Synthesis and Properties of In-Situ Bulk High Impact Polystyrene Toughened by High cis-1,4 Polybutadiene

Morphology and Thermodynamic Study of a Novel Composite Membrane from Waste Polystyrene/Slag: Experimental Investigation

The development of the membrane surface and cross-sectional morphology is pivotal in influencing the effectiveness of membrane separation. In this study, evaluating the separation rates between the solvent and nonsolvent in the casting solution and the related thermodynamic alteration analysis were illustrated. Additionally, the rheological variations were determined by measuring the viscosity of the resulting dope solutions, providing an initial estimation of the phase separation kinetics. Asymmetric polystyrene (PS)/slag composite membrane, incorporating slag waste as an inorganic additive, was developed. Dimethylformamide (DMF) was utilized as the solvent, and sodium dodecyl sulfate (SDS) was employed as an anionic surfactant to facilitate the casting process. A tertiary system diagram approach involving waste PS, DMF, and water introducing slag as an inorganic additive and SDS as a surfactant was attained to promote the separation of the solvent and nonsolvent in the casting solution. These novel composite mixtures exhibited increased thermodynamic instability within the coagulation bath, facilitating the rapid separation of solid membranes from the dope solutions and forming composite membranes with significantly increased porosity (exceeding a 20% increase) compared to that of plain waste materials. The composite membrane characteristics were assessed with the widely used poly(vinylidene difluoride) (PVDF) membrane, showing comparative features and performance when tested on a membrane distillation (MD) cell; it gave a flux of 1 kg/m2·h. These promising characteristics positioned this novel PS/slag composite membrane as a candidate for various water-related applications.

Influence of Biogenic Material Content on the Biodegradability of Styrene-Butadiene Composites with Incorporated Chlorella vulgaris Biomass

Bio-fillers are intensively studied for advanced polymer composite circular design and production. In this context, the algal biomass may be considered an important and relatively low-cost resource, when harvested as a by-product from wastewater treatment plants. The biomass of the algal species Chlorella vulgaris is frequently used in this type of environmental process, and its macro constituents' composition ranges from around 15-25% carbohydrates, 10-20% lipids, and 50-60% proteins. Poly (styrene-butadiene-styrene) (SBS) copolymers have a matrix composed of glassy polystyrene domains connected by flexible polybutadiene segments. Although the physical-mechanical properties of SBS copolymers recommend them for many industrial applications, they have the drawback of low biodegradability. This study aimed to assess the aerobic biodegradability of polymer composites by integrating biomass from Chlorella vulgaris at varying mass percentages of 5, 10, and 20% into SBS copolymer composites. Biodegradation tests were conducted under industrial composting conditions (58 °C and 50% relative humidity) for 180 days. The biodegradability of materials was evaluated by measuring the CO2 produced in each vessel during the study period. Potential correlations between the amount of carbon dioxide released and the percentage of biomass added to the polymer matrix were examined. Structural and morphological changes were assessed using Fourier Transform infrared spectroscopy (FTIR), thermal analysis (DSC), and scanning electron microscopy (SEM). Physical and chemical testing revealed a decrease in sample density after the industrial composting test, along with noticeable changes in melt flow index (MFI). The observed physical and chemical changes, coupled with FTIR, SEM, and DSC data, indicate increased cross-linking and higher porosity in biodegraded polymer structures with higher biomass content. This behavior is likely due to the formation of cross-linked connections between polymer chains and polypeptide chains resulting from protein degradation, enhancing connections between polystyrene units facilitated by peptide bonds with the benzene units of the styrene blocks within the polymer matrix.

