Novel Method for the Manufacture of Complex CFRP Parts Using FDM-based Molds

The Influence of Selected Fillers on the Functional Properties of Polycarbonate Dedicated to 3D Printing Applications

Additive manufacturing is still the fastest-developing technology in the modern world. Three-dimensional printing has become popular due to the method's numerous advantages, such as its short time and low cost, compared to conventional methods such as injection molding. Therefore, the demand for new materials and material systems that will be characterized by the desired functional properties is clearly growing. As part of this work, work was carried out on the development and preparation of new polymer composites dedicated to 3D printing applications, especially in FDM/FFF/MEM technologies. The influence of the content and amount of fillers, such as silica modified with alumina (S) and bentonite modified with a quaternary ammonium salt (B), on the functional properties of a commercially available fiber made of traditional plastic, such as polycarbonate, obtained in the form of a filament (PCF), was determined. It was found that the addition of B significantly increased the fluidity of the polymer, the introduction of a filler in the amount of 1.5% allowed to obtain a result that was 6% higher compared to PCF (16.8 g/10 min), while the amount of 3% was 20% higher. The obtained mass melt flow rate (MFR) results were confirmed by determining the viscosity of the produced polymer composites. Satisfactory results of mechanical properties were obtained, including the following: it was found that the introduced modified fillers increased the elasticity of the material. The introduction of modified silica resulted in a reduction in Young's modulus by 10.02% at the content of 0.5% S and at 1% S by 8.64% compared to the polymer. The introduced modified filler S significantly increased the thermostability of polycarbonate (T5% equal to 449 °C) by 23 °C for PCF/0.5% S and 14 °C for PCF/1% S, respectively. The SEM and WAXS results confirmed the appropriate dispersion of the fillers in the polymer matrix, which indicates well-selected conditions for the homogenization process of the components and the subsequent production of samples. Detailed characterization of the influence of selected fillers on the functional properties of the polymer matrix-polycarbonate allowed for an increase in the range of polymer composites and their use in rapid prototyping technologies, as well as supplementing the literature on databases regarding the characteristics of the obtained materials.

Influence of the Resin System and Sand Type on the Infiltration of 3D-Printed Sand Tools

Binder jetting is a highly productive additive manufacturing (AM) method for porous parts. Due to its cost-effectiveness, it is used for large components and quantities ranging from prototyping to series production. Post-processing steps like sintering or infiltration are common in several applications to achieve high density and strength. This work investigates how 3D-printed sand molds can be infiltrated with epoxy resins without vacuum assistance to produce high-strength molds for thermoforming applications. Specimens 3D-printed from different sand types are infiltrated with resins of different viscosity and analyzed for infiltration velocity and depth. The infiltration velocities corresponded well with the correlation described in Washburn's equation: The resins' viscosities and the saturation level were decisive. Amongst the investigated sand types commonly used in foundries, sand type GS19 was found most suitable for infiltration. However, the sand type proved to be a less relevant influencing factor than the resins' viscosities and quantities applied. Infiltration of topology-optimized 3D-printed sand tools up to a wall thickness of 20 mm for thermoforming applications was found to be feasible.

Tribo-Mechanical Investigation of Glass Fiber Reinforced Polymer Composites under Dry Conditions

Tribo-mechanical experiments were performed on Glass Fiber Reinforced Polymer (GRFP) composites against different engineering materials, and the tribological behavior of these materials under dry conditions was investigated. The novelty of this study consists of the investigation of the tribomechanical properties of a customized GFRP/epoxy composite, different from those identified in the literature. The investigated material in the work is composed of 270 g/m² fiberglass twill fabric/epoxy matrix. It was manufactured by the vacuum bag method and autoclave curing procedure. The goal was to define the tribo-mechanical characteristics of a 68.5% weight fraction ratio (wf) of GFRP composites in relation to the different categories of plastic materials, alloyed steel, and technical ceramics. The properties of the material, including ultimate tensile strength, Young's modulus of elasticity, elastic strain, and impact strength of the GFPR, were determined through standard tests. The friction coefficients were obtained using a modified pin-on-disc tribometer using sliding speeds ranging from 0.1 to 0.36 m s^-1, load 20 N, and different counter face balls from Polytetrafluoroethylene (PTFE), Polyamide (Torlon), 52,100 Chrome Alloy Steel, 440 Stainless Steel, and Ceramic Al₂O₃, with 12.7 mm in diameter, in dry conditions. These are commonly used as ball and roller bearings in industry and for a variety of automotive applications. To evaluate the wear mechanisms, the worm surfaces were examined and investigated by a Nano Focus-Optical 3D Microscopy, which uses cutting-edge μsurf technology to provide highly accurate 3D measurements of surfaces. The obtained results constitute an important database for the tribo-mechanical behavior of this engineering GFRP composite material.

