Valorization of Alkaline Peroxide Mechanical Pulp by Metal Chloride-Assisted Hydrotropic Pretreatment for Enzymatic Saccharification and Cellulose Nanofibrillation

Metal ion and hydrogen bonding synergistically mediated carboxylated lignin/cellulose nanofibrils composite film

In order to alleviate the resource and environmental problems caused by plastic film materials, the development of biodegradable cellulose-based films is crucial. Inspired by the strengthening mechanism of cellulose-lignin network from wood, carboxylated lignin (CL) was isolated using maleic acid (MA) pretreatment catalyzed by metal chlorides. Compared with pure MA, the presence of metal ions yielded CL with high carboxyl content (0.34 mmol/g), small size and good dispersibility. CL was then composited with CNF to prepare various CL/cellulose nanofibrils (CNF) composite films. When the addition of ferric chloride was 0.3 mmol/g maleic acid, the corresponding composite films exhibited highest tensile strength (180.0 MPa), Young's modulus (13.0 GPa) and excellent ultraviolet blocking rate (97.0 %). Meanwhile, the interaction forces measured by atomic force microscope showed that the binding between CNF and various CLs (276-406 nN) was higher than that between pure CNFs (202 nN), verifying that CL enhanced the mechanical properties of composite films. In summary, this work constructs a super-strong network between CL and CNF synergistically mediated by metal ion crosslinking and hydrogen bonding, which can be a promising alternative to replace conventional plastics in multiple areas.

Comparison of enzymatic saccharification and lignin structure of masson pine and poplar pretreated by p-Toluenesulfonic acid

p-Toluenesulfonic acid (p-TsOH) with the hydrotropic and recyclable properties is widely used for rapid remove of lignin from lignocelluloses at low temperature (<100 °C). In this work, both softwood masson pine and hardwood poplar were pretreated with p-TsOH under different conditions and then subjected to enzymatic hydrolysis to compare the effect of p-TsOH pretreatment on their saccharification and lignin structure. Results showed p-TsOH has sensitive selectivity to lignin structure during pretreatment. Around 95% of lignin in poplar can be dissolved at 80 °C within 30 min, while for masson pine, the delignification is only 50%. Following enzymatic hydrolysis with cellulase loading of 20 FPU/g-cellulose for 72 h, the highest sugar yield of pretreated poplar and masson pine is 92.13% and 29.46%, respectively, which indicates that p-TsOH pretreatment alone works well with hardwoods (poplar). Structural analysis of removed lignin implies that p-TsOH mainly results in the cleavage of β-aryl ether bonds of lignin side chains, and the aromatic structure of lignin keeps intact. p-TsOH pretreatment shows the key advantages of low cost and rapid delignification for highly enzymatic saccharification, and provides a promising and green pathway for the development of low cost and sustainable bio-based products for developing a bio-based economy.

Lignocellulosic nanofibrils produced using wheat straw and their pulping solid residue: From agricultural waste to cellulose nanomaterials

Each year millions of tons of agricultural wastes are produced, however, not well utilized in China. Considering the economic development and environmental protection, the valorization of these wastes is increasingly necessary and important. Here we used p-toluenesulfonic acid hydrolysis followed by mild disk grinding for on-farm valorization of wheat straw (WS) and their pulping solid residue (waste wheat straw, WWS) to produce lignocellulosic nanofibrils (LCNF). Alkaline peroxide post-treatment was further conducted to obtain purified lignocellulosic nanofibrils (P-LCNF) with lower lignin content and thinner diameters. The raw materials and resulting LCNF and P-LCNF were investigated in each process for their chemical component, crystal structure, morphology, and thermal properties. Interestingly, although WS fiber had higher lignin content than WWS fiber, the WS fiber with lower ash content resulted in LCNF and P-LCNF with smaller height and lower thermal stability, but higher crystallinity and higher specific surface area. Higher ash content in WWS fiber protected cellulose and lignin from depolymerization and degradation, respectively, which endowed LCNF and P-LCNF with entangled network structure. Overall, this study indicated that the low-temperature fractionation process on WS and WWS fibers could yield cellulose nanomaterials with potential value-added application and achieve the efficient utilization of agricultural wastes.

Enhancement of Hydrotropic Fractionation of Poplar Wood using Autohydrolysis and Disk Refining Pretreatment: Morphology and Overall Chemical Characterization

Solid acids have been proposed as a hydrolytic agent for wood biomass dissolution. In this work, we presented an environmentally friendly physicochemical treatment to leave behind cellulose, dissolve hemicellulose, and remove lignin from poplar wood. Several pretreatments, such as autohydrolysis and disk refining, were compared to optimize and modify the process. The p-toluenesulfonic acid could extract lignin from wood with a small amount of cellulose degradation. Disk refining with subsequent acid hydrolysis (so-called physicochemical treatment) doubled the delignification efficiency. A comprehensive morphology and overall chemical composition were provided. The crystallinity index (CrI) of treated poplar was increased and the chemical structure was changed after physicochemical treatment. Optical microscopy and scanning electron microscopy analysis demonstrated physicochemical treatment affected the morphology of poplar wood by removing lignin and generating fiberization. In general, this work demonstrated this physicochemical method could be a promising fractionation technology for lignocellulosic biomass due to its advantages, such as good selectivity, in removing lignin while preserving cellulose.