An Emerging Visible-Light Organic-Inorganic Hybrid Perovskite for Photocatalytic Applications

Photocatalytic removal of toxic dyes, liquorice and tetracycline wastewaters by a mesoporous photocatalyst under irradiation of different lamps and sunlight

Simple recyclable K₅CoW₁₂O₄₀/TiO₂ was synthesized and used to remove methyl orange, rhodamine B, direct red 16 and crystal violet toxic organic dyes, liquorice industrial wastewater and tetracycline (TC) as an antibiotic. Photoactivity of the catalyst was checked out under irradiation of various lamps (such as 18 W fluorescent, 300 W Xenon, LED and IR lamps). The best efficiency was obtained by fluorescent lamp at catalyst loading of 3 g/L, initial pH of 5, initial dye concentration of 5 ppm, complete degradation was achieved after 30 min contact time. Mechanistic investigation showed that·O₂ radicals and h⁺ are majorly responsible for photodegradation in this process. Electrochemical investigation, Nyquist, Bode, Mott-Schottky, Tauc plots and photoluminescence proved that using this photocatalyst delay the electron-hole recombination, increase the lifetime of excited electron, extend light absorption to visible region and improve the light absorption capacity. This photocatalyst work well under winter sunlight. Also 97% and 84% dye removal was obtained for liquorice with 300 and 1000 COD at optimal condition. This catalyst showed similar activity for TC wastewater. Photocatalyst was characterized by FE-SEM, EDX, AFM, FT-IR, XRD, PL, DRS, EIS, BJH and BET.

Complex Catalytic Materials Based on the Perovskite-Type Structure for Energy and Environmental Applications

This review paper focuses on perovskite-type materials as (photo)catalysts for energy and environmental applications. After a short introduction and the description of the structure of inorganic and hybrid organic-inorganic perovskites, the methods of preparation of inorganic perovskites both as powders via chemical routes and as thin films via laser-based techniques are tackled with, for the first, an analysis of the influence of the preparation method on the specific surface area of the material obtained. Then, the (photo)catalytic applications of the perovskites in energy production either in the form of hydrogen via water photodecomposition or by methane combustion, and in the removal of organic pollutants from waste waters, are reviewed.

Boosted insights of novel accordion-like (2D/2D) hybrid photocatalyst for the removal of cationic dyes: Mechanistic and degradation pathways

In the present work, a novel (2D/2D) accordion like CS@g‒C₃N₄/MX hybrid composite was prepared through one-pot hydro-thermal synthesis method and utilized as a catalyst for the degradation of organic persistent dyes such as methylene blue (MB) and rhodamine B (RhB). Because the removal of such organic compounds is a major dispute in environmental aspects. In this study, the bio-assisted g‒C₃N₄/MX nanosheets was utilized for the removal of organic dyes from aqueous solution under visible light irradiation, respectively. The CS@g-C₃N₄/MX photocatalyst showed high catalytic activity based on ~99% and ~98.5% degradation of MB and RhB within 60 and 40 min using visible light irradiation. This outcome could have resulted in greater catalytic enactment towards the degradation of other persistent pollutants with enhanced light absorption property and it can efficiently suppress photo-generated charge recombination, thus improving the interfacial charge transfer rate. The OH radical was being effective oxidative species involved in the CS@g-C₃N₄/MX system for the degradation of organic contaminants. Furthermore, CS@g-C₃N₄/MX showed excellent photo-stability over five consecutive cycles for the degradation of organic dyes with negligible loss of photocatalytic activity. Finally, the purposed catalytic mechanisms and degradation pathways of MB and RhB were systematically discussed in detail based on experimental results. Thus, the organics which oxidized into ring-opened compounds such as ethoxyethane, butadiene etc., to non-toxic products like H₂O, CO₂ and some mineral salts.

Recent Progresses on Metal Halide Perovskite-Based Material as Potential Photocatalyst

Recent years have witnessed an incredibly high interest in perovskite-based materials. Among this class, metal halide perovskites (MHPs) have attracted a lot of attention due to their easy preparation and excellent opto-electronic properties, showing a remarkably fast development in a few decades, particularly in solar light-driven applications. The high extinction coefficients, the optimal band gaps, the high photoluminescence quantum yields and the long electron–hole diffusion lengths make MHPs promising candidates in several technologies. Currently, the researchers have been focusing their attention on MHPs-based solar cells, light-emitting diodes, photodetectors, lasers, X-ray detectors and luminescent solar concentrators. In our review, we firstly present a brief introduction on the recent discoveries and on the remarkable properties of metal halide perovskites, followed by a summary of some of their more traditional and representative applications. In particular, the core of this work was to examine the recent progresses of MHPs-based materials in photocatalytic applications. We summarize some recent developments of hybrid organic–inorganic and all-inorganic MHPs, recently used as photocatalysts for hydrogen evolution, carbon dioxide reduction, organic contaminant degradation and organic synthesis. Finally, the main limitations and the future potential of this new generation of materials have been discussed.

Effects of Annealing on Characteristics of Cu2ZnSnSe4/CH3NH3PbI3/ZnS/IZO Nanostructures for Enhanced Photovoltaic Solar Cells

This paper presents new photovoltaic solar cells with Cu₂ZnSnSe₄/CH₃NH₃PbI₃(MAPbI₃)/ZnS/IZO/Ag nanostructures on bi-layer Mo/FTO (fluorine-doped tin oxide) glasssubstrates. The hole-transporting layer, active absorber layer, electron-transporting layer, transparent-conductive oxide layer, and top electrode-metal contact layer, were made of Cu₂ZnSnSe₄, MAPbI₃ perovskite, zincsulfide, indium-doped zinc oxide, and silver, respectively. The active absorber MAPbI₃ perovskite film was deposited on Cu₂ZnSnSe₄ hole-transporting layer that has been annealed at different temperatures. TheseCu₂ZnSnSe₄ filmsexhibitedthe morphology with increased crystal grain sizesand reduced pinholes, following the increased annealing temperature. When the perovskitefilm thickness was designed at 700 nm, the Cu₂ZnSnSe₄ hole-transporting layer was 160 nm, and the IZO (indium-zinc oxide) at 100 nm, and annealed at 650 °C, the experimental results showed significant improvements in the solar cell characteristics. The open-circuit voltage was increased to 1.1 V, the short-circuit current was improved to 20.8 mA/cm², and the device fill factor was elevated to 76.3%. In addition, the device power-conversion efficiency has been improved to 17.4%. The output power P_max was as good as 1.74 mW and the device series-resistance was 17.1 Ω.