Uniaxial Tensile Creep Behavior of Epoxy-Based Polymer Using Molecular Simulation

Research on the Dynamic Characteristics of Perfluoroalkoxy Alkane Springs

Semiconductor cleaning system ultra-clean flow control pumps are critical equipment in the semiconductor industry. Among them, the perfluoroalkoxy alkane (PFA) spring is a pivotal component to control the pump, and its dynamic performance is crucial to ensure the efficient operation of the system. However, the dynamic performance of the spring is often affected by the operating frequency. This paper studied the effect of different working frequencies on the dynamic property of the spring through compression-cycle experiments under uniaxial sinusoidal excitation. The force-displacement curves under different compression frequencies were fitted to obtain the dynamic stiffness of the PFA spring under different cyclic loading frequencies. The variation in the spring's hysteresis coefficient was evaluated using the hysteresis curves of different cyclic loading conditions. After 2 million compression experiments, the changes in dynamic stiffness, hysteresis coefficient, and spring height were investigated. The obtained results revealed that, as the frequency increases, the dynamic stiffness of the spring increases. The hysteresis coefficient of the PFA spring is the largest at 10 Hz and the smallest at 6 Hz. Upon conducting 2 million compression tests, it was discovered that the dynamic stiffness experiences the greatest attenuation rate of 4.19% at a frequency of 8 Hz, whereas the hysteresis coefficient undergoes the largest attenuation of 42.1% at a frequency of 6 Hz. The results will help to improve the design and application level of PFA springs.

High Thermal Resistance of Epoxy/Cyanate Ester Hybrids Incorporating an Inorganic Double-Decker-Shaped Polyhedral Silsesquioxane Nanomaterial

In this study, we prepared a difunctionalized cyanate ester double-decker silsesquioxane (DDSQ-OCN) cage with a char yield and thermal decomposition temperature (T_d) which were both much higher than those of a typical bisphenol A dicyanate ester (BADCy, without the DDSQ cage) after thermal polymerization. Here, the inorganic DDSQ nanomaterial improved the thermal behavior through a nano-reinforcement effect. Blending the inorganic DDSQ-OCN cage into the epoxy resin improved its thermal and mechanical stabilities after the ring-opening polymerization of the epoxy units during thermal polymerization. The enhancement in the physical properties arose from the copolymerization of the epoxy and OCN units to form the organic/inorganic covalently bonded network structure, as well as the hydrogen bonding of the OH groups of the epoxy with the SiOSi moieties of the DDSQ units. For example, the epoxy/DDSQ-OCN = 1/1 hybrid, prepared without Cu(II)-acac as a catalyst, exhibited a glass transition temperature, thermal decomposition temperature (T_d), and char yield (166 °C, 427 °C, and 51.0 wt%, respectively) that were significantly higher than those obtained when applying typical organic curing agents in the epoxy resin. The addition of Cu(II)-acac into the epoxy/BADCy and epoxy/DDSQ-OCN hybrids decreased the thermal stability (as characterized by the values of T_d and the char yields) because the crosslinking density and post-hardening also decreased during thermal polymerization; nevertheless, it accelerated the thermal polymerization to a lower curing peak temperature, which is potentially useful for real applications as epoxy molding compounds.

Double-Decker-Shaped Polyhedral Silsesquioxanes Reinforced Epoxy/Bismaleimide Hybrids Featuring High Thermal Stability

In this study, we synthesized bismaleimide into a functionalized double-decker silsesquioxane (DDSQ) cage. This was achieved by hydrosilylation of DDSQ with nadic anhydride (ND), reacting it with excess p-phenylenediamine to obtain DDSQ-ND-NH₂, and treating with maleic anhydride (MA), which finally created a DDSQ-BMI cage structure. We observed that the thermal decomposition temperature (T_d) and char yield were both increased upon increasing the thermal polymerization temperature, and that these two values were both significantly higher than pure BMI without the DDSQ cage structure since the inorganic DDSQ nanoparticle could strongly enhance the thermal stability based on the nano-reinforcement effect. Based on FTIR, TGA, and DMA analyses, it was found that blending epoxy resin with the DDSQ-BMI cage to form epoxy/DDSQ-BMI hybrids could also enhance the thermal and mechanical properties of epoxy resin due to the organic/inorganic network formation created by the ring-opening polymerization of the epoxy group and the addition polymerization of the BMI group due to the combination of the inorganic DDSQ cage structure and hydrogen bonding effect. The epoxy/DDSQ-BMI = 1/1 hybrid system displayed high T_g value (188 °C), T_d value (397 °C), and char yield (40.4 wt%), which was much higher than that of the typical DGEBA type epoxy resin with various organic curing agents.

A Mixed Iteration Method to Determine the Linear Material Parameters in the Study of Creep Behavior of the Composites

This paper presents and applies a mixed iteration method to determine the nonlinear parameters of the material used to study a composite’s creep behavior. To describe the research framework, we made a synthetic presentation of the viscoelastic behavior of composite materials by applying classical models. Further, the presented method was based on a calculation algorithm and program, which was applied on several types of materials. In a consecutive procedure of experiments and calculations, we determined the material parameters of the studied materials. The method was further applied to two composite materials in which the nonlinearity factors at different temperatures were determined.