Efficient and Rapid Photocatalytic Degradation of Methyl Orange Dye Using Al/ZnO Nanoparticles

An Efficient p-n Heterojunction Copper Tin Sulfide/g-C3N4 Nanocomposite for Methyl Orange Photodegradation

The discharge of toxic dye effluents from industry is a major concern for environmental pollution and toxicity. These toxic dyes can be efficiently removed from waste streams using a photocatalysis process involving visible light. Due to its simple synthesis procedure, inexpensive precursor, and robust stability, graphitic carbon nitride (g-C3N4, or CN) has been used as a visible light responsive catalyst for the degradation of dyes with mediocre performance because it is limited by its low visible light harvesting capability due to its wide bandgap and fast carrier recombination rate. To overcome these limitations and enhance the performance of g-C3N4, it was coupled with a narrow bandgap copper tin sulfide (CTS) semiconductor to form a p-n heterojunction. CTS and g-C3N4 were selected due to their good stability, low toxicity, ease of synthesis, layered sheet/plate-like morphology, and relatively abundant precursors. Accordingly, a series of copper tin sulfide/graphitic carbon nitride nanocomposites (CTS/g-C3N4) with varying CTS contents were successfully synthesized via a simple two-step process involving thermal pyrolysis and coprecipitation for visible-light-induced photocatalytic degradation of methyl orange (MO) dye. The photocatalytic activity results showed that the 50%(wt/wt) CTS/g-C3N4 composite displayed a remarkable degradation efficiency of 95.6% for MO dye under visible light illumination for 120 min, which is higher than that of either pristine CTS or g-C3N4. The improved performance is attributed to the extended light absorption range (due to the optimized bandgap), effective suppression of photoinduced electron-hole recombination, and improved charge transfer that arose from the formation of a p-n heterojunction, as evidenced by electrochemical impedance spectroscopy (EIS), photocurrent, and photoluminescence results. Moreover, the results of the reusability study showed that the composite has excellent stability, indicating its potential for the degradation of MO and other toxic organic dyes from waste streams.

Study on Preparation of Calcium-Based Modified Coal Gangue and Its Adsorption Dye Characteristics

Efficient and thorough treatment of dye wastewater is essential to achieve ecological harmony. In this study, a new type of calcium-based modified coal gangue (Ca-CG) was prepared by using solid waste coal gangue as raw material and a CaCl2 modifier, which was used for the removal of malachite green, methylene blue, crystal violet, methyl violet and other dyes in water. When the dosage of Ca-CG was 1-5 g/L, the dosage of Ca-CG was the main factor affecting the dye adsorption effect. The adsorption effects of Ca-CG on four dyes were as follows: malachite green > crystal violet > methylene blue > methyl violet. Kinetics, isotherms and thermodynamic analysis showed that the adsorption of malachite green, methyl blue, crystal violet and methyl violet by Ca-CG fitted the second-order kinetic model, and adsorption with chemical reaction is the main process. The adsorption of four dyes by Ca-CG conformed to the Freundlich model, which is dominated by multi-molecular layer adsorption, and the adsorption was easy to carry out. The adsorption process of Ca-CG on the four dyes was spontaneous. The results of FTIR, XRD and SEM showed that the calcium-based materials such as lipscombite and dolomite were the key to the adsorption of malachite green by Ca-CG, and the main mechanisms for the adsorption of malachite green by Ca-CG are surface precipitation, electrostatic action, and chelation reaction. Ca-CG adsorption has great potential for the removal of dye wastewater.

Zeolite 13X incorporated with Zn-Ce oxide nanocatalyst for removal of Reactive Red 120 dye: RSM-based approach

In this study, the photocatalytic removal of Reactive Red 120 (RR120) dye was examined using zeolite 13X incorporated with Zn-Ce under UV irradiation. The synthesis of Zn-Ce nanoparticles incorporated with zeolite 13X was conducted through the co-precipitation method, and the features of the prepared nanocatalyst were analyzed using various techniques. The SEM and BET analyses indicated successful incorporation of ZnO-Ce oxides on the surface of zeolite 13X and a specific surface area of 359.39 m2/gm, respectively. Further, the average size of crystal grains was 28 nm. The response surface methodology (RSM) approach was employed to optimize operating parameters. The quadratic model suggested by the RSM approach, characterized by a high regression coefficient (R2 = 0.9632), indicates a high level of reliability. Moreover, under optimal conditions (catalyst loading of 4 mg, pH of 3, H2O2 amount of 0.2 mL, UV power of 25 W, and reaction time of 60 min), the highest RR120 dye removal percentage was 99.97%. Kinetic data indicated an increase in the reaction rate constant from 0.0631 to 0.1796 min-1. The zeolite 13X incorporated with Zn-Ce photocatalyst exhibited excellent stability over 5 cycles, with only a 5.50% decrease in RR120 dye removal yield. This study demonstrates the promising potential of zeolite 13X incorporated with Zn-Ce nanoparticles for the removal of RR120 dye from aqueous suspension.

