The Applicability of a Drop Penetration Method to Measure Contact Angles on TiO2 and ZnO Nanoparticles

Use of Polycaprolactone Electrospun Nanofiber Mesh in a Face Mask

Electrospun nanofiber mesh has previously been used as an air filtration device. However, the qualification of polycaprolactone (PCL) nanofiber mesh cloth in face masks to protect individuals against airborne particles carrying microorganisms has yet to be investigated. The long-term goal of this study is to develop methods to use PCL nanofiber mesh to provide better protection against microorganisms. To achieve this goal, we observed the morphology, water droplet absorption, thermal (differential scanning calorimetry), mechanical, and airborne particle filtering capabilities, and also the microbial activities of a PCL cloth, to evaluate whether it is suitable to act as a filter in a face mask. We have produced a polycaprolactone (PCL) nanofiber cloth after electrospinning it onto a drum for 3 and 10 min, referred to hereafter as PCL-3 and PCL-10, respectively. Our study found that the middle protection layer (control) of the Henry Schein Earloop Procedure Mask contains pores (average diameter = 5.72 ± 0.62 µm) which are 48 times larger than the diameter of a microorganism an average diameter of ~120 nanometers. However, PCL-10 nanofiber membranes show pores with an average diameter of 1.42 ± 0.34 µm. Our contact angle measurement tests found that all the samples were very hydrophobic (contact angle values varied between 120 and 150 degrees). However, both PCL cloths' contact angle values were lower compared to the control. The produced PCL cloths showed a lower water droplet absorption compared to the control. Thermal studies found that PCL is stable in extreme conditions and no plasticizing effect occurs due to the presence of a solvent. Mechanical tests showed that PCL-10 cloth had higher strength and modulus compared to the control and PCL-3 under tension loading conditions. A vacuum experiment found that the PCL-10 fiber cloth could withstand a negative pressure of 18 Psi without any signs of breakage, and the mask was able to capture airborne particles and microorganisms. The feasibility of immobilizing anti-bacterial nanoparticles with PCL during electrospinning creates the future potential of producing an anti-bacterial face mask using PCL.

Hydrophobic/Oleophilic Structures Based on MacroPorous Silicon: Effect of Topography and Fluoroalkyl Silane Functionalization on Wettability

The effect of the morphology and chemical composition of a surface on the wettability of porous silicon structures is analyzed in the present work. Hydrophobic and superhydrophobic macroporous substrates are attractive for different potential applications. Herein, different hydrophobic macroporous silicon structures were fabricated by the chemical etching of p-type silicon wafers in a solution based on hydrofluoric acid and coated with a fluoro silane self-assembled monolayer. The surface morphology of the final substrate was characterized using a scanning electron microscope. The wettability was assessed from contact angle measurements using water and organic solvents that present low surface energy. The experimental data were compared with the classical wetting states theoretical models described in the literature. Perfluoro-silane functionalized macroporous silicon surfaces presented systematically higher contact angles than untreated silicon substrates. The influence of porosity on the surface wettability of macoporous silicon structures has been established. These results suggest that the combination of etching conditions with a surface chemistry modification could lead to hydrophobic/oleophilic or superhydrophobic/oleophobic structures.

The influence of hydrophobicity on Fischer-Tropsch synthesis catalysts

We review scientific works carried out on the influence of surface hydrophobicity on activity and product selectivity of supported cobalt and iron catalysts during Fischer-Tropsch synthesis (FTS). The characteristics of the surface of catalyst support may influence metal-support interactions, which leads to various degrees of metal dispersion and reducibility. Also, these support surface properties may influence the mass transfer of reactants and products at the catalyst active sites and subsequently affects the performance of the catalyst during FTS. Pre-silylated and post-silylated catalysts have been used to study the influence of surface hydrophobicity on the performance of FTS catalysts. The enhancement of FTS activity by hydrophobicity was mainly ascribed to the improved reducibility of metal oxide species. Furthermore, post-silylated supported iron catalysts favoured the suppression of water-gas shift (WGS) reaction, thereby hindering CO2 formation.

Surface Wettability of ZnO-Loaded TiO2 Nanotube Array Layers

Herein we report on the synthesis and the effects of gradual loading of TiO₂ nanotube array layers with ZnO upon surface wettability. Two-step preparation was chosen, where TiO₂ nanotube layers, grown in a first instance by anodization of a Ti foil, were gradually loaded with controlled amounts of ZnO using the reactive RF magnetron sputtering. After crystallization annealing, the formerly amorphous TiO₂ nanotubes were converted to predominantly anatase crystalline phase, as detected by XRD measurements. The as-prepared nanotubes exhibited a well-aligned columnar structure, 1.6 μm long and 88 nm in diameter, and a small concentration of oxygen vacancies. Ti²⁺ and Ti³⁺ occur along with the Ti⁴⁺ state upon sputter-cleaning the layer surfaces from contaminants. The Ti²⁺ and Ti³⁺ signals diminish with gradual ZnO loading. As demonstrated by the VB-XPS data, the ZnO loading is accompanied by a slight narrowing of the band gap of the materials. A combined effect of material modification and surface roughness was taken into consideration to explain the evolution of surface super-hydrophilicity of the materials under UV irradiation. The loading process resulted in increasing surface wettability with approx. 33%, and in a drastic extension of activation decay, which clearly points out to the effect of ZnO-TiO₂ heterojunctions.