Influence of Various Climatic Conditions on the Structural Changes of Semicrystalline PLA Spun-Bonded Mulching Nonwovens during Outdoor Composting

Application of poly(L-lactic acid)-based films for equilibrium modified atmosphere packaging of "Kyoho" grapes and its favorable protection for anthocyanins

Grapes were packaged by different Poly (L-lactic acid)-based packaging films (PLTL-PLEL) and stored at 5 °C for 35 days to investigate the effects of equilibrium modified atmosphere packaging on the quality of "Kyoho" grapes during storage. Changes in physiochemical quality, antioxidant content and senescence of grapes were studied. Furthermore, UPLC-Q-TOF-MS/MS was used to observe and identify key factors influencing the variation of grape anthocyanins under different atmosphere conditions. Alterations in gas components and enzyme activities significantly impacted anthocyanin levels, highlighting oxygen concentration as the primary influence on total anthocyanin levels. The PLTL-PLEL50 packaging resulted in an approximate 5.7% lower weight loss and increased soluble solids by approximately 14.4%, vitamin C, total phenols and flavonoids reaching 60.2 mg/100 g, 8.4 mg/100 g and 7.2 mg/100 g, respectively. This packaging also preserved higher anthocyanin levels, with malvidin-3-glucoside and peonidin-3-glucoside at 0.55 μg/mL and 1.62 μg/mL, respectively, on the 35th day of storage.

Degradation of Biodegradable Nonwoven Mulches in the Winter Period

An open field experiment from November 2022 to May 2023 in Croatia, which is characterized by a continental humid climate, evaluated nonwoven mulches made from viscose, jute, and hemp fibres blended with PLA fibres. The blends of viscose and jute fibres (90:10, 80:20, and 70:30 ratios) were produced using mechanical web formation on cards with needle punching for bonding webs. Additionally, hemp fibres were blended with PLA fibres in a ratio of 80:20. Winter conditions caused significant structural changes in the mulches, including shrinkage, increased mass per unit area, thickness, and reduced air permeability. The amount of PLA fibre in the nonwoven mulch blends significantly affected nonwoven fabric structure change during exposure to winter conditions. After 180 days, the breaking force of all mulches increased by 30% to 277%. The soil beneath jute and hemp mulches maintained higher temperatures and moisture levels compared to viscose mulches. Soil organic carbon content varied with fibre type and was higher under jute and hemp mulches. K2O content was significantly higher in soils covered by mulches. All mulches effectively suppressed weeds. The experiment results showed that the newly produced nonwoven mulches could replace the conventional agro foil. Results also suggest that choosing biodegradable nonwoven mulches produced from fibres obtained from natural and renewable sources can influence soil fertility and the availability of nutrients, ultimately affecting plant growth and agricultural productivity.

Design and optimization methodology for different 3D processed materials (PLA, ABS and carbon fiber reinforced nylon PA12) subjected to static and dynamic loads

This research presents a methodology for the design and optimization of 3D printed parts with material extrusion (MEX) technology with three different commercial materials: PLA, ABS and N + CF (PA12) subjected to tensile and fatigue stresses, which included three stages: pretreatment, design of experiments and sequential optimization by statistical modeling. In the pretreatment stage, mainly the printing control factors (inner layer and contour height, printing speed, extrusion temperature, nozzle, infill arrangement and printing orientation) were determined; then, factors to optimize tensile strength as a function of printing pattern (linear, 3D, hexagonal), infill percentage (33%, 66%, 100°) and printing orientation (+45°/-45°, 0°/90°) were evaluated. Fatigue analysis was performed as a function of impression orientation using 100% infill, linear impression pattern, 5 Hz and a load range between 90 and 50% UTS. Optimization of tensile strength resulted in parts that exceeded the UTS of their corresponding filament, leading to infinite life relative to fatigue tests. Results were presented for fatigue life prediction based on Weibull analysis, Basquińs model and a multivariate response surface correlation analysis. The best fatigue behavior was related to the optimized tensile strength, the infill pattern applied to the printing orientation and the intrinsic properties of ABS (1 × 107cycles, stress up to 20 MPa). With respect to the other materials, a good fatigue behavior was highlighted at the number of cycles achieved 1 × 106 (stress up to 18 MPa) and 1 × 105 (stress up to 24 MPa) for N + CF and PLA, respectively. This study contributes to a better understanding of how printing parameters correlate with tensile and fatigue properties.

Effects of Melt-Blown Processing Conditions on Nonwoven Polylactic Acid and Polybutylene Succinate

This research aimed to prepare nonwovens from polylactic acid and polybutylene succinate using the melt-blown process while varying the melt-blown process parameters, including air pressure (0.2 and 0.4 MPa) and die-to-collector distance (15, 30, and 45 cm). Increasing the air pressure and die-to-collector distance resulted in the production of smaller fibers. Simultaneously, the tensile strength was dependent on the polymer, air pressure, and die-to-collector distance used, and the percentage elongation at the break tended to increase with an increasing die-to-collector distance. Regarding thermal properties, the PBS nonwovens exhibited an increased level of crystallinity when the die-to-collector distance was raised, consistent with the degree of crystallinity obtained from X-ray diffraction analysis. Polylactic acid could be successfully processed into nonwovens under all six investigated conditions, whereas nonwoven polybutylene succinate could not be formed at a die-to-collector distance of 15 cm. However, both polymers demonstrated the feasibility of being processed into nonwovens using the melt-blown technique, showing potential for applications in the textile industry.