Synthesis and application of novel microporous framework of nanocomposite from trona for photocatalysed degradation of methyl orange dye

Photocatalysed degradation of environmental contaminants is one of the most fashionable technologies in the purification of water because the method converts toxic products to nontoxic ones. In this study, a method has been developed to synthesize novel nanocomposites of Na-Ca-Al-Si oxides for the first time. The average surface area, pore volume and pore size for the novel product were 1742.55 m2/g, 0.3499 cc/g and 3.197 nm respectively. The crystal parameters were a = 7.1580 Å, b = 7.4520 Å, c = 7.7160 Å, α = 115.0600, β = 107.3220, γ = 100.4380, density (calculated) = 2.0 × 103g/cm3 and cell volume = 332.7 Å3 respectively. The average crystalline size deduced from the Scherrer equation (i.e. 6.9393 nm) was higher than the value of 1.024 nm obtained from the graphical method. The FTIR and UV spectra of the nanocomposites were unique and provided baseline information that characterises the new product. XRD profiling of the new product reveals the existent of a silica framework consisting of NaAlSi3O3 and CaAl2Si2O8 The synthesized nanocomposites is an effective photocatalyst for the degradation of methyl orange dye in water, with aoptimum efficiency of 96% at an initial dye concentration of 10 ppm, the adsorbent dosage of 0.5 g,contact time of 90 min and pH of 2.5. The Langmuir-Hinshelwood, modified Freundlich and pseudo-second kinetic models were significant in the description of the photocatalytic kinetics of the degraded dye molecules.

Enhanced photocatalytic performance of milkvetch-derived biochar via ZnO-Ce nanoparticle decoration for reactive blue 19 dye removal

In this research, the photocatalytic removal of reactive blue 19 (RB19) dye is investigated employing zinc oxide/cerium (ZnO@Ce) nanoparticles decorated with biochar under LED irradiation. Synthesis of ZnO@Ce nanoparticles decorated with biochar was performed utilizing the co-precipitation procedure and, then, the texture and morphology of the fabricated nanocomposite were analyzed using energy dispersive X-ray (EDX), field emission scanning electron microscopy (FE-SEM), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), and Fourier transform infrared (FTIR) spectroscopy techniques. Moreover, FE-SEM images demonstrate that ZnO-Ce nanoparticles were successfully decorated on the surface of biochar. The specific surface areas of biochar and biochar/ZnO-Ce were 519.75 and 636.52 m2/g, respectively. To achieve the maximum yield in the removal of RB19 dye, the effects of operating variables including dye concentration, LED lamp power, biochar@ZnO-Ce catalyst dose, pH and H2O2 dose were explored. Besides, the maximum percentage of RB19 dye removal was 96.47% under optimal conditions, i.e. catalyst dosage of 100 mg, H2O2 dosage of 1 mL, pH of 9, initial dye concentration of 5 ppm, LED power of 50 W, and reaction time of 140 min. Furthermore, the kinetic analysis reveals that the removal of RB19 dye follows the pseudo-first order kinetic model, with calculated values of a reaction rate constant of 0.045 min-1 and a correlation coefficient of R2 = 0.99, respectively. Moreover, the reusability and recyclability of biochar@ZnO/Ce nanocatalyst was promising over five runs, with only a 6.08% decrease in RB19 dye removal efficiency. Therefore, it can be concluded that the biochar @ZnO/Ce photocatalyst can be promisingly applied for the removal of azo dyes in aqueous solutions.

Dual functional WO3/BiVO4 heterostructures for efficient photoelectrochemical water splitting and glycerol degradation

Dual functional heterojunctions of tungsten oxide and bismuth vanadate (WO₃/BiVO₄) photoanodes are developed and their applications in photoelectrochemical (PEC) water splitting and mineralization of glycerol are demonstrated. The thin-film WO₃/BiVO₄ photoelectrode was fabricated by a facile hydrothermal method. The morphology, chemical composition, crystalline structure, chemical state, and optical absorption properties of the WO₃/BiVO₄ photoelectrodes were characterized systematically. The WO₃/BiVO₄ photoelectrode exhibits a good distribution of elements and a well-crystalline monoclinic WO₃ and monoclinic scheelite BiVO₄. The light-absorption spectrum of the WO₃/BiVO₄ photoelectrodes reveals a broad absorption band in the visible light region with a maximum absorption of around 520 nm. The dual functional WO₃/BiVO₄ photoelectrodes achieved a high photocurrent density of 6.85 mA cm^-2, which is 2.8 times higher than that of the pristine WO₃ photoelectrode in the presence of a mixture of 0.5 M Na₂SO₄ and 0.5 M glycerol electrolyte under AM 1.5 G (100 mW cm^-2) illumination. The superior PEC performance of the WO₃/BiVO₄ photoelectrode was attributed to the synergistic effects of the superior crystal structure, light absorption, and efficient charge separation. Simultaneously, glycerol plays an essential role in increasing the efficiency of hydrogen production by suppressing charge recombination in the water redox reaction. Moreover, the WO₃/BiVO₄ photoelectrode shows the total organic carbon (TOC) removal efficiency of glycerol at about 82% at 120 min. Notably, the WO₃/BiVO₄ photoelectrode can be a promising photoelectrode for simultaneous hydrogen production and mineralization of glycerol with a simple, economical, and environmentally friendly approach.

