Enhanced Antibacterial Activity of Poly (dimethylsiloxane) Membranes by Incorporating SiO2 Microspheres Generated Silver Nanoparticles

Development of PDMS/TiO2/Ag3PO4 antibacterial coating on 316L/PDMS implants: Evaluation of superhydrophobicity, bio-corrosion, mechanical behaviour, surface nanostructure and chemistry

Nanocomposite coatings based on polydimethylsiloxane were developed by adding silver phosphate and titania nanoparticles with a PDMS pre-layer for 316L stainless steel. FTIR spectra and XRD patterns confirmed the synthesis of TiO2 and Ag3PO4 nanoparticles and nanocomposite coating. FESM and AFM images show that with the increase of Ag3PO4 nanoparticles, the roughness of coatings increased (Ra and Rq for adding 7 wt% of Ag3PO4 coating was 29 and 293 nm). The wettability results demonstrated that the presence of 7 wt% Ag3PO4 nanoparticles in the coating has the highest water contact angle (152 °). Nano-scratch results proved that creating a pre-layer of PDMS can increase the scratch resistance of PDMS + TiO2+Ag3PO4 nanocomposite coating (displacement and scratch coefficient were 408 nm and 0.07μΝ-1/2 with the pre-layer). Corrosion current density of 316lSS with PDMS + TiO2+Ag3PO4 coating was 0.00045 μA/cm2, while for 316LSS with pure PDMS coating was 0.00114 μA/cm2 at 37 °C in PBS solution. The Nyquist curves showed the diameter of the semicircle for the nanocomposite coating was larger than pure PDMS coating, which indicates the higher corrosion resistance of the nanocomposite coating (5.98 × 107 Ω). By increasing Ag3PO4 nanoparticles from 1 to 7 wt%, the number of E. coli bacteria in contact with the nanocomposite decreased significantly from 580000 to 31000 CFU/cm2. In the disk diffusion test, the largest inhibition zone was related to the nanocomposite coating with the addition of 7 wt% Ag3PO4 (23 mm). Therefore, the PDMS + TiO2+Ag3PO4 nanocomposite coating has improved properties such as superhydrophobicity, advanced mechanical behavior, bio-corrosion resistance, and antibacterial activity.

Functionalized Self-Assembled Monolayers: Versatile Strategies to Combat Bacterial Biofilm Formation

Bacterial infections due to biofilms account for up to 80% of bacterial infections in humans. With the increased use of antibiotic treatments, indwelling medical devices, disinfectants, and longer hospital stays, antibiotic resistant infections are sharply increasing. Annual deaths are predicted to outpace cancer and diabetes combined by 2050. In the past two decades, both chemical and physical strategies have arisen to combat biofilm formation on surfaces. One such promising chemical strategy is the formation of a self-assembled monolayer (SAM), due to its small layer thickness, strong covalent bonds, typically facile synthesis, and versatility. With the goal of combating biofilm formation, the SAM could be used to tether an antibacterial agent such as a small-molecule antibiotic, nanoparticle, peptide, or polymer to the surface, and limit the agent’s release into its environment. This review focuses on the use of SAMs to inhibit biofilm formation, both on their own and by covalent grafting of a biocidal agent, with the potential to be used in indwelling medical devices. We conclude with our perspectives on ongoing challenges and future directions for this field.

An Overview of Antimicrobial Properties of Carbon Nanotubes-Based Nanocomposites

The development of carbon-based nanomaterials has extensively facilitated new discoveries in various fields. Carbon nanotube-based nanocomposites (CNT-based nanocomposites) have lately recognized as promising biomaterials for a wide range of biomedical applications due to their unique electronic, mechanical, and biological properties. Nanocomposite materials such as silver nanoparticles (AgNPs), polymers, biomolecules, enzymes, and peptides have been reported in many studies, possess a broad range of antibacterial activity when incorporated with carbon nanotubes (CNTs). It is crucial to understand the mechanism which governs the antimicrobial activity of these CNT-based nanocomposite materials, including the decoupling individual and synergistic effects on the cells. In this review, the interaction behavior between microorganisms and different types of CNT-based nanocomposites is summarized to understand the respective antimicrobial performance in different conditions. Besides, the current development stage of CNT-based nanocomposite materials, the technical challenges faced, and the exceptional prospect of implementing potential antimicrobial CNT-based nanocomposite materials are also discussed.

One-step preparation of antimicrobial silicone materials based on PDMS and salicylic acid: insights from spatially and temporally resolved techniques

In this work, we introduce a one-step strategy that is suitable for continuous flow manufacturing of antimicrobial PDMS materials. The process is based on the intrinsic capacity of PDMS to react to certain organic solvents, which enables the incorporation of antimicrobial actives such as salicylic acid (SA), which has been approved for use in humans within pharmaceutical products. By combining different spectroscopic and imaging techniques, we show that the surface properties of PDMS remain unaffected while high doses of the SA are loaded inside the PDMS matrix. The SA can be subsequently released under physiological conditions, delivering a strong antibacterial activity. Furthermore, encapsulation of SA inside the PDMS matrix ensured a diffusion-controlled release that was tracked by spatially resolved Raman spectroscopy, Attenuated Total Reflectance IR (ATR-IR), and UV-Vis spectroscopy. The biological activity of the new material was evaluated directly at the surface and in the planktonic state against model pathogenic bacteria, combining confocal laser scanning microscopy, electron microscopy, and cell viability assays. The results showed complete planktonic inhibition for clinically relevant strains of Staphylococcus aureus and Escherichia coli, and a reduction of up to 4 orders of magnitude for viable sessile cells, demonstrating the efficacy of these surfaces in preventing the initial stages of biofilm formation. Our approach adds a new option to existing strategies for the antimicrobial functionalisation of a wide range of products such as catheters, wound dressings and in-dwelling medical devices based on PDMS.

Sol-Gel Nanocomposite Coatings for Preventing Biofilm Formation on Contact Lens Cases

Purpose

To evaluate the efficacy of a nanosilver-based sol–gel coating in preventing biofilm formation on contact lens cases.

Methods

An organic–inorganic hybrid silica–zirconia sol formulation with immobilized silver nanoparticles was deposited on contact lens case coupons. The coated and uncoated coupons were subjected to biofilm formation to Gram-negative and Gram-positive keratitis isolates and ATCC strains using a standard protocol. The biofilms were evaluated using crystal violet, MTT assay, and scanning electron microscope (SEM) examination. The duration of efficacy of the coating was evaluated by exposing the coated and uncoated coupons to a multipurpose lens cleaning solution for various durations up to 30 days and comparing their biofilm characteristics. The cytotoxicity of the coated surface was assessed using cell culture studies.

Results

Cross-hatch tests and SEM confirmed the presence of a uniform, well-adhered coating on the surface. The coating resulted in a nearly 95% reduction in biofilm formation of the tested bacteria and was effective despite exposures of up to 30 days to a multipurpose lens cleaning solution. The coating did not exhibit cytotoxicity to human corneal epithelial cells.

Conclusions

The silver nanoparticle-based coating exhibits a good antibiofilm property for both Gram-negative bacilli and Gram-positive cocci and is promising for commercial use in preventing contact lens-related infections.

Translational Relevance

Biofilm formation on lens cases continues to be an important concern. The proposed coating will help reduce such formations, thus reducing the risk of lens-associated microbial keratitis.

Carbon Nanotube/Poly(dimethylsiloxane) Composite Materials to Reduce Bacterial Adhesion

Different studies have shown that the incorporation of carbon nanotubes (CNTs) into poly(dimethylsiloxane) (PDMS) enables the production of composite materials with enhanced properties, which can find important applications in the biomedical field. In the present work, CNT/PDMS composite materials have been prepared to evaluate the effects of pristine and chemically functionalized CNT incorporation into PDMS on the composite's thermal, electrical, and surface properties on bacterial adhesion in dynamic conditions. Initial bacterial adhesion was studied using a parallel-plate flow chamber assay performed in conditions prevailing in urinary tract devices (catheters and stents) using Escherichia coli as a model organism and PDMS as a control due to its relevance in these applications. The results indicated that the introduction of the CNTs in the PDMS matrix yielded, in general, less bacterial adhesion than the PDMS alone and that the reduction could be dependent on the surface chemistry of CNTs, with less adhesion obtained on the composites with pristine rather than functionalized CNTs. It was also shown CNT pre-treatment and incorporation by different methods affected the electrical properties of the composites when compared to PDMS. Composites enabling a 60% reduction in cell adhesion were obtained by CNT treatment by ball-milling, whereas an increase in electrical conductivity of seven orders of magnitude was obtained after solvent-mediated incorporation. The results suggest even at low CNT loading values (1%), these treatments may be beneficial for the production of CNT composites with application in biomedical devices for the urinary tract and for other applications where electrical conductance is required.