Preparation and Characterization of New Sol-Gel Hybrid Inulin-TEOS Adsorbent

Monolayer Adsorption of Ciprofloxacin on Magnetic Inulin/Mg-Zn-Al Layered Double Hydroxide: Advanced Interpretation of the Adsorption Process

In this study, magnetic inulin/Mg-Zn-Al layered double hydroxide (MILDH) was synthesized for the adsorption of ciprofloxacin. The application of various analytical techniques confirmed the successful formation of MILDH. For the optimization of controllable factors, Taguchi design was applied and optimum values were obtained as equilibrium time─100 min, adsorbent dose─20 mg, and ciprofloxacin concentration─30 mg/L. The highest capacity of the material was recorded as 196.19 mg/g at 298 K. Langmuir model (R2 = 0.9669-0.9832) fitted best as compared to the Freundlich model (R2 = 0.9588-0.9657), concluded the monolayer adsorption of ciprofloxacin on MILDH. Statistical physics model M 2 was found to fit best to measured data (R2 = 0.9982-0.9989), indicating that the binding of ciprofloxacin took place on two types of receptor sites (n1 and n2). The multidocking mechanism with horizontal position was suggested on the first receptor site (n1 < 1), while multimolecular adsorption of ciprofloxacin lying vertically on the second receptor site (n2 > 1) at all temperatures. The adsorption energies (E1 = 22.79-27.20 kJ/mol; E2 = 18.00-19.46 kJ/mol) illustrated that the adsorption of ciprofloxacin onto MILDH occurred through physical forces. Best fitting of the fractal-like pseudo-first-order kinetic model (R2 = 0.9982-0.9992) indicated that the adsorption of ciprofloxacin happened on the MILDH surface having different energies. X-ray photoelectron spectroscopy analysis further confirmed the adsorption mechanism of ciprofloxacin onto MILDH.

Fabrication of graphene oxide/inulin impregnated with ZnO nanoparticles for efficient removal of enrofloxacin from water: Taguchi-optimized experimental analysis

A novel nano-adsorbent zinc oxide impregnated graphene oxide/inulin (ZGI) was prepared for the investigation of the removal efficiency of enrofloxacin. Characterization of the nano-adsorbent was accomplished through Fourier transform Infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with EDS, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. The average crystallite size of nanomaterial (ZGI) calculated from XRD data was 14.82 nm. The adsorption of enrofloxacin onto ZGI was performed in batch mode. The variables of adsorption process such as adsorbent dose, pH, contact time and initial concentration of enrofloxacin were optimized by Taguchi method to achieve the maximum removal efficiency. The optimum values of variables were: adsorbent dose = 25 mg, pH = 7, contact time = 60 min and initial concentration = 50 mg/L. The maximum adsorption capacity and removal efficiency of the material for enrofloxacin were 317.83 mg/g and 98.60%, respectively at 303 K. Redlich-Peterson isotherm model was the best fitted among the various isotherm models based on highest R² values (0.9978-0.9981) and lowest χ² (3.43 ×10^-4-2.00×10^-3). Kinetic data followed pseudo-second order model (R² ≥ 0.9974) more accurately as compared to pseudo-first order model (R²≤0.9772). The adsorption mechanism was illustrated on the basis of XPS and Raman studies. Reusability investigation showed that the nano-adsorbent ZGI could be used up to 5 adsorption-desorption cycles with greater than 90% removal efficiency.

Anticorrosion Properties of a Novel Hybrid Sol-Gel Coating on Aluminum 3003 Alloy

In this study, a novel hybrid sol–gel coating on AA3003 substrate was developed and the effects of various waste material additives on the reinforcement of the sol–gel coating and the anticorrosion properties in the saline medium were investigated. Egg shell, crumb rubber, activated carbon obtained for pyrolysis of waste rubber tire, waste rubber tire, cement kiln dust, and ST100 additives were tested as reinforcement materials. The AFM characterization results of the coating formulations on AA3003 alloy revealed enhanced roughness values for the modified coatings as compared to the base coating. Similarly, no significant changes were detected in the Fourier transform infrared spectroscopy (FTIR) absorption peaks of the hybrid polymeric material upon loading it with the waste additives, while slight changes in the hydrophobic properties of the final modified coatings were observed as a result of the modification process. Electrochemical impedance spectroscopy (EIS) results revealed that the hybrid sol–gel coating had a promising potential for the protection of the AA3003 substrate against corrosion in the saline medium. However, the loaded additives negatively affected the corrosion resistance properties of the parent hybrid sol–gel coating. For instance, the egg shell additive had the least negative effect on the barrier properties, whereas the cured coating layer of the sample loaded with cement and clay additives showed some disintegration, inhomogeneity, and low barrier properties on the metal surface.