Biodegradation Study of Styrene-Butadiene Composites with Incorporated Arthrospira platensis Biomass

The preparation of polymer composites that incorporate material of a biogenic nature in the polymer matrices may lead to a reduction in fossil polymer consumption and a potentially higher biodegradability. Furthermore, microalgae biomass as biogenic filler has the advantage of fast growth and high tolerance to different types of culture media with higher production yields than those provided by the biomass of terrestrial crops. On the other hand, algal biomass can be a secondary product in wastewater treatment processes. For the present study, an SBS polymer composite (SBSC) containing 25% (w/w) copolymer SBS1 (linear copolymer: 30% styrene and 70% butadiene), 50% (w/w) copolymer SBS2 (linear copolymer: 40% styrene and 60% butadiene), and 25% (w/w) paraffin oil was prepared. Arthrospira platensis biomass (moisture content 6.0 ± 0.5%) was incorporated into the SBSC in 5, 10, 20, and 30% (w/w) ratios to obtain polymer composites with spirulina biomass. For the biodegradation studies, the ISO 14855-1:2012(E) standard was applied, with slight changes, as per the specificity of our experiments. The degradation of the studied materials was followed by quantitatively monitoring the CO2 resulting from the degradation process and captured by absorption in NaOH solution 0.5 mol/L. The structural and morphological changes induced by the industrial composting test on the materials were followed by physical-mechanical, FTIR, SEM, and DSC analysis. The obtained results were compared to create a picture of the material transformation during the composting period. Thus, the collected data indicate two biodegradation processes, of the polymer and the biomass, which take place at the same time at different rates, which influence each other. On the other hand, it is found that the material becomes less ordered, with a sponge-like morphology; the increase in the percentage of biomass leads to an advanced degree of degradation of the material. The FTIR analysis data suggest the possibility of the formation of peptide bonds between the aromatic nuclei in the styrene block and the molecular residues resulting from biomass biodegradation. It seems that in industrial composting conditions, the area of the polystyrene blocks from the SBS-based composite is preferentially transformed in the process.

Hydrophobic, Thermal Shock-and-Corrosion-Resistant XSBR Latex-Modified Lightweight Class G Cement Composites in Geothermal Well Energy Storage Systems

Energy losses can be significantly reduced if thermally insulating cement is used for energy storage and recovery. The thermal conductivity (TC) of the currently used cement is between 1 and 1.2 W/mK. In this study we assessed the ability of polystyrene (PS)-polybutadiene (PB)-polyacrylic acid (PAA) terpolymer (cross-linked styrene-butadiene rubber, XSBR) latex to improve thermal insulating properties and thermal shock (TS) resistance of class G ordinary Portland cement (OPC) and fly ash cenosphere (FCSs) composites in the temperature range of 100-175 °C. The composites autoclaved at 100 °C were subjected to three cycles, one cycle: 175 °C heat → 25 °C water quenching). In hydrothermal and thermal (TS) environments at elevated temperatures in cement slurries the XSBR latex formed acrylic calcium complexes through acid-base reactions, and the number of such complexes increased at higher temperatures due to the XSBR degradation with formation of additional acrylic groups. As a result, these complexes offered the following five advanced properties to the OPC-based composites: (1) enhanced hydrophobicity; (2) decreased water-fillable porosity; (3) reduced TC for water-saturated composites; (4) minimized loss of compressive strength, Young's modulus, and compressive fracture toughness after TS; and (5) abated pozzolanic activity of FCSs, which allowed FCSs to persist as thermal insulators under strongly alkaline conditions of cement slurries. Additionally, XSBR-modified slurries possessed improved workability and decreased slurry density due to the air-entraining effect of latex, which resulted in further improvement of thermal insulation performance of the modified composites.