Efficient photodegradation of methyl red dye by kaolin clay supported zinc oxide nanoparticles with their antibacterial and antioxidant activities

Kaolin clay-supported Zinc oxide (ZnO/KC) and ZnO NPs nanoparticles (NPs) were prepared by a chemical reduction process and used for the photodegradation of methyl red (MR) dye as a photocatalyst. Due to the interlayered porous structure of the KC, we achieved an extremely good association between ZnO NPs and KC. The product confirmation was conducted by Scanning electron microscopy (SEM), X-Ray diffraction (XRD), energy dispersive X-Ray (EDX), and Fourier transforms infrared (FTIR). SEM showed the irregular morphology of ZnO NPs, while ZnO/KC NCs were predominately round-shaped. Moreover, in both cases, NPs were present in both dispersed as well as agglomerated forms with an average particle size below 100 nm. The results acquired from photodegradation analyses show that ZnO NPs and ZnO/KC NCs degraded about 90 and 99% of MR dye respectively, under UV light in a short irradiation time of 10 min. The recovered and re-recovered ZnO NPs and ZnO/KC NCs also considerably photodegraded MR dye in an aqueous medium. The same NPs also exhibit promising bioactivities against two pathogenic bacteria, i.e., Citrobacter and Providencia. The antioxidant activity of ZnO/KC NCs reached to reasonable 70% compared to the 88% activity of the standard ascorbic acid.

A Study on Doping and Compound of Zinc Oxide Photocatalysts

As an excellent semiconductor photocatalyst, zinc oxide is widely used in the field of photocatalysis and is regarded as one of the most reliable materials to solve environmental problems. However, because its band gap energy limits the absorption of visible light and reduces the efficiency of catalytic degradation, it needs to be doped with other substances or compounded with other substances and precious metal. This paper summarizes the research on this aspect at home and abroad in recent years, introduces the doping of transition metal ions by zinc oxide, the compounding of zinc oxide with precious metals or other semiconductors, and the prospect of further improving the catalytic efficiency of zno photocatalyst is also put forward.

Degradation of dyes by UV/Persulfate and comparison with other UV-based advanced oxidation processes: Kinetics and role of radicals

This study investigated the degradation of methylene blue (MeB), methyl orange (MeO), and rhodamin B (RhB) by the UV/Persulfate (UV/PS) process. The dye degradation in the investigated UV-based Advanced Oxidation Processes (UV/AOPs) followed the first-order kinetic model. The second-order rate constant of the dyes with •OH, SO₄^•-, and CO₃^•- were calculated and found to be: k_•OH,MeB = 5.6 × 10⁹ M^-1 s^-1, [Formula: see text]  = 3.3 × 10⁹ M^-1 s^-1, [Formula: see text]  = 6.9 × 10⁷ M^-1 s^-1; k_•OH,MeO = 3.2 × 10⁹ M^-1 s^-1, [Formula: see text]  = 13 × 10⁹ M^-1 s^-1, [Formula: see text]  = 4.4 × 10⁶ M^-1 s^-1; k_•OH,RhB = 14.8 × 10⁹ M^-1 s^-1, [Formula: see text]  = 5 × 10⁹ M^-1 s^-1, [Formula: see text]  = 1 × 10⁷ M^-1 s^-1. The steady-state concentrations of •OH and SO₄^•- (including other reactive species) were determined using both chemical probes and modeling methods (Kintecus® V6.8). In the UV/PS, the dye degradation depends on the pH of the solution with the order: k_dye (at pH of 7) > k_dye (in acidic conditions) > k_dye (in alkaline conditions). The presence of water matrices had different impacts on dye degradation: 1) The HCO₃^- and Cl^- promoted the degradation efficiency of one dye, but also inhibited the degradation of other dyes; 2) Humic acid (HA) inhibited dye degradation as it scavenged both •OH and SO₄^•-. The degradation of the dyes by UV/PS was also compared with the UV/Chlorine (UV/HOCl) and UV/H₂O₂ and it was established that: 1) In UV/PS and UV/HOCl, SO₄^•- and RCS contributed to dye degradation more than •OH, while •OH played a major role in dye degradation by UV/H₂O₂; 2) The calculated toxicity in UV/PS was the lowest probably due to the low toxicity of by-products; 3) For MeO and RhB, the UV/PS process is more beneficial for the total organic carbon (TOC) removal compared to that of the UV/HOCl and UV/H₂O₂ processes; 4) The UV/PS showed lower cost than the UV/HOCl and UV/H₂O₂ systems for MeO, and RhB degradation but higher cost for MeB removal.

