Study of the Interaction of Ti-Zn as a Mixed Oxide at Different pH Values Synthesized by the Sol-Gel Method and Its Antibacterial Properties

A Novel Method for the Fabrication of Antibacterial Stainless Steel with Uniform Silver Dispersions by Silver Nanoparticle/Polyethyleneimine Composites

Only a few studies have so far focused on the addition of silver to SS316L alloys by conventional sintering methods. Unfortunately, the metallurgical process of silver-containing antimicrobial SS is greatly limited due to the extremely low solubility of silver in iron and its tendency to precipitate at the grain boundaries, resulting in an inhomogeneous distribution of the antimicrobial phase and loss of antimicrobial properties. In this work, we present a novel approach to fabricate antibacterial stainless steel 316L by functional polyethyleneimine-glutaraldehyde copolymer (PEI-co-GA/Ag catalyst) composites. PEI is a highly branched cationic polymer, which makes it exhibit very good adhesion on the surface of the substrate. Unlike the effect of the conventional silver mirror reaction, the introduction of functional polymers can effectively improve the adhesion and distribution of Ag particles on the surface of 316LSS. It can be seen from the SEM images that a large number of silver particles are retained and well dispersed in 316LSS after sintering. PEI-co-GA/Ag 316LSS exhibits excellent antimicrobial properties and does not release free silver ions to affect the surrounding environment. Furthermore, the probable mechanism for the influence of the functional composites on the enhancement of adhesion is also proposed. The formation of a large number of hydrogen bonds and van der Waals forces, as well as the negative zeta potential of the 316LSS surface, can effectively enable the formation of a tight attraction between the Cu layer and the surface of 316LSS. These results meet our expectations of designing passive antimicrobial properties on the contact surface of medical devices.

PLGA–TiO2 as a Carrier System for Drug Release

This paper reports the results of the PLGA–TiO2 nanocomposite regarding the green synthesis of titanium dioxide nanoparticles using a natural extract, its characterization, and encapsulation with poly(lactic-co-glycolic acid) (PLGA). UV–visible spectrometry was used for the identification of terpenes present in the extracts. The morphology of the nanoparticles was determined by scanning electron microscopy. Infrared spectroscopy was used for the determination of functional groups, while X-ray diffraction was used to determine the crystal structure. The analysis of the extended release of the encapsulated extract in the matrix of the nanomaterial resulted in a maximum visible UV absorbance at approximately 260 nm and confirmed the synthesis of titanium dioxide nanoparticles. Moreover, terpenes enhance synthesis and stabilize titanium dioxide nanoparticles. The synthesized structures are spherical and amorphous, 44 nm in size, and encapsulated at 65 nm.

Photodegradation and Mineralization of Phenol Using TiO2Coated γ-Al2O3: Effect of Thermic Treatment

It is well-known that γ-Al2O3 possesses large, specific areas and high thermal, chemical, and mechanical resistance. Due to this, it is the most-used support for catalysts, in this case TiO2, as it enables it to achieve better dispersion and improves the activity in catalytic photodegradation reactions. In a previous work, it was observed that the optimal content of TiO2 in γ-Al2O3 was around 15% since the degradation of phenol results were maximized and a synergistic effect was generated by the interaction of both oxides. In addition, an increase in acidity crystal size and the generation of localized, oxygen-vacant, electronic states in the forbidden band of γ-Al2O3, were observed. This study focuses on the effect of the calcination temperature on a γ-Al2O3-TiO2 catalyst (15% w/w of TiO2) and its impact on photocatalytic activity. The catalysts prepared here were characterized by X-ray diffraction, N2 adsorption–desorption, FTIR-pyridine adsorption, MAS-NMR, HRTEM-FFT, UV-vis, and fluorescence spectroscopy.