Enhanced Li-Ion Rate Capability and Stable Efficiency Enabled by MoSe2 Nanosheets in Polymer-Derived Silicon Oxycarbide Fiber Electrodes

C60 Fullerene-Reinforced Silicon Oxycarbide Composite Fiber Mats: Performance as Li-Ion Battery Electrodes

Precursor-derived silicon oxycarbide (SiOC) has emerged as a potential high-capacity anode material for rechargeable Li-ion batteries. The polymer processing and pyrolysis route, a hallmark of polymer-derived ceramics, allows chemical interfacing with a variety of nanoprecursors and nanofiller phases to produce composites with low-dimensional structures such as fibers and coatings not readily attained in traditional sintered ceramics. Here, buckminsterfullerene or C60 was introduced as a filler phase in a hybrid precursor of 1,3,5,7-tetramethyl-1,3,5,7-tetravinyl-cyclotetrasiloxane (TTCS) along with polyvinylpyrrolidone or PVP as a spinning agent to fabricate electrospun fiber mats, which upon a high-heat treatment transformed to a C60-reinforced SiOC ceramic composite. Tested as the self-supporting working electrode in a Li-ion half-cell, C60-reinforced fiber mats show a much-improved reversible capacity (825 mA h g-1), nearly 100% Coulombic efficiency, and superior rate capability with low-capacity decay at high currents (only 25.5% decay at 800 mA g-1) compared to neat C60 and neat carbonized fiber electrodes.

Addressing Irreversibility and Structural Distortion in WS2 Inorganic Fullerene-Like Nanoparticles: Effects of Voltage Cutoff Experiments in Beyond Li+-Ion Storage Applications

Large interlayer spacing beneficially allows Na+- and K+-ion storage in transition-metal dichalcogenide (TMD)-based electrodes, but side reactions and volume change, which pulverize the TMD crystalline structure, are persistent challenges for the utilization of these materials in next-generation devices. This study first determines whether irreversibility due to structural distortion, which results in poor cycling stability, is also apparent in the case of inorganic fullerene-like (IF) tungsten disulfide (WS2) nanocages (WS2IF). To address these problems, this study proposes upper and lower voltage cutoff experiments to limit specific reactions in Na+/WS2IF and K+/WS2IF half-cells. Three-dimensional (3D) differential capacity curves and derived surface plots highlight the continuation of reversible reactions when a high upper cutoff technique is applied, thereby indirectly suggesting restricted structural dissolution. This resulted in improved capacity retention with stable performance and a higher Coulombic efficiency, laying the ground for the use of TMD-based materials beyond Li+-ion storage devices.

WS2 Nanotube-Embedded SiOC Fibermat Electrodes for Sodium-Ion Batteries

Layered transition metal dichalcogenides (TMDs) such as tungsten disulfide (WS₂) are promising materials for a wide range of applications, including charge storage in batteries and supercapacitors. Nevertheless, TMD-based electrodes suffer from bottlenecks such as capacity fading at high current densities, voltage hysteresis during the conversion reaction, and polysulfide dissolution. To tame such adverse phenomena, we fabricate composites with WS₂ nanotubes. Herein, we report on the superior electrochemical performance of ceramic composite fibers comprising WS₂ nanotubes (WS₂NTs) embedded in a chemically robust molecular polymer-derived ceramic matrix of silicon-oxycarbide (SiOC). Such a heterogeneous fiber structure was obtained via electrospinning of WS₂NT/preceramic polymer solution followed by pyrolysis at elevated temperatures. The electrode capacity fading in WS₂NTs was curbed by the synergistic effect between WS₂NT and SiOC. As a result, the composite electrode exhibits high initial capacity of 454 mAh g^-1 and the capacity retention approximately 2-3 times higher than that of the neat WS₂NT electrode.

Recent advances in precursor-derived ceramics integrated with two-dimensional materials

This review focused on the recent advances in precursor-derived ceramics integrated with two-dimensional materials. Their fabrication methods, structures and applications were discussed in detail and the perspectives in this field were presented.