Applications of Novel Biodegradable Polymeric Materials

Commonly used traditional polymeric materials have many advantages, although their resistance to biological agents causes a negative impact on the environment [...].

Biodegradable Nonwoven Agrotextile and Films—A Review

As society becomes more aware of environmental pollution, global warming, and environmental disasters, people are increasingly turning to sustainable materials and products. This includes agrotextiles in a wide range of products, including nonwoven agrotextiles for mulching. This review provides insight into relevant available data and information on the condition, possibilities, and trends of nonwoven mulches from natural fibres, biopolymers, and recycled sources. The basic definitions and differences between biodegradation and composting processes are explained, and the current standards related to biodegradation are presented. In addition, an insight into the biodegradation of various nonwoven mulches and films, including their advantages and disadvantages, is provided, to predict the future directions of nonwoven mulches development.

Modification and Properties of Cellulose Nonwoven Fabric-Multifunctional Mulching Material for Agricultural Applications

The paper describes a method of modifying a commercial viscose nonwoven fabric and its use as a modern mulching material in agriculture. The conducted research confirmed that the proposed modification of the viscose nonwoven fabric could be successfully used as a multipurpose and, above all, completely biodegradable nonwoven crop cover, which will eliminate the problem of disposal after the harvest period. Modified cellulose nonwoven fabric was obtained by staining with NB—BT helion brown, then padding with potassium nitrate (KNO₃) solution (used as a fertilizer) and finally coating with polylactide (PLA) solution. The characterisation of the nonwoven fabric included structural analysis, physicochemical properties and mechanical tests. The modified cellulose nonwovens were used in the tunnel cultivation of tomatoes as a heat-retardant, water-absorbing, antiweed mulching material that prevents soil infestation and slowly releases fertilizers.

Investigation of the Influence of PLA Molecular and Supramolecular Structure on the Kinetics of Thermal-Supported Hydrolytic Degradation of Wet Spinning Fibres

In this study, differences in the kinetics of the thermal-supported hydrolytic degradation of polylactide (PLA) wet spinning fibres due to material variance in the initial molecular and supramolecular structure were analysed. The investigation was carried out at the microstructural and molecular levels by using readily available methods such as scanning electron microscopy, mass erosion measurement and estimation of intrinsic viscosity. The results show a varying degree of influence of the initial structure on the degradation rate of the studied PLA fibres. The experiment shows that hydrolytic degradation at a temperature close to the cold crystallization temperature is, on a macroscopic level, definitely more rapid for the amorphous material, while on a molecular scale it is similar to a semi-crystalline material. Furthermore, for the adopted degradation temperature of 90 °C, a marginal influence of the pH of the degradation medium on the degradation kinetics was also demonstrated.

Improving the Thermal and Mechanical Properties of Poly(l-lactide) by Forming Nanocomposites with an in Situ Ring-Opening Intermediate of Poly(l-lactide) and Polyhedral Oligomeric Silsesquioxane

In this study, a series of poly(l-lactide) and (3-amino)-propylheptaisobutyl cage silsesquioxane (PLLA-AMPOSS) intermediates were first fabricated using single-arm in situ solution polymerization of LLA monomers and AMPOSS nanoparticles with different contents, 0.02-1.00 mol%. Then, the PLLA-AMPOSS intermediate with 0.5 mol% AMPOSS was selected as a representative and investigated by nuclear magnetic resonance (NMR) and X-ray diffraction (XRD). Afterwards, it was added into the pure PLLA with different mass fractions. Finally, the thermal behavior, crystallization kinetics, morphological characteristics, and mechanical properties of the obtained PLLA/PLLA-AMPOSS nanocomposites were carefully measured and investigated by differential scanning calorimetry (DSC), polarizing microscopy (POM), scanning electron microscopy (SEM), and tensile test. After comparing the PLLA-AMPOSS intermediate and PLLA/AMPOSS blend, the results show that the ring-open polymerization of PLLA-AMPOSS intermediate was successful. The results also show that the existence of PLLA-AMPOSS has a strong influence on the crystallization behavior of PLLA/PLLA-AMPOSS composites, which can be attributed to the heterogeneous nucleation effect of PLLA-AMPOSS. In addition, it was also found from the tensile test results that the addition of the PLLA-AMPOSS nanofiller improved the tensile strength and strain at break of PLLA/PLLA-AMPOSS nanocomposites. All of these results indicate the good nucleating effect of PLLA-AMPOSS and that the AMPOSS disperses well in the PLLA/PLLA-AMPOSS nanocomposites. A conclusion can be drawn that the selective nucleating agent and the combined method of in situ ring-opening polymerization and physical blending are feasible and effective.