Mechanochemistry as an Alternative Method of Green Synthesis of Silver Nanoparticles with Antibacterial Activity: A Comparative Study

Mechanochemical hydroquinone regeneration promotes gold salt reduction in sub-stoichiometric conditions of the reducing agent

Bottom-up mechanochemical synthesis (BUMS) has been demonstrated to be an efficient approach for the preparation of metal nanoparticles (NPs), protected by surface agents or anchored on solid supports. However, there are limitations, such as precise size and morphological control, due to a lack of knowledge about the mechanically induced processes of NP formation under milling. In this article, we further investigate the BUMS of AuNPs. Using SiO2 as a solid support, we studied the effect of typical reducing agents, namely NaBH4, L-ascorbic acid, and hydroquinone (HQ), on the conversion of a AuIII source. XANES showed that HQ is the strongest reducing agent under our experimental conditions, leading to the quantitative conversion of gold salt in a few minutes. Interestingly, even when HQ was used in sub-stoichiometric amounts, AuIII could be reduced to ratios higher than 85% after two minutes of milling. Investigations into the byproducts by 1H NMR and GC-FID/MS enabled the identification HQ regeneration and the formation of its derivatives. We mainly focused on benzoquinone (BQ), which is the product of the oxidation of HQ as it reduces the gold salt. We could demonstrate that HQ is regenerated from BQ exclusively under milling and acidic conditions. The regenerated HQ and other HQ-chlorinated molecules could then reduce gold-oxidized species, leading to higher conversions and economy of reactants. Our study highlights the intriguing and complex mechanisms of mechanochemical systems, in addition to fostering the atom and energy economy side of mechanochemical means to produce metal nanoparticles.

In-Vivo Bactericidal Potential of Mangifera indica Mediated Silver Nanoparticles against Aeromonas hydrophila in Cirrhinus mrigala

The present study reports the green synthesis of silver nanoparticles from leaves' extract of Mangifera indica (M. indica) and their antibacterial efficacy against Aeromonas hydrophila (A. hydrophila) in Cirrhinus mrigala (C. mrigala). The prepared M. indica mediated silver nanoparticles (Mi-AgNPs) were found to be polycrystalline in nature, spherical in shapes with average size of 62 ± 13 nm. C. mrigala (n = ±15/group) were divided into six groups i.e., G1: control, G2: A. hydrophila challenged, G3: A. hydrophila challenged + Mi-AgNPs (0.01 mg/L), G4: A. hydrophila challenged + Mi-AgNPs (0.05 mg/L), G5: A. hydrophila challenged + Mi-AgNPs (0.1 mg/L) and G6: A. hydrophila challenged + M. indica extract (0.1 mg/L). Serum biochemical, hematological, histological and oxidative biomarkers were evaluated after 15 days of treatment. The liver enzyme activities, serum proteins, hematological parameters and oxidative stress markers were found to be altered in the challenged fish but showed retrieval effects with Mi-AgNPs treatment. The histological analysis of liver, gills and kidney of the challenged fish also showed regaining effects following Mi-AgNPs treatment. A CFU assay from muscle tissue provided quantitative data that Mi-AgNPs can hinder the bacterial proliferation in challenged fish. The findings of this work suggest that M. indica based silver nanoparticles can be promising candidates for the control and treatment of microbial infections in aquaculture.

Editorial for the Special Issue "Biological and Toxicological Studies of Nanoparticles"

Nanoparticles have attracted a great deal of attention over the past two decades or more due to their unique size-dependent physical and chemical properties [...].

Antibacterial activity, quality and stability study of creams with new potential silver(I) complexes and in vivo case report

The aim of this study was to evaluate the antibacterial activity, quality and stability of creams (at 1 % concentration) prepared with synthesized silver(I) complexes: [Ag(Nam)₂]NO₃·H₂O ( AgNam), [Ag₂(HGly)₂]_n(NO₃)_2n (AgGly) (Nam - nicotin-amide, Gly - glycine) and silver(I) sulfadiazine (AgSD), which is commercially available. Antibacterial activity was evaluated by agar well diffusion method and in in vivo case. The pure silver(I) complexes as well as all three tested creams loaded with AgGly, AgSD and AgNam showed antibacterial potential. Moreover, the creams loaded with AgGly and AgNam showed higher antibacterial effects against S. aureus and B. subtilis than the cream loaded with AgSD. In terms of appearance, all cream samples were opaque and odourless, and no phase separation was observed. Creams were soluble in water (o/w emulsions) and they had a pseudoplastic behaviour. The pH of the creams was in the range of 4.87-5.75. No visible changes were observed in the case of commercially used AgSD cream during one month testing period at conditions -16 ± 1 °C; 6 ± 1 °C and 56 % relative humidity; 20 ± 1 °C and 58 % relative humidity and 40 ± 1 °C and 75 % relative humidity. However, creams containing AgGly and AgNam changed their colour depending on the tested conditions.