Heteroaggregation of virions and microplastics reduces the number of active bacteriophages in aqueous environments

The objective of this study is to explore the effects of microplastics on the viability of the bacteriophages in an aqueous environment. Bacteriophages (phages), that is, viruses of bacteria, are essential in homeostasis. It is estimated that phages cause up to 40% of the death of all bacteria daily. Any factor affecting phage activity is vital for the whole food chain and the ecology of numerous niches. We hypothesize that the number of active phages decreases due to the virions' adsorption on microplastic particles or by the released leachables from additives used in the production of plastic, for example, stabilizers, plasticizers, colorants, and reinforcements. We exposed three diverse phages, namely, T4 (tailed), MS2 (icosahedral), and M13 (filamentous), to 1 mg/mL suspension of 12 industrial-grade plastics [acrylonitrile butadiene styrene, high-impact polystyrene, poly-ε-caproamide, polycarbonate, polyethylene, polyethylene terephthalate, poly(methyl methacrylate), polypropylene, polystyrene, polytetrafluoroethylene, polyurethane, and polyvinyl chloride] shredded to obtain microparticles of radius ranging from 2 to 50 μm. The effect of leachables was measured upon exposure of phages not to particles themselves but to the buffer preincubated with microplastics. A double-overlay plaque counting method was used to assess phage titers. We employed a classical linear regression model to verify which physicochemical parameters (65 variables were tested) govern the decrease of phage titers. The key finding is that adsorption mechanisms result in up to complete scavenging of virions, whereas leachables deactivate up to 50% of phages. This study reveals microplastic pollution's plausible and unforeseen ecotoxicological effect causing phage deactivation. Moreover, phage transmission through adsorption can alter the balance of the food chain in the new environment. The effect depends mainly on the zeta potentials of the polymers and the phage type.

Simultaneous determination of additive concentration in rubber using ATR-FTIR spectroscopy

Using attenuated total reflection (ATR) Fourier transform infrared (FTIR) spectroscopy for direct quantitative analysis is highly desirable for many sample systems due to advantages such as rapid spectra collection and being completely non-destructive. However, for many complex sample matrices the feasibility of direct quantitative analysis using ATR-FTIR is uncertain. The commonly used Beer-Lambert law may not be applicable for many systems in general, besides sample related complexities such as inhomogeneity, variable optical properties, or heavily overlapping absorption bands. In this study, we consider fully formulated vulcanized rubber with carbon black or silica as the primary filler as our system of interest. We developed a method to simultaneously quantify the concentration of three different antidegradents of similar chemical structure directly on rubber samples using ATR-FTIR spectra. Results show that absorbance follows the Beer-Lambert law well for the range of antidegradent concentrations considered. Despite this, a direct application of the Beer-Lambert law to deconvolute overlapping peaks between antidegradents proved insufficient. Through the application of partial least squares (PLS) multivariate analysis, remarkable prediction accuracy of within about 0.15 wt% error for all three antidegradents was achieved for both types of rubber formulations, even with high levels of carbon black. These results show the value this method has for quantitative analysis of additives in rubber. Our investigation highlights the potential usefulness of FTIR spectroscopy in general for rapid quantitative analysis directly on samples of interest without any prior chemical separation.

Cavitation-Mediated Fracture Energy Dissipation in Polylactide at Rubbery Soybean Oil-Based Block Copolymer Interfaces Formed via Reactive Extrusion

Here, we spearhead a new approach to biopolymer impact modification that demonstrates superior performance while maintaining greater than 99% compostability. Using soybean-based monomers, a virtually untapped resource in terms of commercial volume and overall cost, a series of hyperbranched block copolymers were synthesized and melt-processed with poly(l-lactide) (PLA) to yield impact resistant all-polymer composites. Although PLA impact modification has been treated extensively, to date, the only practical solutions have relied on non-compostable petroleum-based rubbers. This study illustrates the activity of energy dissipation mechanisms such as cavitation, classically relegated to well-entangled petroleum-based rubbers, in poorly entangled hyperbranched soybean-based rubbers. Furthermore, we present a complete study of the mechanical performance and morphology of these impact modified PLA composites. The significance of combining deformation theory with a scalable green alternative to petroleum-based rubbers opens up a potential avenue for cheap compostable engineering thermoplastics.

