Facile Synthesis of Ultrahigh Molecular Weight Poly(Methyl Methacrylate) by Organic Halides in the Presence of Palladium Nanoparticles

Development of Synthesis and Application of High Molecular Weight Poly(Methyl Methacrylate)

Poly(methyl methacrylate) (PMMA) is widely used in aviation, architecture, medical treatment, optical instruments and other fields because of its good transparency, chemical stability and electrical insulation. However, the application of PMMA largely depends on its physical properties. Mechanical properties such as tensile strength, fracture surface energy, shear modulus and Young’s modulus are increased with the increase in molecular weight. Consequently, it is of great significance to synthesize high molecular weight PMMA. In this article, we review the application of conventional free radical polymerization, atom transfer radical polymerization (ATRP) and coordination polymerization for preparing high molecular weight PMMA. The mechanisms of these polymerizations are discussed. In addition, applications of PMMA are also summarized.

Recent Progress of Metal Nanoparticle Catalysts for C–C Bond Forming Reactions

Over the past few decades, the use of transition metal nanoparticles (NPs) in catalysis has attracted much attention and their use in C–C bond forming reactions constitutes one of their most important applications. A huge variety of metal NPs, which have showed high catalytic activity for C–C bond forming reactions, have been developed up to now. Many kinds of stabilizers, such as inorganic materials, magnetically recoverable materials, porous materials, organic–inorganic composites, carbon materials, polymers, and surfactants have been utilized to develop metal NPs catalysts. This review classified and outlined the categories of metal NPs by the type of support.

PMMA Application in Piezo Actuation Jet for Dissipating Heat of Electronic Devices

The present study utilizes an acrylic (PMMA) plate with circular piezoelectric ceramics (PC) as an actuator to design and investigate five different types of piezo actuation jets (PAJs) with operating conditions. The results show that the heat transfer coefficient of a device of PAJ is 200% greater than that of a traditional rotary fan when PAJ is placed at the proper distance of 10 to 20 mm from the heat source, avoiding the suck back of surrounding fluids. The cooling effect of these five PAJs was calculated by employing the thermal analysis method and the convection thermal resistance of the optimal PAJ can be reduced by about 36%, while the voltage frequency, wind speed, and noise were all positively correlated. When the supplied piezoelectric frequency is 300 Hz, the decibel level of the noise is similar to that of a commercial rotary fan. The piezoelectric sheets had one of two diameters of 31 mm or 41 mm depending on the size of the tested PAJs. The power consumption of a single PAJ was less than 10% of that of a rotary fan. Among the five types of PAJ, the optimal one has the characteristics that the diameter of the piezoelectric sheet is 41 mm, the piezoelectric spacing is 2 mm, and the length of the opening is 4 mm. Furthermore, the optimal operating conditions are a voltage frequency of 300 Hz and a placement distance of 20 mm in the present study.

Chloroaluminate Gel Electrolytes Prepared with Copolymers Based on Imidazolium Ionic Liquids and Deep Eutectic Solvent AlCl3:Urea

Polymer gel electrolytes (PGEs) have been prepared with copolymers based on imidazolium ionic liquids and the deep eutectic mixture of AlCl₃:urea (uralumina) as liquid electrolyte. The copolymers were synthesized by photopolymerization of vinylpirrolidone or methylmethacrylate with imidazolium bis (trifluoromethane sulfonyl) imide (TFSI) ionic liquid monomer and mixed in an increasing range of wt.% with uralumina. The rheology and electrochemical activity of PGEs were highly dependent on the molar ratio of charged groups and copolymer content. Structure of the PGEs was studied by FTIR and Raman spectroscopy and a correlation between interactions polymer/uralumina and changes in speciation of uralumina was established. Despite the low molecular weight of the copolymers, the resulting polymer electrolytes develop elastomeric character associated with the binding ionic species. Although there is room to improve the electrochemical activity, in this study these new gels provide sufficient electroactivity to make them feasible alternatives as electrolytes in secondary aluminum batteries.