Transfer of AgNPs' Anti-Biofilm Activity into the Nontoxic Polymer Matrix

A biological method was successfully applied to synthesize spherical silver nanoparticles (AgNPs) while using the extract of lavender (Ex-L) (lat. Lavandula angustifolia) as the reducing and stabilizing agent. The produced nanoparticles were spherical with an average size of 20 nm. The AgNPs' synthesis rate confirmed the extract's excellent ability to reduce silver nanoparticles from the AgNO₃ solution. The presence of good stabilizing agents was confirmed by the excellent stability of the extract. Nanoparticles' shapes and sizes did not change. UV-Vis absorption spectrometry, Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) were used to characterize the silver nanoparticles. The silver nanoparticles were incorporated into the PVA polymer matrix by the "ex situ" method. The polymer matrix composite with AgNPs was prepared in two ways: as a composite film and nanofibers (nonwoven textile). The anti-biofilm activity of AgNPs and the ability of AgNPs to transfer toxic properties into the polymer matrix were proved.

Combining the Potent Reducing Properties of Pecan Nutshell with a Solvent-Free Mechanochemical Approach for Synthesizing High Ag0 Content-Silver Nanoparticles: An Eco-Friendly Route to an Efficient Multifunctional Photocatalytic, Antibacterial, and Antioxidant Material

A straightforward, low-cost, and scalable solid-state mechanochemical protocol for the synthesis of silver nanoparticles (AgNP) based on the use of the highly reducing agri-food by-product pecan nutshell (PNS) is reported herein. Under optimized conditions (180 min, 800 rpm, PNS/AgNO₃ ratio = 55/45 w/w), a complete reduction in silver ions was achieved, leading to a material containing ca. 36% w/w Ag⁰ (X-ray diffraction analysis). Dynamic light scattering and microscopic analysis showed a uniform size distribution (15-35 nm average diameter) of the spherical AgNP. The 2,2-Diphenyl-1-picrylhydrazyl (DPPH) assay revealed lower-although still absolutely high (EC₅₀ = 5.8 ± 0.5 mg/mL)-antioxidant properties for PNS for the further incorporation of AgNP, supporting the efficient reduction of Ag⁺ ions by PNS phenolic compounds. Photocatalytic experiments indicated that AgNP-PNS (0.4 mg/mL) was able to induce the >90% degradation of methylene blue after 120 min visible light irradiation, with good recycling stability. Finally, AgNP-PNS demonstrated high biocompatibility and significantly light-enhanced growth inhibition properties against Pseudomonas aeruginosa and Streptococcus mutans at concentrations as low as 250 μg/mL, also eliciting an antibiofilm effect at 1000 μg/mL. Overall, the adopted approach allowed to reuse a cheap and abundant agri-food by-product and required no toxic or noxious chemicals, making AgNP-PNS a sustainable and easy-to-access multifunctional material.

Mechanochemical Synthesis of Nanoparticles for Potential Antimicrobial Applications

There is an increased interest in porous materials due to their unique properties such as high surface area, enhanced catalytic properties, and biological applications. Various solvent-based approaches have been already used to synthesize porous materials. However, the use of large volume of solvents, their toxicity, and time-consuming synthesis make this process less effective, at least in terms of principles of green chemistry. Mechanochemical synthesis is one of the effective eco-friendly alternatives to the conventional synthesis. It adopts the efficient mixing of reactants using ball milling without or with a very small volume of solvents, gives smaller size nanoparticles (NPs) and larger surface area, and facilitates their functionalization, which is highly beneficial for antimicrobial applications. A large variety of nanomaterials for different applications have already been synthesized by this method. This review emphasizes the comparison between the solvent-based and mechanochemical methods for the synthesis of mainly inorganic NPs for potential antimicrobial applications, although some metal-organic framework NPs are briefly presented too.

