Morphology, Photocatalytic and Antimicrobial Properties of TiO2 Modified with Mono- and Bimetallic Copper, Platinum and Silver Nanoparticles

Photobiocidal Activity of TiO2/UHMWPE Composite Activated by Reduced Graphene Oxide under White Light

Herein, we introduce a photobiocidal surface activated by white light. The photobiocidal surface was produced through thermocompressing a mixture of titanium dioxide (TiO2), ultra-high-molecular-weight polyethylene (UHMWPE), and reduced graphene oxide (rGO) powders. A photobiocidal activity was not observed on UHMWPE-TiO2. However, UHMWPE-TiO2@rGO exhibited potent photobiocidal activity (>3-log reduction) against Staphylococcus epidermidis and Escherichia coli bacteria after a 12 h exposure to white light. The activity was even more potent against the phage phi 6 virus, a SARS-CoV-2 surrogate, with a >5-log reduction after 6 h exposure to white light. Our mechanistic studies showed that the UHMWPE-TiO2@rGO was activated only by UV light, which accounts for 0.31% of the light emitted by the white LED lamp, producing reactive oxygen species that are lethal to microbes. This indicates that adding rGO to UHMWPE-TiO2 triggered intense photobiocidal activity even at shallow UV flux levels.

Innovative Fabrication of Metal Alloy Structures via Laser-Induced Forward Transfer on Flexible Substrates

Laser-induced forward transfer is a contactless, nozzle free process which enables accurate, precise and fast development of 3D structures. However, a number of shortcomings such as shockwave generation, poor adhesion to receiver substrates and uniform depositions limit LIFT to be utilized. Therefore, this research tends to put forward easy and effective solutions for successful mitigation of the LIFT limitations. Receiver surface modifications and low-pressure conditions are introduced through laser surface texturing (LST) and a vacuum pump. A number of textures and orientations are investigated for determining the optimal copper (Cu) deposition. Furthermore, utilization of the same laser system for LST enables the manufacturing process cost and time effective. In addition to Cu depositions, additive layers of silver (Ag) and platinum (Pt) are deposited. Finally, Ag and Pt micropillars are fabricated on their respective additive layers leading to formation of Cu-Ag and Cu-Pt alloys structure. Subsequently, electrical and material characterizations are made to validate for potential applications. Experimental evidence shows greater adhesion with electrical properties for LST-based LIFT in low pressure conditions. Finally, an energy analysis is performed based on theoretical and finite element methods (FEM) to gain greater insights into mechanics of the LIFT process.

Current perspectives of metal-based nanomaterials as photocatalytic antimicrobial agents and their therapeutic modes of action: A review

Efforts to restrict the emergence and progression of multidrug-resistant bacterial strains should heavily involve the scientific community, including government bodies, researchers, and industries, in developing new and effective photocatalytic antimicrobial agents. Such changes warrant the modernization and upscaling of materials synthesis laboratories to support and expedite the mass production of materials at the industrial scale for the benefit of humankind and the environment. Despite the massive volume of publications reporting the potential usage of different types of metal-based nanomaterials as antimicrobial agents, reviews uncovering the similarities and differences among the various products remain lacking. This review details the basic and unique properties of metal-based nanoparticles, their use as photocatalytic antimicrobial agents, and their therapeutic modes of action. It shall be noted that compared to traditional antibiotics, the mode of action of photocatalytic metal-based nanomaterials for killing microorganisms are completely different, despite displaying promising performance against antibiotic-resistant bacteria. Besides, this review uncovers the differences in the mode of actions of metal oxide nanoparticles against different types of bacteria, as well as towards viruses. Last but not least, this review comprehensively describes previous published clinical trials and medical usages involving contemporary photocatalytic antimicrobial agents.

Influence of Ag size and shape in dye photodegradation using silver nanoparticle/ZnO nanohybrids and polychromatic light

In this work, we propose zinc oxide (ZnO) surface functionalization with plasmonic silver nanoparticles (AgNP) of different sizes and shapes (spheres, prisms, and rods) creating ZnO/AgNP nanohybrids. These were characterized by UV-Vis spectroscopy, X-ray diffraction, transmission electron microscopy, Fourier-transform infrared spectroscopy, diffuse reflectance spectroscopy, and photoluminescence spectroscopy. Surface functionalization with AgNP improved photocatalyst electronic properties, its visible light absorption, and slow electron/hole recombination on the ZnO surface. Photocatalysis assays performed with a polychromatic Hg lamp degraded methyl orange, a model of persistent organic pollutant in water. A systematic study showed that the photodegradation kinetics of the nanohybrids are significantly more efficient than pure ZnO (up to 18 times) and that AgNP size and especially its shape are important in dye degradation. Mechanistic studies revealed that degradation occurred by direct dye reduction on the ZnO surface holes, ZnO electron transfer to Ag followed by •O₂^- formation, and direct injection of AgNP hot electrons in the ZnO conduction band. The last effect was stronger for anisotropic AgNP, which explains their high kinetic degradation rates. Therefore, the rational design in ZnO/AgNP nanohybrid engineering and a systematic approach used in this manuscript allowed a detailed description of photodegradation process that occur at ZnO/AgNP interface. Our results are not conclusive about AgNP size; on the other hand, it clearly demonstrates that anisotropic nanoparticles (as Ag rods and prims) present superior photodegradation efficiency and are promising particles for further large-scale use of solar-irradiated nanohybrids.

Using visible light to activate antiviral and antimicrobial properties of TiO2 nanoparticles in paints and coatings: focus on new developments for frequent-touch surfaces in hospitals

The COVID-19 pandemic refocused scientists the world over to produce technologies that will be able to prevent the spread of such diseases in the future. One area that deservedly receives much attention is the disinfection of health facilities like hospitals, public areas like bathrooms and train stations, and cleaning areas in the food industry. Microorganisms and viruses can attach to and survive on surfaces for a long time in most cases, increasing the risk for infection. One of the most attractive disinfection methods is paints and coatings containing nanoparticles that act as photocatalysts. Of these, titanium dioxide is appealing due to its low cost and photoreactivity. However, on its own, it can only be activated under high-energy UV light due to the high band gap and fast recombination of photogenerated species. The ideal material or coating should be activated under artificial light conditions to impact indoor areas, especially considering wall paints or frequent-touch areas like door handles and elevator buttons. By introducing dopants to TiO₂ NPs, the bandgap can be lowered to a state of visible-light photocatalysis occurring. Naturally, many researchers are exploring this property now. This review article highlights the most recent advancements and research on visible-light activation of TiO₂-doped NPs in coatings and paints. The progress in fighting air pollution and personal protective equipment is also briefly discussed.

Graphical Abstract

Indoor visible-light photocatalytic activation of reactive oxygen species (ROS) over TiO₂ nanoparticles in paint to kill bacteria and coat frequently touched surfaces in the medical and food industries.

Preparation, Antimicrobial Properties under Different Light Sources, Mechanisms and Applications of TiO2: A Review

Traditional antimicrobial methods, such as antibiotics and disinfectants, may cause adverse effects, such as bacterial resistance and allergic reactions. Photocatalysts based on titanium dioxide (TiO₂) have shown great potential in the field of antimicrobials because of their high efficiency, lack of pollution, and lack of side effects. This paper focuses on the antimicrobial activity of TiO₂ under different light sources. To improve the photocatalytic efficiency of TiO₂, we can reduce electron-hole recombination and extend the photocatalytic activity to the visible light region by doping with different ions or compounds and compounding with polymers. We can also improve the surface properties of materials, increase the contact area with microorganisms, and further enhance the resistance to microorganisms. In addition, we also reviewed their main synthesis methods, related mechanisms, and main application fields to provide new ideas for the enhancement of photocatalytic microorganism performance and application popularization in the future.

Plasmonic Hybrid Nanostructures in Photocatalysis: Structures, Mechanisms, and Applications

(Sun)Light is an abundantly available sustainable source of energy that has been used in catalyzing chemical reactions for several decades now. In particular, studies related to the interaction of light with plasmonic nanostructures have been receiving increased attention. These structures display the unique property of localized surface plasmon resonance, which converts light of a specific wavelength range into hot charge carriers, along with strong local electromagnetic fields, and/or heat, which may all enhance the reaction efficiency in their own way. These unique properties of plasmonic nanoparticles can be conveniently tuned by varying the metal type, size, shape, and dielectric environment, thus prompting a research focus on rationally designed plasmonic hybrid nanostructures. In this review, the term "hybrid" implies nanomaterials that consist of multiple plasmonic or non-plasmonic materials, forming complex configurations in the geometry and/or at the atomic level. We discuss the synthetic techniques and evolution of such hybrid plasmonic nanostructures giving rise to a wide variety of material and geometric configurations. Bimetallic alloys, which result in a new set of opto-physical parameters, are compared with core-shell configurations. For the latter, the use of metal, semiconductor, and polymer shells is reviewed. Also, more complex structures such as Janus and antenna reactor composites are discussed. This review further summarizes the studies exploiting plasmonic hybrids to elucidate the plasmonic-photocatalytic mechanism. Finally, we review the implementation of these plasmonic hybrids in different photocatalytic application domains such as H₂ generation, CO₂ reduction, water purification, air purification, and disinfection.

Effect of TiO2 Concentration on Microstructure and Properties of Composite Cu-Sn-TiO2 Coatings Obtained by Electrodeposition

In this work, Cu–Sn–TiO₂ composite coatings were electrochemically obtained from a sulfate bath containing 0–10 g/L of TiO₂ nanoparticles. The effect of TiO₂ particles on kinetics of cathodic electrodeposition has been studied by linear sweep voltammetry and chronopotentiometry. As compared to the Cu–Sn alloy, the Cu–Sn–TiO₂ composite coatings show rougher surfaces with TiO₂ agglomerates embedded in the metal matrix. The highest average amount of included TiO₂ is 1.7 wt.%, in the case of the bath containing 5 g/L thereof. Composite coatings showed significantly improved antibacterial properties towards E. coli ATCC 8739 bacteria as compared to the Cu–Sn coatings of the same composition. Such improvement has been connected with the corrosion resistance of the composites studied by linear polarization and electrochemical impedance spectroscopy. In the bacterial media and 3% NaCl solutions, Cu–Sn–TiO₂ composite coatings have lower corrosion resistance as compared to Cu–Sn alloys, which is caused by the nonuniformity of the surface.

Recent progress on Ag/TiO2 photocatalysts: photocatalytic and bactericidal behaviors

For many decades, titanium dioxide (TiO₂) semiconductor has been extensively applied in several environmental applications due to its higher photocatalytic performances toward different organic pollutants, pharmaceutical compounds, and bacteria. However, its shortfall response to visible light, and the expeditious recombination rate of the photogenerated electron-hole pairs, hampers its utilization. Doping TiO₂ semiconductor with silver nanoparticles is a sound strategy to (1) extend its photocatalytic activity to visible light, (2) prevent the electron/holes pairs recombination due to the formation of the Schottky barrier at the interfaces with TiO₂ that act as an electron-trapping center, and (3) enhance its bactericide performances. This review focuses on the recent progress on silver-doped titanium dioxide (Ag/TiO₂)-based photocatalysts. It addresses a wide range of Ag/TiO₂ synthesis techniques, their physicochemical properties and discusses thoroughly the important role of silver (Ag) nanoparticles in enhancing the removal capacity and antibacterial performances of the Ag/TiO₂ photocatalysts.

Hydrothermal Cobalt Doping of Titanium Dioxide Nanotubes towards Photoanode Activity Enhancement

Doping and modification of TiO2 nanotubes were carried out using the hydrothermal method. The introduction of small amounts of cobalt (0.1 at %) into the structure of anatase caused an increase in the absorption of light in the visible spectrum, changes in the position of the flat band potential, a decrease in the threshold potential of water oxidation in the dark, and a significant increase in the anode photocurrent. The material was characterized by the SEM, EDX, and XRD methods, Raman spectroscopy, XPS, and UV-Vis reflectance measurements. Electrochemical measurement was used along with a number of electrochemical methods: chronoamperometry, electrochemical impedance spectroscopy, cyclic voltammetry, and linear sweep voltammetry in dark conditions and under solar light illumination. Improved photoelectrocatalytic activity of cobalt-doped TiO2 nanotubes is achieved mainly due to its regular nanostructure and real surface area increase, as well as improved visible light absorption for an appropriate dopant concentration.

Antiviral Effect of Visible Light-Sensitive CuxO/TiO2 Photocatalyst

Photocatalysis is an effective technology for preventing the spread of pandemic-scale viruses. This review paper presents an overview of the recent progress in the development of an efficient visible light-sensitive photocatalyst, i.e., a copper oxide nanoclusters grafted titanium dioxide (CuxO/TiO2). The antiviral CuxO/TiO2 photocatalyst is functionalised by a different mechanism in addition to the photocatalytic oxidation process. The CuxO nanocluster consists of the valence states of Cu(I) and Cu(II); herein, the Cu(I) species denaturalizes the protein of the virus, thereby resulting in significant antiviral properties even under dark conditions. Moreover, the Cu(II) species in the CuxO nanocluster serves as an electron acceptor through photo-induced interfacial charge transfer, which leads to the formation of an anti-virus Cu(I) species and holes with strong oxidation power in the valence band of TiO2 under visible-light irradiation. The antiviral function of the CuxO/TiO2 photocatalyst is maintained under indoor conditions, where light illumination is enabled during the day but not during the night; this is because the remaining active Cu(I) species works under dark conditions. The CuxO/TiO2 photocatalyst can thus be used to reduce the risk of virus infection by acting as an antiviral coating material.

Defective TiO2 Core-Shell Magnetic Photocatalyst Modified with Plasmonic Nanoparticles for Visible Light-Induced Photocatalytic Activity

In the presented work, for the first time, the metal-modified defective titanium(IV) oxide nanoparticles with well-defined titanium vacancies, was successfully obtained. Introducing platinum and copper nanoparticles (NPs) as surface modifiers of defective d-TiO2 significantly increased the photocatalytic activity in both UV-Vis and Vis light ranges. Moreover, metal NPs deposition on the magnetic core allowed for the effective separation and reuse of the nanometer-sized photocatalyst from the suspension after the treatment process. The obtained Fe3O4@SiO2/d-TiO2-Pt/Cu photocatalysts were characterized by X-ray diffractometry (XRD) and specific surface area (BET) measurements, UV-Vis diffuse reflectance spectroscopy (DR-UV/Vis), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Further, the mechanism of phenol degradation and the role of four oxidative species (h+, e−, •OH, and •O2−) in the studied photocatalytic process were investigated.

Hybrid TiO2-Polyaniline Photocatalysts and their Application in Building Gypsum Plasters

Hybrid materials of conjugated polymer and titanium(IV) oxide have attracted considerable attention concerning their potential benefits, including (i) efficient exploitation of visible light, (ii) a high adsorption capacity for organic contaminants, (iii) and effective charge carriers separation. The new class of the photocatalysts is promising for the removal of environmental pollutants in both aqueous and gaseous phases. For the first time, in this study, the polyaniline (PANI)-TiO2 hybrid composite was used for the degradation of phenol in water and toluene in the gas phase. Polyaniline-TiO2 was prepared by the in situ polymerization of aniline on the TiO2 surface. The obtained hybrid material was characterized by diffuse reflectance spectroscopy (DR/UV-Vis), X-ray diffraction (XRD), fast-Fourier transformation spectroscopy (FTIR), photoluminescence (PL) spectroscopy, microscopy analysis (SEM/TEM), and thermogravimetric analysis (TGA). An insight into the mechanism was shown based on the photodegradation analysis of charge carrier scavengers. Polyaniline is an efficient TiO2 photosensitizer for photodegradation in visible light (λ > 420 nm). The trapping experiments revealed that mainly h+ and ˙OH were the reactive oxygen species that were responsible for phenol degradation. Furthermore, the PANI-TiO2 hybrid nanocomposite was used in gypsum plaster to study the self-cleaning properties of the obtained building material. The effect of PANI-TiO2 content on the hydrophilic/hydrophobic properties and crystallographic structure of gypsum was studied. The obtained PANI-TiO2-modified gypsum plaster had improved photocatalytic activity in the reaction of toluene degradation under Vis light.

Nanoparticles as Anti-Microbial, Anti-Inflammatory, and Remineralizing Agents in Oral Care Cosmetics: A Review of the Current Situation

Many investigations have pointed out widespread use of medical nanosystems in various domains of dentistry such as prevention, prognosis, care, tissue regeneration, and restoration. The progress of oral medicine nanosystems for individual prophylaxis is significant for ensuring bacterial symbiosis and high-quality oral health. Nanomaterials in oral cosmetics are used in toothpaste and other mouthwash to improve oral healthcare performance. These processes cover nanoparticles and nanoparticle-based materials, especially domains of application related to biofilm management in cariology and periodontology. Likewise, nanoparticles have been integrated in diverse cosmetic produces for the care of enamel remineralization and dental hypersensitivity. This review summarizes the indications and applications of several widely employed nanoparticles in oral cosmetics, and describes the potential clinical implementation of nanoparticles as anti-microbial, anti-inflammatory, and remineralizing agents in the prevention of dental caries, hypersensitivity, and periodontitis.

Visible-Light Active Titanium Dioxide Nanomaterials with Bactericidal Properties

This article provides an overview of current research into the development, synthesis, photocatalytic bacterial activity, biocompatibility and cytotoxic properties of various visible-light active titanium dioxide (TiO2) nanoparticles (NPs) and their nanocomposites. To achieve antibacterial inactivation under visible light, TiO2 NPs are doped with metal and non-metal elements, modified with carbonaceous nanomaterials, and coupled with other metal oxide semiconductors. Transition metals introduce a localized d-electron state just below the conduction band of TiO2 NPs, thereby narrowing the bandgap and causing a red shift of the optical absorption edge into the visible region. Silver nanoparticles of doped TiO2 NPs experience surface plasmon resonance under visible light excitation, leading to the injection of hot electrons into the conduction band of TiO2 NPs to generate reactive oxygen species (ROS) for bacterial killing. The modification of TiO2 NPs with carbon nanotubes and graphene sheets also achieve the efficient creation of ROS under visible light irradiation. Furthermore, titanium-based alloy implants in orthopedics with enhanced antibacterial activity and biocompatibility can be achieved by forming a surface layer of Ag-doped titania nanotubes. By incorporating TiO2 NPs and Cu-doped TiO2 NPs into chitosan or the textile matrix, the resulting polymer nanocomposites exhibit excellent antimicrobial properties that can have applications as fruit/food wrapping films, self-cleaning fabrics, medical scaffolds and wound dressings. Considering the possible use of visible-light active TiO2 nanomaterials for various applications, their toxicity impact on the environment and public health is also addressed.