Photocatalytic Degradation of Phenol Red in Water on Nb(x)/TiO2 Nanocomposites

In this paper, the photocatalytic effect of Nb(x)/TiO2 nanocomposites on the degradation of phenol red (PR) was studied. Nb(x)/TiO2 nanocomposites are fabricated by a simple sol-gel route with new experimental conditions. The structural and optical properties were determined using high transmission electron microscopy (HRTEM), X-ray diffraction, Raman spectroscopy, photoluminescence, and UV-vis absorbance spectroscopy. Compared to pure anatase TiO2, the recently fabricated Nb(x)/TiO2 nanocomposite has a shift in the optical band edge to the visible wavelength. Consequently, it has high performance in adsorption capacity and photocatalytic activities. A time of 160 min has been observed to be suitable for mostly degradable 20 mgL−1 of phenol red on Nb(2.0)/TiO2 composite. The kinetic results were in good agreement with the first-order kinetic model at different concentrations. In addition, the results showed that the addition of Nb led to a significant degradation process. The decomposition of phenol red pollutants showed a synergistic effect of the Nb(2.0)/TiO2 nanocomposites on wastewater treatment.

Enhanced Photocatalytic Activity and Photoluminescence of ZnO Nano-Wires Coupled with Aluminum Nanostructures

In this study, we fabricated a hybrid plasmonic/semiconductor material by combining the chemical bath deposition of zinc oxide nanowires (ZnONWs) with the physical vapor deposition of aluminum nanostructures (AlNSs) under controlled temperature and atmosphere. The morphological and the optical properties of the ZnONWs/AlNSs hybrid material fabricated at different temperatures (250, 350, and 450 °C) and thicknesses (5, 7, and 9 nm) of Al layers were investigated. By adjusting the deposition and annealing parameters, it was possible to tune the size distribution of the AlNSs. The resonant coupling between the plasmonic AlNSs and ZnONWs leads to an enhanced photoluminescence response. The photocatalytic activity was studied through photodegradation under UV-light irradiation of methylene blue (MB) adsorbed at the surface of ZnO. The MB photodegradation experiment reveals that the ZnONWs covered with 7 nm aluminum film and annealed at 450 °C exhibit the highest degradation efficiency. The comparison between ZnONws and ZnONws/AlNSs shows a photoluminescence enhancement factor of 1.7 and an increase in the kinetics constant of photodegradation with a factor of 4.

Enhanced photocatalytic activities of a hierarchical ZnO/V2C MXene hybrid with a close coupling heterojunction for the degradation of methyl orange, phenol and methylene blue dye

A hierarchical ZnO/V2C MXene hybrid exhibited enhanced photocatalytic performance due to its close coupling heterojunction facilitating photo-generated carrier transfer.

The Phase Evolution and Photocatalytic Properties of a Ti-TiO2 Bilayer Thin Film Prepared Using Thermal Oxidation

Ti-TiO2 bilayer thin films were successfully prepared onto a glass substrate using magnetron sputtering with different TiO2 bottom layer conditions. These represent a lack of (as-deposited) and full oxygen content (annealed). Single-layer Ti was additionally used as a control. The influence of oxygen diffusion phenomena of the bottom layer of TiO2 to the upper layer of Ti thin films at different oxidation temperatures on structural, optical, and photocatalytic performance was investigated. X-ray diffraction (XRD) results confirmed that the crystalline phases coexisting on thin-film samples oxidized at 450 °C were TiO, TiO1.4, (bilayer, as-deposited TiO2), anatase (bilayer, annealed TiO2), and rutile (single and bilayer). This finding showed that the film’s phase structure evolution is significantly affected by oxygen diffusion from the bottom layer. Further increasing the thermal oxidation temperature caused a notable decline in the amorphous zone in bilayer thin films based on TEM analysis. Bilayer thin films lead to higher degradation of methylene blue under UV light radiation (63%) than single-layer films (45%) oxidized at 450 °C. High photocatalytic activity performance was found in the bilayer annealed TiO2-Ti thin-film sample. This study demonstrates that the bilayer modification strategy promotes the oxygen-induced bottom layer of TiO2 bilayer thin films.