Mechanochemical synthesis of non-stoichiometric copper sulfide Cu1.8S applicable as a photocatalyst and antibacterial agent and synthesis scalability verification

An effort to prepare different non-stoichiometric Cu_xS_y compounds starting from elemental precursors using mechanochemistry was made in this study. However, out of the 7 stoichiometries tested, it was only possible to obtain three phases: covellite CuS, chalcocite Cu₂S and digenite Cu_1.8S and their mixtures. To obtain the digenite phase with the highest purity, the Cu : S stoichiometric ratio needed to be fixed at 1.6 : 1. The reaction between copper and sulfur was completed within a second range, however, milling was performed for up to 15 minutes until the equilibrium in phase composition between digenite and covellite was reached. The possibility of preparing the product in a 300 g batch by eccentric vibratory milling in 30 minutes was successfully verified at the end. The estimated crystallite sizes for the digenite Cu_1.8S obtained via lab-scale and scalable experiments were around 12 and 17 nm, respectively. The obtained products were found to be efficient photocatalysts under visible light irradiation in the presence of hydrogen peroxide, being capable of the complete degradation of the Methyl Orange dye in a concentration of 10 mg L^-1 in 2 hours. Finally, the antibacterial potential of both lab-scale and large-scale industrial products was proven and, regardless of the manufacturing scale, the nanoparticles retained their properties against bacterial cells.

Physiotherapeutic Protocol and ZnO Nanoparticles: A Combined Novel Treatment Program against Bacterial Pyomyositis

Myositis tropicans or pyomyositis is a muscle inflammation resulting from a bacterial infection of skeletal muscle (commonly caused by Staphylococcus aureus) that usually leads to hematogenous muscle seeding. The present study was designed to estimate the role of ZnO-NPs and a physiotherapeutic program in the management of induced biceps femoris atrophy in rats through histological, biochemical, and radiological examinations at different time intervals. At the beginning, several bacterial strains were evaluated through a proteolytic enzyme activity assay and the highest activity was recorded with the Staphylococcus aureus strain. ZnO-NPs were synthesized with the arc discharge method with an average size of 19.4 nm. The antibacterial activity of ZnO-NPs was investigated and it was revealed that the prepared ZnO-NPs showed a minimum inhibitory concentration of 8 µg/mL against the tested bacterium. The cytotoxicity of the prepared ZnO-NPs was tested in C2C12 myoblast cells, and it was elaborated that CC50 was 344.16 µg/mL. Biceps femoris pyomyositis was induced with a potent strain (Staphylococcus aureus); then, a physiotherapeutic program combined with the prepared ZnO-NPs treatment protocol was applied and evaluated. The combined program claimed antibacterial properties, preventing muscle atrophy, and resulted in the most comparable value of muscle mass.

Experimental Testing of the Action of Vitamin D and Silicon Chelates in Bone Fracture Healing and Bone Turnover in Mice and Rats

This study presents findings on the biological action of an integrated supplement containing the following components involved in osteogenesis and mineralization: vitamin D and silicon in the bioavailable and soluble form. A hypothesis that these components potentiate one another’s action and make calcium absorption by the body more efficient was tested. Biological tests of the effect of vitamin D and silicon chelates on bone fracture healing and bone turnover were conducted using ICR mice and albino Wistar rats. Radiographic and biochemical studies show that the supplement simultaneously containing silicon chelates and vitamin D stimulates bone tissue regeneration upon mechanical defects and accelerates differentiation of osteogenic cells, regeneration of spongy and compact bones, and restoration of bone structure due to activation of osteoblast performance. Bone structure restoration was accompanied by less damage to skeletal bones, apparently due to better absorption of calcium from food. The studied supplement has a similar effect when used to manage physiologically induced decalcification, thus holding potential for the treatment of osteomalacia during pregnancy or occupational diseases (e.g., for managing bone decalcification in astronauts).

Mechanochemical Strategies for the Preparation of SiO2-Supported AgAu Nanoalloy Catalysts

Silver-gold nanoalloys were prepared from their metal salts precursors through bottom-up mechanochemical synthesis, using one-pot or galvanic replacement reaction strategies. The nanostructures were prepared over amorphous SiO2 as an inert supporting material, facilitating their stabilization without the use of any stabilizing agent. The nanomaterials were extensively characterized, confirming the formation of the bimetallic nanostructures. The nanoalloys were tested as catalysts in the hydrogenation of 2-nitroaniline and exhibited up to 4-fold the rate constant and up to 37% increased conversion compared to the respective single metal nanoparticles. Our approach is advantageous to produce nanoparticles with clean surfaces with available catalytic sites, directly in the solid-state and in an environmentally friendly manner.

