), obtained by Povarov reaction, containing 2,6-diisopropylphenyl moieties as substituents over the heterocyclic ring is described for detecting Zn2+ in aqueous solution. The introduction of the mentioned bulky phenyl rings into the network favors an increase of the distance between the reticular sheets and their arrangement, obtaining a new material with an alternating AB type stacking. The new material exhibits good selectivity to detect Zn2+ by fluorescence emission in aqueous solutions up to a concentration of 1.2 × 10-4 m of the metal ion. In order to have a deeper insight into the interaction between the COF and the zinc cation, a thorough spectroscopical, microscopical, and theoretical study is also presented and discussed in this communication.

Emerging trends in functional materials for electrochemical sensors in nicotine determination

In the past year, there has been significant progress in the utilization of electrochemical strategies for the determination of harmful substances. Among those, the electrochemical determination of nicotine (NIC) has continued to be of significant interest ascribed to the global health concern of e-cigarette products, nowadays. Electrochemical sensors have become promising tools for the detection of NIC ascribed to their high sensitivity, selectivity, and ease of use. This review article provides a concise overview of the advanced developments in electrochemical sensors for NIC detection using modified functional materials such as carbon-based materials, metal-organic frameworks (MOF), MXene, polymer, and metallic based modifiers. The sensitivity of electrochemical sensors can be improved by modifying them with these conductive materials ascribed to their physical and chemical properties. The review also addresses the challenges and future perspectives in the field, including sensitivity and selectivity improvements, stability and reproducibility issues, integration with data analysis techniques, and emerging trends. In conclusion, this review article may be of interest to researchers intending to delve into the development of functional electrochemical sensors in future studies.

Bismuth Film along with dsDNA-Modified Electrode Surfaces as Promising (bio)Sensors in the Analysis of Heavy Metals in Soils

Heavy metals constitute pollutants that are particularly common in air, water, and soil. They are present in both urban and rural environments, on land, and in marine ecosystems, where they cause serious environmental problems since they do not degrade easily, remain almost unchanged for long periods, and bioaccumulate. The detection and especially the quantification of metals require a systematic process. Regular monitoring is necessary because of seasonal variations in metal levels. Consequently, there is a significant need for rapid and low-cost metal determination methods. In this study, we compare and analytically validate absorption spectrometry with a sensitive voltammetric method, which uses a bismuth film-plated electrode surface and applies stripping voltammetry. Atomic absorption spectroscopy (AAS) represents a well-established analytical technique, while the applicability of anodic stripping voltammetry (ASV) in complicated sample matrices such as soil samples is currently unknown. This sample-handling challenge is investigated in the present study. The results show that the AAS and ASV methods were satisfactorily correlated and showed that the metal concentration in soils was lower than the limit values but with an increasing trend. Therefore, continuous monitoring of metal levels in the urban complex of a city is necessary and a matter of great importance. The limits of detection of cadmium (Cd) were lower when using the stripping voltammetry (SWASV) graphite furnace technique compared with those obtained with AAS when using the graphite furnace. However, when using flame atomic absorption spectroscopy (flame-AAS), the measurements tended to overestimate the concentration of Cd compared with the values found using SWASV. This highlights the differences in sensitivity and accuracy between these analytical methods for detecting Cd. The SWASV method has the advantage of being cheaper and faster, enabling the simultaneous determination of heavy elements across the range of concentrations that these elements can occur in Mediterranean soils. Additionally, a dsDNA biosensor is suggested for the discrimination of Cu(I) along with Cu(II) based on the oxidation peak of guanine, and adenine residues can be applied in the redox speciation analysis of copper in soil, which represents an issue of great importance.

Electrochemical Sensors for Heavy Metal Ion Detection in Aqueous Medium: A Systematic Review

Heavy metal ions (HMIs) are very harmful to the ecosystem when they are present in excess of the recommended limits. They are carcinogenic in nature and can cause serious health issues. So, it is important to detect the metal ions quickly and accurately. The metal ions arsenic (As3+), cadmium (Cd2+), chromium (Cr3+), lead (Pb2+), and mercury (Hg2+) are considered to be very toxic among other metal ions. Standard analytical methods like atomic absorption spectroscopy, atomic fluorescence spectroscopy, and X-ray fluorescence spectroscopy are used to detect HMIs. But these methods necessitate highly technical equipment and lengthy procedures with skilled personnel. So, electrochemical sensing methods are considered to be more advantageous because of their quick analysis with precision and simplicity to operate. They can detect a wide range of heavy metals providing real-time monitoring and are cost-effective and enable multiparametric detection. Various sensing applications necessitate severe regulation regarding the modification of electrode surfaces. Numerous nanomaterials such as graphene, carbon nanotubes, and metal nanoparticles have been extensively explored as interface materials in electrode modifiers. These nanoparticles offer excellent electrical conductivity, distinctive catalytic properties, and high surface area resulting in enhanced electrochemical performance. This review examines different HMI detection methods in an aqueous medium by an electrochemical sensing approach and studies the recent developments in interface materials for altering the electrodes.

Screen-Printed Sensors Modified with Nafion and Mesoporous Carbon for Electrochemical Detection of Lead in Blood

Lead (Pb) has long been acknowledged as a systemic toxicant, with pronounced health impacts observed even at low exposure levels, particularly in children. Adverse effects include diminished cognitive function, altered behavior, and developmental delays. Consequently, it is imperative to conduct regular monitoring of Blood Lead Levels (BLLs). In this work, we report on an electrochemical sensor based on screen-printed carbon electrode (SPCE) coated with Nafion and mesoporous carbon (MC). The sensor system uses simple sample preparation (acidification and dilution of whole blood), minimal sample volume (a few blood drops, 200 μl), and swift time-to-results (1 h). A limit of quantitation (LOQ) of 0.3 μg dL-1 Pb was achieved in whole blood. To demonstrate the practical utility of our sensor system, we evaluated its performance in the analysis of blood samples collected from children (n = 25). Comparative analysis with the laboratory-based gold standard method of inductively coupled plasma mass spectrometry (ICP-MS) demonstrated approximately 77% accuracy and 94% precision. We anticipate that our approach will serve as a valuable tool for more frequent BLL monitoring, particularly in communities where access to laboratory testing is impractical or expensive.