Recrystallization of commercial carbamazepine samples-a strategy to control dissolution variability

Controlling the crystal structure of succinic acid via microfluidic spray-drying

Many properties of materials, including their dissolution kinetics, hardness, and optical appearance, depend on their structure. Unfortunately, it is often difficult to control the structure of low molecular weight organic compounds that have a high propensity to crystallize if they are formulated from solutions wherein they have a high mobility. This limitation can be overcome by formulating these compounds within small airborne drops that rapidly dry, thereby limiting the time molecules have to arrange into the thermodynamically most stable phase. Such drops can be formed with a surface acoustic wave (SAW)-based spray-drier. In this paper, we demonstrate that the structure of a model low molecular weight compound relevant to applications in pharmacology and food, succinic acid, can be readily controlled with the supersaturation rate. Succinic acid particles preserve the metastable structure over at least 3 months if the initial succinic acid concentration is below 2% of its saturation concentration such that the supersaturation rate is high. We demonstrate that also the stability of the metastable phases against their transformation into the most stable phase increases with decreasing initial solute concentration and hence with increasing supersaturation rate of the spray-dried solution. These insights open up new opportunities to control the crystal structure and therefore properties of low molecular weight compounds that have a high propensity to crystallize.

Carbamazepine polymorphism: a re-visitation using Raman imaging

Raman imaging methods have appeared in the last years as a powerful approach to monitoring the quality of pharmaceutical compounds. Because polymorphism occurs in many crystalline pharmaceutical compounds, it is essential to monitor polymorphic transformations induced by different external stimulus, such as temperature changes, to which those compounds may be submitted. Raman imaging with k-means cluster analysis (CA) is used here as an essential technique to investigate structural and chemical transformations occurring in carbamazepine p-monoclinic (CBZ III) into carbamazepine triclinic (CBZ I) when submitted to temperatures near the melting point of CBZ III (178 °C) and CBZ I (193°C). CBZ III commercial powder and laboratorial prepared CBZ I were analyzed by differential scanning calorimetry, powder X-ray diffraction and Raman spectroscopy with variable temperature. After thermal treatment, the resultant CBZ powder was evaluated by Raman imaging, in which all imaging data was analyzed using CA. Raman imaging allowed the identification of different polymorphs of CBZ (CBZ III and CBZ I) and iminostilbene (IMS), a degradation product of CBZ, in the treated samples, depending on the heating treatment method.

Influence of high pressure compaction on solubility and intrinsic dissolution of ibuprofen binary mixtures employing standard excipients

Enabling formulations often depend on functional excipients. However, the question remains whether excipients regarded as standard establish similar interactions and subsequently improvement of solubility when employed at unusual manufacturing process conditions. In this study, compaction of API under high pressure in the presence of hydrophilic excipients is proposed as a technique to improve the solubility and/or dissolution rate with an acceptable preservation of the supersaturation state. Binary mixtures of ibuprofen (IBU) with hydroxypropyl cellulose, isomalt, mannitol and sorbitol were compacted applying high pressure (500 MPa) with and without a previous co-milling step. Intrinsic dissolution rate (IDR) was selected to characterize and evaluate dissolution performance. The IDR of neat IBU increased from 5 to 88 fold and the aqueous solubility in the range of 3 to 54%. Regarding the polyols isomalt showed the highest impact on solubility and dissolution, without changing the crystallinity of IBU independent of a co-milling step. Even higher impact was achieved in combination with HPC. However, only without a previous co-milling step, ibuprofen remained crystalline, while co-milling induced an amorphous IBU-content of 38%. Based on XRPD and DSC findings, higher IDR and solubility values correlated with crystal modifications as well as IBU/excipient interactions.

Crystallisation parameters effect on the particle size distribution (PSD) of carbamazepine-saccharin (CBZ-SAC) co-crystals in batch cooling crystallisation

The crystallisation parameters effect on the particle size distribution (PSD) of carbamazepine-saccharin (CBZ-SAC) co-crystals in batch cooling crystallisation is presented. The particle size distribution study of CBZ-SAC co-crystals revealed that the multimodal with broad PSD was found for CBZ concentration of 19.14 mg/ml. Meanwhile, the unimodal with broad PSD were observed at CBZ concentration of 17.01 mg/ml and 17.96 mg/Crystal characterisation using differential scanning calorimetry (DSC), X-ray powder diffraction (XRPD), Fourier transform infrared (FTIR) and optical microscopy confirm the solid formed is CBZ-SAC co-crystal Form I with plate-like crystal morphology.

Development of Extended-Release Oral Flexible Tablet (ER-OFT) Formulation for Pediatric and Geriatric Compliance: an Age-Appropriate Formulation

Development of age-appropriate formulation suitable for pediatric and geriatric patients involves various challenges. The objective of this research was to develop extended-release oral flexible tablet (ER-OFT) formulation using carbamazepine (CBZ) as model drug for pediatric and geriatric compliance. ER-microparticles of carbamazepine, a BCS class 2, and narrow therapeutic index (NTI) drug, were prepared using ethyl cellulose as matrixing polymer and hypromellose as hydrophilic pore former. Microparticles were prepared using high-shear granulator fitted with an atomizing spray system. Granulation of carbamazepine and ethyl cellulose (EC-FP) with ethanolic binder solution resulted in ER-microparticles with extended-release >16 h. Release kinetics of ER microparticles showed Higuchi model by drug diffusion and erosion. Korsemeyer-peppas release exponent "n" value 0.42 suggested Fickian diffusion. ER-OFT was prepared by blending of ER-microparticles with water-insoluble compressible aid and disintegrating agent. ER-OFT was characterized for performance characteristics and elemental impurities. As the polymer content in formulation was <10%, the size of ER-OFT was smaller compared to marketed ER-formulations. ER-OFT showed in vitro disintegration time of <30 s as per USP and dispersion time of ∼60 to 180 s in 5 to 10 mL of water. Drug release profiles of ER-microparticles and ER-OFT were comparable as f2 values were >50. In vitro dissolution of ER-OFT was comparable to the marketed ER formulation in the pH range of GIT. ER-OFT can be orally swallowed, orally disintegrating, and used as dispersible tablets. Compared to non-disintegrating type ER-formulations, ER-OFT would provide uniform drug release in GIT with low within-subject variability an essential criterion for NTI drug.