Low Working Temperature of ZnO-MoS2 Nanocomposites for Delaying Aging with Good Acetylene Gas-Sensing Properties

Advances in 2D Materials Based Gas Sensors for Industrial Machine Olfactory Applications

The escalating development and improvement of gas sensing ability in industrial equipment, or "machine olfactory", propels the evolution of gas sensors toward enhanced sensitivity, selectivity, stability, power efficiency, cost-effectiveness, and longevity. Two-dimensional (2D) materials, distinguished by their atomic-thin profile, expansive specific surface area, remarkable mechanical strength, and surface tunability, hold significant potential for addressing the intricate challenges in gas sensing. However, a comprehensive review of 2D materials-based gas sensors for specific industrial applications is absent. This review delves into the recent advances in this field and highlights the potential applications in industrial machine olfaction. The main content encompasses industrial scenario characteristics, fundamental classification, enhancement methods, underlying mechanisms, and diverse gas sensing applications. Additionally, the challenges associated with transitioning 2D material gas sensors from laboratory development to industrialization and commercialization are addressed, and future-looking viewpoints on the evolution of next-generation intelligent gas sensory systems in the industrial sector are prospected.

Ppb-Level Hydrogen Sulfide Gas Sensor Based on the Nanocomposite of MoS2 Octahedron/ZnO-Zn2SnO4 Nanoparticles

Hydrogen sulfide (H2S) detection is extremely necessary due to its hazardous nature. Thus, the design of novel sensors to detect H2S gas at low temperatures is highly desirable. In this study, a series of nanocomposites based on MoS2 octahedrons and ZnO-Zn2SnO4 nanoparticles were synthesized through the hydrothermal method. Various characterizations such as X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectrum (XPS) have been used to verify the crystal phase, morphology and composition of synthesized nanocomposites. Three gas sensors based on the nanocomposites of pure ZnO-Zn2SnO4 (MS-ZNO-0), 5 wt% MoS2-ZnO-Zn2SnO4 (MS-ZNO-5) and 10 wt% MoS2-ZnO-Zn2SnO4 (MS-ZNO-10) were fabricated to check the gas sensing properties of various volatile organic compounds (VOCs). It showed that the gas sensor of (MS-ZNO-5) displayed the highest response of 4 to 2 ppm H2S and fewer responses to all other tested gases at 30 °C. The sensor of MS-ZNO-5 also displayed humble selectivity (1.6), good stability (35 days), promising reproducibility (5 cycles), rapid response/recovery times (10 s/6 s), a limit of detection (LOD) of 0.05 ppm H2S (Ra/Rg = 1.8) and an almost linear relationship between H2S concentration and response. Several elements such as the structure of MoS2, higher BET-specific surface area, n-n junction and improvement in oxygen species corresponded to improving response.

CTAB Enhanced Room-Temperature Detection of NO2 Based on MoS2-Reduced Graphene Oxide Nanohybrid

A new NO2 nanohybrid of a gas sensor (CTAB-MoS2/rGO) was constructed for sensitive room-temperature detection of NO2 by 3D molybdenum disulfide (MoS2) and reduced graphene oxide (rGO), assisted with hexadecyl trimethyl ammonium bromide (CTAB). In comparison with MoS2 and MoS2/rGO, the BET and SEM characterization results depicted the three-dimensional structure of the CTAB-MoS2/rGO nanohybrid, which possessed a larger specific surface area to provide more active reaction sites to boost its gas-sensing performance. Observations of the gas-sensing properties indicated that the CTAB-MoS2/rGO sensor performed a high response of 45.5% for 17.5 ppm NO2, a remarkable selectivity of NO2, an ultra-low detection limit of 26.55 ppb and long-term stability for a 30-day measurement. In addition, the response obtained for the CTAB-MoS2/rGO sensor was about two to four times that obtained for the MoS2/rGO sensor and the MoS2 sensor toward 8 ppm NO2, which correlated with the heterojunction between MoS2 and rGO, and the improvement in surface area and conductivity correlated with the introduction of CTAB and rGO. The excellent performance of the CTAB-MoS2/rGO sensor further suggested the advantage of CTAB in assisting a reliable detection of trace NO2 and an alternative method for highly efficiently detecting NO2 in the environment.

MoS2@ZnO Nanoheterostructures Prepared by Electrospark Erosion for Photocatalytic Applications

MoS₂@ZnO nanoheterostructures were synthesized by electrospark erosion of zinc granules in a hydrogen peroxide solution and simultaneous addition of MoS₂ nanostructured powder into the reaction zone. The morphology, size of the crystallites, as well as elemental and phase composition of the prepared structures, were examined using transmission electron microscopy and X-ray diffraction analysis. It was found that the synthesized products represent heterostructures containing MoS₂ nanoparticles formed on ZnO nanoparticles. Raman spectroscopy and photoluminescence analysis were also used for characterization of the prepared heterostructures. The obtained MoS₂@ZnO nanostructures revealed an intense broad emission band ranging from 425 to 625 nm for samples with different fractions of MoS₂. Photocatalytic measurements showed that the maximal hydrogen evolution rate of the prepared nanoheterostructures was about 906.6 μmol·g⁻¹·h⁻¹. The potential of their application in photocatalytic water splitting was also estimated.