Decoration of SiO2 and Fe3O4 Nanoparticles onto the Surface of MWCNT-Grafted Glass Fibers: A Simple Approach for the Creation of Binary Nanoparticle Hierarchical and Multifunctional Composite Interphases

Bio-functionalized nickel-silica nanoparticles suppress bacterial leaf blight disease in rice (Oryza sativa L.)

Introduction

Bacterial leaf blight (BLB) caused by Xanthomonas oryzae pv. oryzae (Xoo) is one of the most devastative diseases that threatens rice plants worldwide. Biosynthesized nanoparticle (NP) composite compounds have attracted attention as environmentally safe materials that possess antibacterial activity that could be used in managing plant diseases.

Methods

During this study, a nanocomposite of two important elements, nickel and silicon, was biosynthesized using extraction of saffron stigmas (Crocus sativus L.). Characterization of obtained nickel-silicon dioxide (Ni-SiO2) nanocomposite was investigated using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Transmission/Scanning electron microscopy (TEM/SEM), and energy-dispersive spectrum (EDS). Antibacterial activities of the biosynthesized Ni-SiO2 nanocomposite against Xoo were tested by measuring bacterial growth, biofilm formation, and dead Xoo cells.

Results and discussions

The bacterial growth (OD600) and biofilm formation (OD570) of Xoo treated with distilled water (control) was found to be 1.21 and 1.11, respectively. Treatment with Ni-SiO2 NPs composite, respectively, reduced the growth and biofilm formation by 89.07% and 80.40% at 200 μg/ml. The impact of obtained Ni-SiO2 nanocomposite at a concentration of 200 μg/ml was assayed on infected rice plants. Treatment of rice seedlings with Ni-SiO2 NPs composite only had a plant height of 64.8 cm while seedlings treated with distilled water reached a height of 45.20 cm. Notably, Xoo-infected seedlings treated with Ni-SiO2 NPs composite had a plant height of 57.10 cm. Furthermore, Ni-SiO2 NPs composite sprayed on inoculated seedlings had a decrease in disease leaf area from 43.83% in non-treated infected seedlings to 13.06% in treated seedlings. The FTIR spectra of biosynthesized Ni-SiO2 nanocomposite using saffron stigma extract showed different bands at 3,406, 1,643, 1,103, 600, and 470 cm-1. No impurities were found in the synthesized composite. Spherically shaped NPs were observed by using TEM and SEM. EDS revealed that Ni-SiO2 nanoparticles (NPs) have 13.26% Ni, 29.62% Si, and 57.11% O. Xoo treated with 200 µg/ml of Ni-SiO2 NPs composite drastically increased the apoptosis of bacterial cells to 99.61% in comparison with 2.23% recorded for the control.

Conclusions

The application of Ni-SiO2 NPs significantly improved the vitality of rice plants and reduced the severity of BLB.

Synthesis and characterization of silica nanoparticles from rice ashes coated with chitosan/cancer cell membrane for hepatocellular cancer treatment

Dual pH-sensitive smart nanocarriers based on silica nanoparticles (SNPs) extracted from rice husk ashes (RHAs) to effectively inhibit liver cancer cell proliferation were investigated. The SNPs were coated with chitosan (CH) and loaded with doxorubicin (DOX), then functionalized with cell membrane (CM) for homologous targeting ability. The FTIR spectra showed an absorption wave number at 1083 cm^-1 which confirmed the existence of the SiOSi group, ratifying that the nanocarriers belong to silica species. The Korsmeyer-Peppas kinetic model reported R² values of 0.996 and 0.931 for pH = 5.4 and pH = 7.4, respectively, demonstrating pH-responsive behavior of the nanocarriers. The cytotoxicity test confirmed that the HepG2 cell line treated with different SNP-CH-CM concentrations had no detectable significant cell toxicity, however, SNP-CH-DOX-CM induced greater cell death. In vivo tests revealed that SNP-CH-DOX-CM suppressed liver cancer growth in nude mice, demonstrating high pharmaceutical capability. Histological examination of vital organs showed that the targeted drug delivery system (DDS) had minor in vivo toxicity. In the light of its high treatment efficacy and minimal side effects, the investigated DDS is promising for the therapy of liver cancer.