Polymer Composites Based on Polycarbonate/Acrylonitrile-Butadiene-Styrene Used in Rapid Prototyping Technology

As part of this work, polymer composites based on polycarbonate/acrylonitrile-butadiene-styrene (PC/ABS) were obtained and used in 3D printing technology, particularly Melted Extrusion Modeling (MEM) technology. The influence of selected fillers on the properties of the obtained composites was investigated. For this purpose, modified fillers such as silica modified with alumina, bentonite modified with a quaternary ammonium salt, and hybrid lignin/silicon dioxide filler were introduced into the PC/ABS matrix. In the first part of this work, polymer blends and their composites containing 1.5-3 wt. of the filler were used to obtain the filament using the proprietary technological line. Moldings for testing the performance properties were obtained using additive manufacturing techniques and injection molding. In the subsequent part of this work, rheological properties (mass flow rate (MFR) and viscosity curves) and mechanical properties (Rockwell hardness and static tensile strength with Young's modulus) were examined. The structures of the obtained composites were also determined by scanning electron microscopy (SEM/EDS). The obtained results confirmed the results obtained from a wide-angle X-ray scattering analysis (WAXS). In turn, the physicochemical properties were characterized on the basis of the results of tests using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Based on the obtained results, it was found that the introduced modified additives had a significant impact on the processing and functional properties of the tested composites.

Hybrid Polymer Composites Based on Polystyrene (PS) Used in the Melted and Extruded Manufacturing Technology

As part of the work, innovative hybrid polymer composites dedicated to rapid prototyping, especially for 3D printing with the melted and extruded manufacturing (MEM) technique, were developed. For this purpose, the influence of modified fillers, such as alumina-modified silica, bentonite modified with quaternary ammonium salt, and lignin/silicon dioxide hybrid filler, on the functional properties of polystyrene-based composites was investigated. The introduced additives were selected to improve the processing properties of polystyrene (PS), in particular its thermal stability, while maintaining good mechanical properties. In the first part of the work, using the proprietary technological line, filaments from unfilled PS and its composites were obtained, which contain modified fillers in the amount of 1.5% to 3.0% by weight. Samples for testing functional properties were obtained by 3D printing in MEM technology and injection technique. The rheological properties-mass melt flow rate (MFR), viscosity, and mechanical properties-are presented in the further part of the work. The size and the respective dispersion in the polystyrene polymer matrix of the fillers used were determined by scanning electron microscopy with energy dispersion spectroscopy (SEM/EDS). The correct dispersion of additives in PS was also confirmed by wide-angle X-ray analysis (WAXS). A significant improvement in the thermal stability of the obtained composites after the introduction of fillers into the polymer matrix was confirmed on the basis of thermogravimetric analysis (TGA). The remaining tests of physicochemical properties, differential scanning calorimetry (DSC), and infrared spectroscopy with Fourier transform (FT-IR) allowed us to state no significant changes in relation to polystyrene. The obtained test results allowed us to conclude that the amount and type of fillers used in the PS polymer matrix significantly affect the performance properties of the tested hybrid composites. The composites obtained as part of the work can be successfully used in rapid prototyping technologies, especially for the production of details originally designed from PS, which are required to have higher thermal stability than is guaranteed only by the polymer matrix.