High-Impact Polystyrene Reinforced with Reduced Graphene Oxide as a Filament for Fused Filament Fabrication 3D Printing

Graphene and its derivatives, such as graphene oxide (GO) or reduced graphene oxide (rGO), due to their properties, have been enjoying great interest for over two decades, particularly in the context of additive manufacturing (AM) applications in recent years. High-impact polystyrene (HIPS) is a polymer used in 3D printing technology due to its high dimensional stability, low cost, and ease of processing. However, the ongoing development of AM creates the need to produce modern feedstock materials with better properties and functionality. This can be achieved by introducing reduced graphene oxide into the polymer matrix. In this study, printable composite filaments were prepared and characterized in terms of morphology and thermal and mechanical properties. Among the obtained HIPS/rGO composites, the filament containing 0.5 wt% of reduced graphene oxide had the best mechanical properties. Its tensile strength increased from 19.84 to 22.45 MPa, for pure HIPS and HIPS-0.5, respectively. Furthermore, when using the HIPS-0.5 filament in the printing process, no clogging of the nozzle was observed, which may indicate good dispersion of the rGO in the polymer matrix.

Double-Function Oxygen Scavenger and Aromatic Food Packaging Films Based on LDPE/Polybutadiene and Peanut Aroma

The aim of this study was to develop a double function active packaging material for nuts. The packaging solution, on the one hand, integrated polybutadiene (PB) as an oxygen scavenger and, on the other hand, it incorporated peanut aroma (PA) to improve customer’s sensorial experience. Different formulations based on low density polyethylene (LDPE), commercial PA (5 wt %) and PB at two levels (5 wt % and 13 wt %) were obtained by cast film extrusion. The obtained films were compared in terms of their mechanical, structural, optical and thermal properties confirming a plasticizing effect of PA and PB resulting in an increase in the ductility of the polymer and in a slight decrease in the thermal properties, maintaining their transparency. Regarding the oxygen capacity of the films, values of 4.4 mL and 2.7 mL O₂ g⁻¹ film were obtained for PE/PA/PB13 and PE/PA/PB5, respectively, after 6 days proving the suitability of the UV irradiation treatment in improving the oxygen absorption capacity of PB without the need of a metal catalyst. The aroma retention capacity into the polymer matrix was also evaluated in the developed formulations. The incorporation of PB in 13 wt % into a LDPE matrix improved the PA retention. This behavior was attributed to the ability of PB in enhancing cross-linking of LDPE as the concentration of PB increases. The results suggested the potential of PE/PB/PB13 films as oxygen scavenger and aromatic food packaging system to offer protection against lipid oxidation in nuts.

Analysis of Thermomechanical Properties of Selected Class of Recycled Thermoplastic Materials Based on Their Applications

Polypropylene and polystyrene are petroleum-based thermoplastics which are commonly used and disposed of in the environment after their service life, leading to environmental degradation. There is a need to recycle polypropylene and polystyrene, but the effect of recycling on thermo-mechanical properties is not well understood. This study aims to determine thermo-mechanical properties of the recycled polypropylene and recycled polystyrene and compare them with corresponding virgin polypropylene and newly produced polystyrene (general purpose polystyrene 1540 and high impact polystyrene 7240). The study was carried out by preparing bar-shaped samples of recycled polypropylene, recycled polystyrene, general purpose polystyrene 1540, and high impact polystyrene 7240 by compression molding using a hot press and thermally characterizing them to determine glass transition temperature and melting temperature using differential scanning calorimetry. The changes in Young’s modulus, tensile strength, hardness, and toughness due to recycling activities were determined at room temperature (24 °C), 40 °C, 60 °C, and 80 °C. The thermo-mechanical properties of recycled polystyrene (PS) were found to be comparable to those of high impact polystyrene (HIPS) 7240. The study revealed that the hardness and toughness for the recycled polymers were higher than those of corresponding virgin polymers. On the other hand, tensile strength and Young’s modulus for the recycled polymers were lower than those of the virgin polymers. Understanding the thermo-mechanical properties of the recycled polymers will contribute to more industrial applications hence increase the rate of recycling, resulting in a reduction in environmental pollution.