High-Performance Dental Composites Based on Hierarchical Reinforcements

Use of high-performance fibers such as poly(p-phenylene-2,6-benzobisoxazole) (PBO) improves the mechanical properties of dental fiber-reinforced composites (FRCs). However, the surfaces of high-performance fibers are relatively inert, and the interface with the resin matrix is poor. This has become a limitation restricting the performance of PBO FRCs in dentistry. Nanomaterials were introduced onto PBO fibers to construct various hierarchical reinforcements to obtain a dental FRC with higher flexural performance and optimized interface bonding. Four hierarchical reinforcements were constructed: PBO-ZnO nanoparticles (NPs), PBO-ZnO nanowires (NWs), PBO-ZnO NPs–cage silsesquioxane (POSS), and PBO-ZnO NWs-POSS. Performance following this optimized method was evaluated at macroscale and microscale levels, including measurement of the interfacial properties and mechanical properties of FRCs. The physicochemical characteristics of PBO fibers before and after modification were measured to determine the interfacial bonding mechanisms and to verify the connection between the microinterface and macromechanical properties. The cytotoxicity of the preferred PBO FRC was evaluated using the CCK8 assay. In comparison to other designs, the interfacial shear strength (IFSS) of PBO-ZnO NWs-POSS was the highest (29.31 ± 2.40 MPa). The corresponding FRC had the highest flexural strength under a static load (925.0 ± 39.2 MPa), the flexural modulus (39.39 ± 1.41 GPa) was equivalent to that of human dentin, and in vitro cytotoxicity was acceptable. The interfacial bonding mechanisms of PBO-ZnO NWs-POSS resulted from mechanical interlocking, chemical bonds, hydrogen bonds, and van der Waals forces. In summary, the PBO-ZnO NWs-POSS hierarchical reinforcement was introduced in dental FRCs and showed remarkable enhancement of the IFSS and flexural properties. We verified that the PBO-ZnO NWs-POSS hierarchical reinforcement was successful. This PBO FRC may be applied in dentistry as a new option for endodontic posts. Our study provides an interface design strategy for developing high-performance FRCs reinforced with high-performance fibers for dental applications.

A Review on Synthesis, Properties, and Applications of Polylactic Acid/Silica Composites

Polylactic acid (PLA)/silica composites as multifunctional high-performance materials have been extensively examined in the past few years by virtue of their outstanding properties relative to neat PLA. The fabrication methods, such as melt-mixing, sol–gel, and in situ polymerization, as well as the surface functionalization of silica, used to improve the dispersion of silica in the polymer matrix are outlined. The rheological, thermal, mechanical, and biodegradation properties of PLA/silica nanocomposites are highlighted. The potential applications arising from the addition of silica nanoparticles into the PLA matrix are also described. Finally, we believe that a better understanding of the role of silica additive with current improvement strategies in the dispersion of this additive in the polymer matrix is the key for successful utilization of PLA/silica nanocomposites and to maximize their fit with industrial applications needs.

Enhanced Mechanical, Thermal and Antimicrobial Properties of Additively Manufactured Polylactic Acid with Optimized Nano Silica Content

The scope of this work was to create, with melt mixing compounding process, novel nanocomposite filaments with enhanced properties that industry can benefit from, using commercially available materials, to enhance the performance of three-dimensional (3D) printed structures fabricated via fused filament fabrication (FFF) process. Silicon Dioxide (SiO₂) nanoparticles (NPs) were selected as fillers for a polylactic acid (PLA) thermoplastic matrix at various weight % (wt.%) concentrations, namely, 0.5, 1.0, 2.0 and 4.0 wt.%. Tensile, flexural and impact test specimens were 3D printed and tested according to international standards and their Vickers microhardness was also examined. It was proven that SiO₂ filler enhanced the overall strength at concentrations up to 1 wt.%, compared to pure PLA. Atomic force microscopy (AFM) was employed to investigate the produced nanocomposite extruded filaments roughness. Raman spectroscopy was performed for the 3D printed nanocomposites to verify the polymer nanocomposite structure, while thermogravimetric analysis (TGA) revealed the 3D printed samples' thermal stability. Scanning electron microscopy (SEM) was carried out for the interlayer fusion and fractography morphological characterization of the specimens. Finally, the antibacterial properties of the produced nanocomposites were investigated with a screening process, to evaluate their performance against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus).