Preparation and Evaluation of Inhalable Amifostine Microparticles Using Wet Ball Milling

High-loading cannabidiol powders for inhalation

Limited attempts have been made previously to develop high-loading CBD inhalable powders, which are essential for high dose delivery. Therefore, this study aimed to develop and characterise inhalable powders with ≥ 95 % w/w CBD by wet ball milling. The effects of magnesium stearate (2 % and 5 %) and inhaler resistance (low-resistance and high-resistance RS01 inhalers) on aerosol performance were also compared. Wet ball milling produced CBD powders with > 50 % production yield. The milled particles showed irregular shapes. The powders were crystalline with minimal amorphous content, low residual solvent level (<1%), and low moisture sorption (<4%). Magnesium stearate improved both the emitted and fine particle fractions. The aerodynamic particle size distribution of the formulations differed between the low-resistance and high-resistance RS01 inhalers. The latter decreased throat deposition but increased inhaler retention. The dissolution profiles showed that all three formulations released CBD steadily and plateaued at 30 min. The best scenario was CBD with 5 % magnesium stearate dispersed from the high resistance RS01 inhaler, showing the highest FPF with the lowest throat deposition. This combination may be tested in vivo in the future to investigate its pharmacokinetic profile.

Design of Experiment (DoE) Approach for Developing Inhalable PLGA Microparticles Loaded with Clofazimine for Tuberculosis Treatment

Tuberculosis (TB) is an airborne bacterial infection caused by Mycobacterium tuberculosis (M. tb), resulting in approximately 1.3 million deaths in 2022 worldwide. Oral therapy with anti-TB drugs often fails to achieve therapeutic concentrations at the primary infection site (lungs). In this study, we developed a dry powder inhalable formulation (DPI) of clofazimine (CFZ) to provide localized drug delivery and minimize systemic adverse effects. Poly (lactic acid-co-glycolic acid) (PLGA) microparticles (MPs) containing CFZ were developed through a single emulsion solvent evaporation technique. Clofazimine microparticles (CFZ MPs) displayed entrapment efficiency and drug loading of 66.40 ± 2.22 %w/w and 33.06 ± 1.45 µg/mg, respectively. To facilitate pulmonary administration, MPs suspension was spray-dried to yield a dry powder formulation (CFZ SD MPs). Spray drying had no influence on particle size (~1 µm), zeta potential (-31.42 mV), and entrapment efficiency. Solid state analysis (PXRD and DSC) of CFZ SD MPs studies demonstrated encapsulation of the drug in the polymer. The drug release studies showed a sustained drug release. The optimized formulation exhibited excellent aerosolization properties, suggesting effective deposition in the deeper lung region. The in vitro antibacterial studies against H37Ra revealed improved (eight-fold) efficacy of spray-dried formulation in comparison to free drug. Hence, clofazimine dry powder formulation presents immense potential for the treatment of tuberculosis with localized pulmonary delivery and improved patient compliance.

Engineering Inhalable Therapeutic Particles: Conventional and Emerging Approaches

Respirable particles are integral to effective inhalable therapeutic ingredient delivery, demanding precise engineering for optimal lung deposition and therapeutic efficacy. This review describes different physicochemical properties and their role in determining the aerodynamic performance and therapeutic efficacy of dry powder formulations. Furthermore, advances in top-down and bottom-up techniques in particle preparation, highlighting their roles in tailoring particle properties and optimizing therapeutic outcomes, are also presented. Practices adopted for particle engineering during the past 100 years indicate a significant transition in research and commercial interest in the strategies used, with several innovative concepts coming into play in the past decade. Accordingly, this article highlights futuristic particle engineering approaches such as electrospraying, inkjet printing, thin film freeze drying, and supercritical processes, including their prospects and associated challenges. With such technologies, it is possible to reshape inhaled therapeutic ingredient delivery, optimizing therapeutic benefits and improving the quality of life for patients with respiratory diseases and beyond.