Production readiness assessment of low cost, multi-material, polymeric 3D printed moulds

Fused Deposition Modelling (FDM) technology allows to choose a large variety of materials and it is widely used by companies and individuals nowadays. The cost effectiveness of rapid prototyping is achievable via FDM, that makes this technology useful for research and innovation. The application of 3D printing to aid production is the most common approach. Moreover, the use of 3D printing in prototypes result in a waste of material since no reuse is considered. In the following manuscript, this technology is applied to mould fabrication by achieving a low surface roughness at a modest cost compared to conventional manufacturing methods. Moreover, the possibility to use a combination of thermoplastic materials is analysed by examination of the CAD model optimized for Additive Manufacturing (AM) from scratch and was verified using metrology tools. Several moulds were finally built and applied to the specific case study of carbon fibre laminated components. This manuscript aims to analyse the manufacturing process by comparing the mould surface geometry before and after the smoothing process. The achieved tolerance between the produced moulds is ±0.05 mm that ensures the repeatability of the process from an industrial point of view; whilst the deviation between CAD and mould is ±0.2 mm. To combine an accurate FDM process together with chemical smoothing proved to be a powerful strategy to produce high quality components that can be inserted in the production process by means of traditional manufacturing techniques. This will aid to reduce the cost of standard manufacturing for low production batches and prototypes of carbon fibre composites.

•

The FDM AM procedure must be properly set up for the best outcome.

•

The new generation FDM AM machinery gives the opportunity to explore new opportunities to reach manufacturing process efficiency to widen the target of this technology.

•

Surface quality by FDM creation can be outstandingly improved with chemical smoothing process.

•

Quality control by means of 3D scanning proved to be efficient with detection resolution in the order of 0.01 mm.

A Set of Novel Procedures for Carbon Fiber Reinforcement on Complex Curved Surfaces Using Multi Axis Additive Manufacturing

There has been considerable research in recent years on the additive manufacturing (AM) of carbon fiber reinforced polymer (CFRP) parts based on the process of fused deposition modeling (FDM). The currently-applied steps within the manufacturing pipeline, such as slicing and path planning, consider only the planar case of filament deposition and mostly make no use of the possibility to place single pre-impregnated (prepreg) filaments. Classical methods such as tape-laying and laminating struggle with highly curved and complex geometries and require the costly production of molds, whereas when using AM, these geometries can be realized more easily and molds can be created using the same process. In this paper, a set of algorithms is presented that aims to resolve these problems. Criteria are formulated which enable the goal oriented development and evaluation of the presented methods and represent metrics for future methods. The developed algorithms enable the use of both continuous and discontinuous fiber patches in a much wider range of applications in designing and manufacturing of CFRPs. This opens up new possibilities in this promising field. The developed metrics and infrastructure further constitute progress in the field of multi-axis non-planar path planning for slicing algorithms in general and the conducted evaluation proves the formal applicability of the developed algorithms.

Polymer Composites Based on Glycol-Modified Poly(Ethylene Terephthalate) Applied to Additive Manufacturing Using Melted and Extruded Manufacturing Technology

As part of the work, innovative polymer composites dedicated to 3D printing applications were developed. For this purpose, the influence of modified fillers, such as silica modified with alumina, bentonite modified with quaternary ammonium salt, and hybrid filler lignin/silicon dioxide, on the functional properties of composites based on glycol-modified poly(ethylene terephthalate) (PET-G) was investigated. In the first part of the work, using the proprietary technological line, filaments from unfilled polymer and its composites were obtained, which contained modified fillers in an amount from 1.5% to 3.0% by weight. The fittings for the testing of functional properties were obtained using the 3D printing technique in the Melted and Extruded Manufacturing (MEM) technology and the injection molding technique. In a later part of the work, rheological properties such as mass melt flow rate (MFR) and viscosity, and mechanical properties such as Rockwell hardness, Charpy impact strength, and static tensile strength with Young's modulus were presented. The structure of the obtained composites was also described and determined using scanning electron microscopy with an attachment for the microanalysis of chemical composition (SEM/EDS) and the atomic force microscope (AFM). The correct dispersion of the fillers in the polymer matrix was confirmed by wide-angle X-ray scattering analysis (WAXS). In turn, the physicochemical properties were presented on the basis of the research results: thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FT-IR). On the basis of the obtained results, it was found that both the amount and the type of fillers used significantly affected the functional properties of the tested composites.

