Volatile Organic Compounds (VOCs) Removal from Indoor Air by Heterostructures/Composites/Doped Photocatalysts: A Mini-Review

Recent Developments in Photocatalytic Nanotechnology for Purifying Air Polluted with Volatile Organic Compounds: Effect of Operating Parameters and Catalyst Deactivation

Photocatalytic oxidation (PCO) is a successful method for indoor air purification, especially for removing low-concentration pollutants. Volatile organic compounds (VOCs) form a class of organic pollutants that are released into the atmosphere by consumer goods or via human activities. Once they enter the atmosphere, some might combine with other gases to create new air pollutants, which can have a detrimental effect on the health of living beings. This review focuses on current developments in the degradation of indoor pollutants, with an emphasis on two aspects of PCO: (i) influence of environmental (external) conditions; and (ii) catalyst deactivation and possible solutions. TiO2 is widely used as a photocatalyst in PCO because of its unique properties. Here, the potential effects of the operating parameters, such as the nature of the reactant, catalyst support, light intensity, and relative humidity, are extensively investigated. Then the developments and limitations of the PCO technique are highlighted, especially photocatalyst deactivation. Furthermore, the nature and deactivation mechanisms of photocatalysts are discussed, with possible solutions for reducing catalyst deactivation. Finally, the challenges and future directions of PCO technology for the elimination of indoor pollutants are compared and summarized.

Recent advances in the chemical oxidation of gaseous volatile organic compounds (VOCs) in liquid phase

The chemical oxidation of gaseous volatile organic compounds (VOCs) in liquid phase may possess great advantages in its high removal efficiency, mild conditions, good reliability, wide applicability, and little potential secondary pollution, which has aroused extensive research interests in the past decade. This Overview Article summarizes the latest achievements to eliminate VOCs by chemical oxidation in liquid phase including gas-liquid mass transfer, homogeneous/heterogeneous oxidation, electrochemical oxidation, and coupling technologies. Important research contributions are highlighted in terms of mass transfer, catalytic materials, removal/mineralization efficiency, and reaction mechanism to evaluate their potential industrial applications. The current challenges and future strategies are discussed from the viewpoint of the deep degradation of refractory VOC substrates and their intermediates. It is anticipated that this review will attract more attention toward the development and application of chemical oxidation methods to clear complex industrial organic exhaust gas.

Nano Metal-Containing Photocatalysts for the Removal of Volatile Organic Compounds: Doping, Performance, and Mechanisms

Volatile organic compounds (VOCs) in indoor air are considered a major threat to human health and environmental safety. The development of applicable technologies for the removal of VOCs is urgently needed. Nowadays, photocatalytic oxidation (PCO) based on metal-containing photocatalysts has been regarded as a promising method. However, unmodified photocatalysts are generally limited in applications because of the narrow light response range and high recombination rate of photo-generated carriers. As a result, nano metal-containing photocatalysts doped with elements or other materials have attracted much attention from researchers and has developed over the past few decades. In addition, different doping types cause different levels of catalyst performance, and the mechanism for performance improving is also different. However, there are few reviews focusing on this aspect, which is really important for catalyst design and application. This work aims to give a comprehensive overview of nano metal-containing photocatalysts with different doping types for the removal of VOCs in an indoor environment. First, the undoped photocatalysts and the basic mechanism of PCO is introduced. Then, the application of metal doping, non-metal doping, co-doping, and other material doping in synthetic metal-containing photocatalysts are discussed and compared, respectively, and the synthesis methods, removal efficiency, and mechanisms are further investigated. Finally, a development trend for using nano metal-containing photocatalysts for the removal of VOCs in the future is proposed. This work provides a meaningful reference for selecting effective strategies to develop novel photocatalysts for the removal of VOCs in the future.

Functional Microfiber Nonwoven Fabric with Copper Ion-Immobilized Polymer Brush for Detection and Adsorption of Acetone Gas

The detection and removal of volatile organic compounds (VOCs) are emerging as an important problem in modern society. In this study, we attempted to develop a new material capable of detecting or adsorbing VOCs by introducing a new functional group and immobilizing metal ions into a microfiber nonwoven fabric (MNWF) made through radiation-induced graft polymerization. The suitable metal complex was selected according to the data in “Cambridge Crystallographic Data Center (CCDC)”. 4-picolylamine (4-AMP), designated as a ligand through the metal complex data of CCDC, was introduced at an average mole conversion rate of 63%, and copper ions were immobilized at 0.51 mmol/g to the maximum. It was confirmed that degree of grafting (dg) 170% 4-AMP-Cu MNWF, where copper ions are immobilized, can adsorb up to 50% of acetone gas at about 50 ppm, 0.04 mmol/g- 4-AMP-Cu-MNWF, at room temperature and at a ratio of copper ion to adsorbed acetone of 1:10.

Copper Oxide-Based Photocatalysts and Photocathodes: Fundamentals and Recent Advances

This work aims at reviewing the most impactful results obtained on the development of Cu-based photocathodes. The need of a sustainable exploitation of renewable energy sources and the parallel request of reducing pollutant emissions in airborne streams and in waters call for new technologies based on the use of efficient, abundant, low-toxicity and low-cost materials. Photoelectrochemical devices that adopts abundant element-based photoelectrodes might respond to these requests being an enabling technology for the direct use of sunlight to the production of energy fuels form water electrolysis (H2) and CO2 reduction (to alcohols, light hydrocarbons), as well as for the degradation of pollutants. This review analyses the physical chemical properties of Cu2O (and CuO) and the possible strategies to tune them (doping, lattice strain). Combining Cu with other elements in multinary oxides or in composite photoelectrodes is also discussed in detail. Finally, a short overview on the possible applications of these materials is presented.

da Costa Filho B, Espíndola JC, Piazza D, J. P. Vilar V, A. Lansarin M. ZnO Polymeric Composite Films for n-Decane Removal from Air Streams in a Continuous Flow NETmix Photoreactor under UVA Light

Polymeric composite films have been explored for many photocatalytic applications, from water treatment to self-cleaning devices. Their properties, namely, thickness and porosity, are controlled mainly by the preparation conditions. However, little has been discussed on the effect of thickness and porosity of polymeric composite films for photocatalytic processes, especially in gas phase. In the present study, different preparation treatments of ZnO-based polymeric composite films and their effects on its performance and stability were investigated. The polymeric composites were prepared by solution mixing followed by non-solvent induced phase separation (NIPS), using poly(vinylidene fluoride) (PVDF) as the matrix and ZnO-based photocatalysts. Different wet thickness, photocatalyst mass, and treatments (e.g., using or not pore-forming agent and compatibilizer) were assessed. A low ZnO/PVDF ratio and higher wet thickness, together with the use of pore-forming agent and compatibilizer, proved to be a good strategy for increasing photocatalytic efficiency given the low agglomerate formation and high polymer transmittance. Nonetheless, the composites exhibited deactivation after several minutes of exposure. Characterization by XRD, FTIR-ATR, and SEM were carried out to further investigate the polymeric film treatments and stability. ZnO film was most likely deactivated due to zinc carbonate formation intensified by the polymer presence.