Interfacial Strengthening of Graphene/Aluminum Composites through Point Defects: A First-Principles Study

Electro-optical properties of strained monolayer boron phosphide

In this paper, we use tight-binding approximation and linear response theory to study the electronic and optical properties of strained monolayer boron-phosphide (h-BP). Compared with the previous DFT study and adding on-site energy variation to the Hamiltonian, we propose a theoretical approach to investigate the strain effects on the electronic and optical properties of the h-BP. Applying tensile strain increases the gap while compressive strain reduces it as the maximum and minimum of the gap are 1.45 eV and 1.14 eV respectively and are related to the biaxial strain. Also, we investigate the optical conductivity and electron energy loss spectrum (EELS) of the pristine and strained h-BP. The absorption peak of the [Formula: see text] appears in energy about 4 eV but applying strain shifts the peak's energy. Optical properties of pristine h-BP are isotopic and biaxial strain preserves this isotropy, but uniaxial strain exerts anisotropic behavior in the system.

Extended Line Defect Graphene Modified by the Adsorption of Mn Atoms and Its Properties of Adsorbing CH4

Extended line defect (ELD) graphene is a two-dimensional (2D) topologically defective graphene with alternate octagonal and quadrilateral carbon rings as basic defective units. This paper reports on the CH4 adsorption properties of ELD graphene according to the first principles of density functional theory (DFT). The effects on the CH4 adsorption of ELD graphene when modified by a single Mn atom or two Mn atoms were investigated, respectively. An ELD-42C graphene configuration consisting of 42 C atoms was first constructed. Then, the ELD-42C graphene configuration was used as a substrate, and a Mn-ELD-42C graphene configuration was obtained by modifying it with a single Mn atom. The results showed that the most stable adsorption site for Mn atoms was above the quadrilateral carbon ring. This Mn-ELD-42C graphene configuration could only stably adsorb up to 30 CH4 molecules on each side, with an average adsorption energy of −0.867 eV/CH4 and an adsorption capacity of 46.25 wt%. Three 2Mn-ELD-42C graphene configurations were then obtained by modifying the ELD-42C graphene substrate with two Mn atoms. When the two Mn atoms were located on either side of a 2Mn-ELD-42C graphene configuration and above the two octagonal carbon rings adjacent to the same quadrilateral carbon ring, it was able to adsorb up to 40 CH4 molecules on each side, with an average adsorption energy of −0.862 eV/CH4 and a CH4 adsorption capacity of 51.09 wt%.

Corrosion Resistance of Ultrathin Two-Dimensional Coatings: First-Principles Calculations towards In-Depth Mechanism Understanding and Precise Material Design

In recent years, ultrathin two-dimensional (2D) coatings, e.g., graphene (Gr) and hexagonal boron nitride (h-BN), are intriguing research foci in the field of anticorrosion because their high air stability, excellent impermeability, high optical transparency, and atomistic thickness have endowed them with attractive anticorrosion applications. The microstructure of 2D coatings, coating–substrate interactions, and properties of 2D coatings on substrates in a variety of environmental conditions (e.g., at different temperatures, stresses, and pH values) are the key factors governing the anticorrosion performance of 2D coatings and are among the central topics for all 2D-coating studies. For many conventional experimental measurements (e.g., microscopy and electrochemical methods), there exist challenges to acquire detailed information on the atomistic mechanisms for the involved subnanometer scale corrosion problems. Alternatively, as a precise and efficient quantum-mechanical simulation approach, the first-principles calculation based on density-functional theory (DFT) has become a powerful way to study the thermodynamic and kinetic properties of materials on the atomic scale, as well as to clearly reveal the underlying microscopic mechanisms. In this review, we introduce the anticorrosion performance, existing problems, and optimization ways of Gr and h-BN coatings and summarize important recent DFT results on the critical and complex roles of coating defects and coating–substrate interfaces in governing their corrosion resistance. These DFT progresses have shed much light on the optimization ways towards better anticorrosion 2D coatings and also guided us to make a prospect on the further development directions and promising design schemes for superior anticorrosion ultrathin 2D coatings in the future.

Defects and Strain Engineering of Structural, Elastic, and Electronic Properties of Boron-Phosphide Monolayer: A Hybrid Density Functional Theory Study

Defects and in-plane strain have significant effects on the electronic properties of two-dimensional nanostructures. However, due to the influence of substrate and environmental conditions, defects and strain are inevitable during the growth or processing. In this study, hybrid density functional theory was employed to systematically investigate the electronic properties of boron-phosphide monolayers tuned by the in-plane biaxial strain and defects. Four types of defects were considered: B-vacancy (B_v), P-vacancy (P_v), double vacancy (D_v), and Stone–Wales (S-W). Charge density difference and Bader charge analysis were performed to characterize the structural properties of defective monolayers. All of these defects could result in the boron-phosphide monolayer being much softer with anisotropic in-plane Young’s modulus, which is different from the isotropic modulus of the pure layer. The calculated electronic structures show that the P_v, D_v, and S-W defective monolayers are indirect band gap semiconductors, while the B_v defective system is metallic, which is different from the direct band gap of the pure boron-phosphide monolayer. In addition, the in-plane biaxial strain can monotonically tune the band gap of the boron-phosphide monolayer. The band gap increases with the increasing tension strain, while it decreases as the compression strain increases. Our results suggest that the defects and in-plane strain are effective for tuning the electronic properties of the boron-phosphide monolayer, which could motivate further studies to exploit the promising application in electronics and optoelectronics based on the boron-phosphide monolayer.