New Methodology for Evaluating Surface Quality of Experimental Aerodynamic Models Manufactured by Polymer Jetting Additive Manufacturing

The additive manufacturing (AM) applications have attracted a great deal of interest with regard to experimental aerodynamic studies. There is a need for a universal roughness scale that characterizes different materials used in aerodynamic research. The main purpose of this paper is identification of the potential of a material jetting AM process to produce accurate aerodynamic surfaces. A new methodology to evaluate the roughness of aerodynamic profiles (airfoils) was proposed. A very short-span wing artifact for preliminary tests and a long-span wing model were proposed for design of experiments. Different artifacts orientations were analyzed, maintaining the same surface quality on the upper and lower surface of the wing. A translucent polymeric resin was used for samples manufacturing by polymer jetting (PolyJet) technology. The effects of main factors on the surface roughness of the wing were investigated using the statistical design of experiments. Three interest locations, meaning the leading-edge, central, and trailing-edge zones, on the upper and lower surfaces of the airfoil were considered. The best results were obtained for a sample oriented at XY on the build platform, in matte finish type, with a mean Ra roughness in the range of 2 to 3.5 μm. Microscopy studies were performed to analyze and characterize the surfaces of the wing samples on their different zones.

Molds with Advanced Materials for Carbon Fiber Manufacturing with 3D Printing Technology

Fused Deposition Modeling (FDM) 3D printing is the most widespread technology in additive manufacturing worldwide that thanks to its low costs, finished component applications, and the production process of other parts. The need for lighter and higher-performance components has led to an increased usage of polymeric matrix composites in many fields ranging from automotive to aerospace. The molds used to manufacture these components are made with different technologies, depending on the number of pieces to be made. Usually, they are fiberglass molds with a thin layer of gelcoat to lower the surface roughness and obtain a smooth final surface of the component. Alternatively, they are made from metal, thus making a single carbon fiber prototype very expensive due to the mold build. Making the mold using FDM technology can be a smart solution to reduce costs, but due to the layer deposition process, the roughness is quite high. The surface can be improved by reducing the layer height, but it is still not possible to reach the same degree of surface finish of metallic or gelcoat molds without the use of fillers. Thermoplastic polymers, also used in the FDM process, are generally soluble in specific solvents. This aspect can be exploited to perform chemical smoothing of the external surface of a component. The combination of FDM and chemical smoothing can be a solution to produce low-cost molds with a very good surface finish.

3D Printed Sand Tools for Thermoforming Applications of Carbon Fiber Reinforced Composites-A Perspective

Tooling, especially for prototyping or small series, may prove to be very costly. Further, prototyping of fiber reinforced thermoplastic shell structures may rely on time-consuming manual efforts. This perspective paper discusses the idea of fabricating tools at reduced time and cost compared to conventional machining-based methods. The targeted tools are manufactured out of sand using the Binder Jetting process. These molds should fulfill the demands regarding flexural and compressive behavior while allowing for vacuum thermoforming of fiber reinforced thermoplastic sheets. The paper discusses the requirements and the challenges and presents a perspective study addressing this innovative idea. The authors present the idea for discussion in the additive manufacturing and FRP producing communities.

Polymer Composites Based on Polycarbonate (PC) Applied to Additive Manufacturing Using Melted and Extruded Manufacturing (MEM) Technology

As part of the present work, polymer composites used in 3D printing technology, especially in Melted and Extruded Manufacturing (MEM) technology, were obtained. The influence of modified fillers such as alumina modified silica, quaternary ammonium bentonite, lignin/silicon dioxide hybrid filler and unmodified multiwalled carbon nanotubes on the properties of polycarbonate (PC) composites was investigated. In the first part of the work, the polymer and its composites containing 0.5–3 wt.% filler were used to obtain a filament using the proprietary technological line. The moldings for testing functional properties were obtained with the use of 3D printing and injection molding techniques. In the next part of the work, the rheological properties—mass flow rate (MFR) and mechanical properties—Rockwell hardness, Charpy impact strength and static tensile strength with Young’s modulus were examined. The structure of the obtained composites was also described and determined using scanning electron microscopy (SEM). The porosity, roughness and dimensional stability of samples obtained by 3D printing were also determined. On the other hand, the physicochemical properties were presented on the basis of the research results using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), wide angle X-ray scattering analysis (WAXS) and Fourier Transform infrared spectroscopy (FT-IR). Additionally, the electrical conductivity of the obtained composites was investigated. On the basis of the obtained results, it was found that both the amount and the type of filler significantly affected the functional properties of the composites tested in the study.

Process-Structure-Properties in Polymer Additive Manufacturing

Additive manufacturing (AM) methods have grown and evolved rapidly in recent years [...].