Preparation and catalytic properties of polydopamine-modified polyacrylonitrile fibers functionalized with silver nanoparticles

Fiber-supported catalysts have attracted much attention due to their large specific surface area, high catalytic activity, and good recyclability. Functional polyacrylonitrile fibers were prepared by immersion of polyacrylonitrile fibers at room temperature in an alkaline dopamine (pH = 8.5) aqueous solution which can undergo self-polymerization and reduce silver ions to silver nanoparticles with mild reducibility and adsorption. The surface of the polyacrylonitrile fiber (PAN) was wrapped with a layer of polydopamine (PDA), and silver nanoparticles (Ag NPs) were adsorbed on the surface of PDA, forming an efficient fiber catalyst. The morphology and chemical composition of the catalyst material were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) patterns, and Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS). The catalytic activity of the nanocomposite was evaluated for the reduction reaction of 4-nitrophenol using sodium borohydride (NaBH₄) at 35 °C with a material molar ratio of 1 : 10 and a fiber loaded catalysis dosage of 40 mg. The liquid phase yield can reach 98% in 30 minutes and can be reused after washing with ethanol. Moreover, the composite material exhibited a good stability up to 10 cycles without a significant loss of its catalytic activity. The results show that the catalyst is easy to recover from the reaction system and has maintained good stability and catalytic activity after many cycles.

Via the help of polydopamine, polyacrylonitrile fiber catalysts functionalized with silver nanoparticles were prepared and employed for the reduction reaction of 4-nitrophenol to 4-aminophenol, with a yield of 98% in 30 minutes, and can be reused for up to 10 cycles.

Characterization and Antimicrobial Activity of Silver Nanoparticles Synthesized with the Peel Extract of Mango

The green synthesis of silver nanoparticles (AgNPs) from biological waste, as well as their excellent antibacterial properties, is currently attracting significant research attention. This study synthesized AgNPs from different mango peel extract concentrations while investigating their characteristics and antibacterial properties. The results showed that the AgNPs were irregular with rod-like, spherical shapes and were detected in a range of 25 nm to 75 nm. The AgNPs displayed antibacterial activity against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus), showing a more significant impact when synthesized with 0.20 g/mL of mango peel extract. Therefore, the antibacterial effect of different diluted AgNP concentrations on the growth kinetic curves of E. coli and S. aureus after synthesis with 0.20 g/mL mango peel extract was analyzed. The results indicated that the AgNP antibacterial activity was higher against S. aureus than against E. coli, while the AgNP IC50 in these two strains was approximately 1.557 mg/mL and 2.335 mg/L, respectively. This research provides new insights regarding the use of postharvest mango byproducts and the potential for developing additional AgNP composite antibacterial materials for fruit and vegetable preservation.

Green synthesis of antibacterial and cytotoxic silver nanoparticles by Piper nigrum seed extract and development of antibacterial silver based chitosan nanocomposite

In the present study, we have used seed extract of P. nigrum as an effective reducing agent for the synthesis of silver nanoparticles (Ag NPs) and silver based chitosan nanocomposite (Ag/CS NC). The silver nanoparticles were characterized by UV-Vis spectroscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and Fourier transform infrared spectroscopy (FTIR). The appearance of a surface plasmon resonance (SPR) peak located at 430 nm reveals the formation of silver nanoparticles. The TEM analysis indicates that the attained silver nanoparticles were mostly in spherical shapes with sizes ranging between 15 and 38 nm. The high resolution liquid chromatography with mass spectroscopy (HR-LCMS) analysis was performed to screen the phytochemical constituents of P. nigrum seed extract. The silver nanoparticles synthesized by P. nigrum seed extract exhibited effective antibacterial activity against Bacillus subtilis (B. subtilis) and Escherichia coli (E. coli). In addition, the silver nanoparticles showed potent cytotoxicity against hazardous human cancer cell lines MDA-MB-231, PANC-1, SKOV-3, PC-3 and Hela. The observation of bright spots in the TEM dark field images represents the presence of Ag in CS suspension. Besides, the Ag/CS NC coated cotton fabric substantially showed remarkable antibacterial activity against B. subtilis and E. coli.