Preparation of Graphene Oxide/Cellulose Composites with Microcrystalline Cellulose Acid Hydrolysis Using the Waste Acids Generated by the Hummers Method of Graphene Oxide Synthesis

Synthesis of multi-layer graphene oxide from HCl-treated coke and Brazilian coals by sulfuric acid thermal exfoliation and ozone oxidation

This study involved the synthesis and characterization of graphene oxide (GO) from mineral coke and bituminous coal. HCl treated and non-HCl treated ultrafine powder obtained from both precursors were treated with H2SO4, followed by thermal treatment, and oxidation with ozone and ultra-sonication for GO production. The synthesized materials were characterized using Fourier transform infrared spectroscopy (FTIR), zeta potential (ZP), particle size distribution (PSD), transmission electron microscopy (TEM), X-ray diffraction (XRD) and Raman spectroscopy. The results confirmed the exfoliation of the material primarily at the edges of its structure and the formation of multilayer graphene oxide (GO) from mineral coke and bituminous coal. Furthermore, it was found that carbonaceous materials with graphitic morphology are easier to exfoliate and oxidize, leading to the production of higher quality graphene oxide. Therefore, the GO synthesized from mineral coke exhibited the best quality in this study. The methodology used proposes an innovative approach, offering a faster, more economical, and environmentally friendly synthesis compared to the traditional Hummers' method, thereby adding value to other raw materials that can be utilized in this process, such as Brazilian coke and coal.

Self-Assembled CNF/rGO/Tannin Composite: Study of the Physicochemical and Wound Healing Properties

In this study, a conductive composite material, based on graphene oxide (GO), nanocellulose (CNF), and tannins (TA) from pine bark, reduced using polydopamine (PDA), was developed for wound dressing. The amount of CNF and TA was varied in the composite material, and a complete characterization including SEM, FTIR, XRD, XPS, and TGA was performed. Additionally, the conductivity, mechanical properties, cytotoxicity, and in vitro wound healing of the materials were evaluated. A successful physical interaction between CNF, TA, and GO was achieved. Increasing CNF amount in the composite reduced the thermal properties, surface charge, and conductivity, but its strength, cytotoxicity, and wound healing performance were improved. The TA incorporation slightly reduced the cell viability and migration, which may be associated with the doses used and the extract's chemical composition. However, the in-vitro-obtained results demonstrated that these composite materials can be suitable for wound healing.

Cotton functionalized with polyethylene glycol and graphene oxide for dual thermoregulating and UV-protection applications

A thermoregulating smart textile based on phase change material (PCM) polyethylene glycol (PEG) was prepared by chemically grafting carboxyl-terminated PEG onto cotton. Further deposits of graphene oxide (GO) nanosheets were made on the PEG grafted cotton (PEG-g-Cotton) to improve the thermal conductivity of the fabric and to block harmful UV radiation. The GO-PEG-g-Cotton was characterized by Attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), Raman spectroscopy, X-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), and field emission-scanning electron microscopy (FE-SEM). With an enthalpy of 37 and 36 J/g, respectively, the DSC data revealed that the functionalized cotton's melting and crystallization maxima occurred at 58 °C and 40 °C, respectively. The thermogravimetric analysis (TGA) presented that GO-PEG-g-Cotton was thermally more stable in comparison to pure cotton. The thermal conductivity of PEG-g-Cotton increased to 0.52 W/m K after GO deposition, while pure cotton conductivity was measured as 0.045 W/m K. The improvement in the UV protection factor (UPF) of GO-PEG-g-Cotton was observed indicating excellent UV blocking. This temperature-regulating smart cotton offers a high thermal energy storage capability, better thermal conductivity, thermal stability, and excellent UV protection.

Development and Evaluation of Cellulose/Graphene-Oxide Based Composite for Removing Phenol from Aqueous Solutions

In this study, a graphene oxide/cellulose composite (GO-cellulose) was prepared usingcellulose and graphene oxide (GO) through ultrasonication, followed by the freeze-dried method. The Brunauer-Emmett-Teller (BET) specific surface area of GO-cellulose (~6.042 m²/g) was higher compared to cellulose (1.023 m²/g).The UV-Visible spectraindicated that the prepared GO-cellulose composite removedphenol efficiently from aqueous solutions with high adsorption power. The effectiveness of the composite for phenol adsorption was examinedunder diverse conditions.The results reveal that the composite optimally improved the adsorption at pH 7 with a dose of 0.125 g/30 L in about 40 min. The adsorption process showed that in optimum conditions, 86 ± 2% of phenol was removed in 40 min with an adsorption capacity of 6.192 mg g^-1. The adsorption behavior was well fitted to the pseudo-second-order kinetic model and the Langmuir isotherms at all temperatures.The present study suggests that synthesized GO-cellulose is useful inthe removal of phenol pollutants from aqueous solutions.

Improvement in Migration Resistance of Hydroxyl-Terminated Polybutadiene (HTPB) Liners by Using Graphene Barriers

The excessive migration of plasticizers leads to debonding and cracking of a liner, which can compromise the safety of a solid propellant. Graphene oxide (GO), with a laminar structure as a filler, can effectively reduce the migration of plasticizers. In this study, we modified GO using toluene diisocyanate (TDI). The cross-link density of the substrate was increased by grafting isocyanate groups to obtain a denser liner for the purpose of preventing plasticizer migration. We also used octadecylamine (ODA) to modify GO by grafting negatively charged amide groups on the GO surface. The electrostatic repulsive effect of the amide group on the plasticizer molecules was used to prevent plasticizer migration. Two modified GOs were filled into the hydroxyl-terminated polybutadiene to prepare two composite liners. We then investigated the migration resistance and migration kinetics of each modified liner using the dipping method. In addition, we explored the mechanical properties of each modified liner. Compared with the original liner, the anti-migration and mechanical properties of the modified composite liners were significantly improved. Among them, the TDI-modified liner had the most obvious improvement in migration resistance, while the ODA-modified liner had the greatest improvement in bonding properties. All types of liners met the requirements of the current propellant systems. This study provides an effective reference for improving the migration resistance and bonding properties of the composite liner.

Ultralight, Mechanically Enhanced, and Thermally Improved Graphene-Cellulose-Polyethyleneimine Aerogels for the Adsorption of Anionic and Cationic Dyes

Graphene-cellulose-polyethyleneimine aerogels (GA-MCC-PEI) were prepared using a simple, environmentally friendly method to remove anionic and cationic dyes in water. Graphene-cellulose hydrogels were prepared using a hydrothermal method and then immersed in a polyethyleneimine aqueous solution for 48 h to obtain graphene-cellulose-polyethyleneimine hydrogels, which were then freeze-dried. The light and porous composite aerogels had a good compression resistance, and the maximum allowable pressure of the graphene-cellulose-polyethyleneimine aerogel with a cellulose content of 43% was 21.76 kPa, which was 827 times its weight. Adsorption of the anionic dye amaranth and the cationic dye methylene blue by the graphene-cellulose-polyethyleneimine aerogel was satisfactorily modeled using the Langmuir isothermal equation, indicating monolayer adsorption. When the cellulose content was 39%, the equilibrium adsorption capacities of the composite aerogel for amaranth and methylene blue were 369.37 mg/g and 237.33 mg/g, respectively. This graphene-cellulose-polyethyleneimine aerogel can be used to remove dye pollutants in water to maintain ecological balance, thus broadening the application space of aerogel materials, that is, as adsorbents in different environments.