Imidazolium-Quaternized Poly(2,6-Dimethyl-1,4-Phenylene Oxide)/Zeolitic Imidazole Framework-8 Composite Membrane as Polymer Electrolyte for Fuel-Cell Application

Design and Utilization of a Direct Methanol Fuel Cell

This study introduces a step-by-step, summarized overview of direct methanol fuel cell (DMFC) fundamentals, thermodynamic-electrochemical principles, and system evaluation factors. In addition, a parametric investigation of a JENNY 600S DMFC is conducted to simulate cell performance behavior under varying operating conditions. The system is mathematically modeled and solved in MATLAB and accounts for multi-irreversibilities such as the activation and ohmic and concentration overpotentials. The performance of the modeled system was validated against theoretical and experimental results from the literature. The results indicated that increasing the fuel cell's operating temperature yields enhanced output cell voltages due to enhanced methanol oxidation reactions. Nevertheless, the maximum efficiency limits of the fuel cell tend to decrease with an increase in temperature. In addition, the model has also depicted that enhanced output cell voltages are associated with increased oxygen consumption, resulting in the lower exit flowrates of the reactants.

Recent Developments on Bioinspired Cellulose Containing Polymer Nanocomposite Cation and Anion Exchange Membranes for Fuel Cells (PEMFC and AFC)

Hydrogen fuel cell (FC) technologies are being worked on as a possible replacement for fossil fuels because they produce a lot of energy and do not pollute the air. In FC, ion-exchange membranes (IEMs) are the vital components for ion transport between two porous electrodes. However, the high production cost of commercialized membranes limits their benefits. Various research has focused on cellulose-based membranes such as IEM with high proton conductivity, and mechanical, chemical, and thermal stabilities to replace the high cost of synthetic polymer materials. In this review, we focus on and explain the recent progress (from 2018 to 2022) of cellulose-containing hybrid membranes as cation exchange membranes (CEM) and anion exchange membranes (AEM) for proton exchange membrane fuel cells (PEMFC) and alkaline fuel cells (AFC). In this account, we focused primarily on the effect of cellulose materials in various membranes on the functional properties of various polymer membranes. The development of hybrid membranes with cellulose for PEMFC and AFC has been classified based on the combination of other polymers and materials. For PEMFC, the sections are associated with cellulose with Nafion, polyaryletherketone, various polymeric materials, ionic liquid, inorganic fillers, and natural materials. Moreover, the cellulose-containing AEM for AFC has been summarized in detail. Furthermore, this review explains the significance of cellulose and cellulose derivative-modified membranes during fuel cell performance. Notably, this review shows the vital information needed to improve the ion exchange membrane in PEMFC and AFC technologies.

Development of WO3-Nafion Based Membranes for Enabling Higher Water Retention at Low Humidity and Enhancing PEMFC Performance at Intermediate Temperature Operation

The proton exchange membrane (PEM) represents a pivotal material and a key challenge in developing fuel cell science and hydrogen technology. Nafion is the most promising polymer which will lead to its commercialisation. Hybrid membranes of nanosized tungsten oxide (WO₃) and Nafion were fabricated, characterised, and tested in a single cell. The incorporation of 10 wt% WO₃ resulted in 21% higher water uptake, 11.7% lower swelling ratio, almost doubling the hydration degree, and 13% higher mechanical stability of the hybrid membrane compared to the Nafion XL. Compared to commercial Nafion XL, the rNF-WO-10 hybrid membrane showed an 8.8% and 20% increase in current density of the cell at 0.4 V operating at 80 and 95 °C with 1.89 and 2.29 A/cm², respectively. The maximum power density has increased by 9% (0.76 W/cm²) and 19.9% (0.922 W/cm²) when operating at the same temperatures compared to the commercial Nafion XL membrane. Generally, considering the particular structure of Nafion XL, our Nafion-based membrane with 10 wt% WO₃ (rNF-WO-10) is a suitable PEM with a comparable performance at different operating conditions.