Influence of Content in D Isomer and Incorporation of SBA-15 Silica on the Crystallization Ability and Mechanical Properties in PLLA Based Materials

Antimicrobial Activity and Crystallization Features in Bio-Based Composites of PLLA and MCM-41 Particles Either Pristine or Functionalized with Confined Ag Nanowires

Composites based on an L-rich poly(lactic acid) (PLLA) and MCM-41, either neat or modified with a silver (MCM-41@Ag), are achieved by solvent casting, being next processed by compression molding. Ag is mainly embedded as nanowires within the hybrid MCM-41@Ag particles, enabling its antimicrobial character. In these composites, the PLLA thermal stability, nucleation efficiency, and mechanical response are dependent on the MCM-41 nature and, to a lesser extent, on its content. Thus, differences in transitions of the PLLA matrix are noticed during cooling at 10 °C/min and in the subsequent heating when composites with neat or modified MCM-41 are compared. A very remarkable nucleation effect is played by pristine MCM-41, being inferior when MCM-41@Ag is incorporated into the PLLA. Wide angle X-ray scattering (WAXS) measurements using synchrotron radiation and performed under variable-temperature conditions in the composites containing MCM-41@Ag indicate that during cold crystallization, the disordered α' polymorph is initially formed, but it rapidly transforms into ordered α crystals. A long spacing peak, clearly seen in pure PLLA, appears as a small shoulder in PLLAMCM@Ag4 and is undetectable in PLLAMCM@Ag9 and PLLAMCM@Ag20. Furthermore, an increase in MH with the silica content is found in the two sets of composites, the higher MH values being observed in the family of PLLA and MCM-41@Ag. Finally, remarkable antimicrobial features are noticeable in the composites with MCM-41@Ag since this modified silica transfers its biocidal characteristics into the PLLA composites.

Polymerization of Allyltrimethylisilane and 4-Methyl-1-Pentene by Using Metallocene Catalysts

Polymers of higher olefin, obtained by Ziegler-type polymerization, have been used in some critical fields, e.g., as the membrane for extracorporeal membrane oxygenation (ECMO), which plays an important role in the treatment of patients with severe COVID-19. The polymer obtained by a single-site catalyst, e.g., metallocene catalysts, demonstrated a higher performance. The homo- and co-polymerization of allyltrimethylisilane (ATMS) and 4-methyl-1-pentene (4M1P) were conducted using syndiospecific (cat 1) and isospecific (cat 2) metallocene catalysts. Cat 1 showed low conversions and provided a polymer with a higher molecular weight, while cat 2 behaved oppositely. ¹³C-NMR spectra certified the stereotacticity of the resultant polymer, and the resonance of the carbon atom of CH₂ (αα') between the two tertiary carbon atoms of the ATMS and 4M1P units were observed. This could be the evidence of the formation of a true copolymer. The crystallization of the polymer was explored using a differential scanning calorimeter (DSC) and wide angle X-ray diffraction (WAXD). All homopolymers and some of the copolymers showed high melting temperatures and low melting enthalpies. The WAXD patterns of the syndiotactic polymer and isotactic homopolymer or the ATMS-rich copolymer were consistent with the reported literature, but the isotactic 4M1P-rich copolymer provided the crystal form I, which is unusual for a 4M1P polymer without any pretreatment.

Combined Effects from Dual Incorporation of ATBC as Plasticizer and Mesoporous MCM-41 as Nucleating Agent on the PLA Isothermal Crystallization in Environmentally-Friendly Ternary Composite Systems

Different materials, based on an L-rich polylactide (PLA) as matrix, acetyl tri-n-butyl citrate (ATBC) as plasticizer, and mesoporous Mobile Crystalline Material.41 (MCM-41) particles as nucleating agent, were attained by melt extrusion. These materials are constituted by (a) binary blends of PLA and ATBC with different contents of the latest; (b) a dual compound of PLA and a given amount of MCM-41 silica (5 wt.%); and (c) ternary composites that include PLA, ATBC at several compositions and mesoporous MCM-41 at 5 wt.%. Influence of the incorporation of the plasticizer and nucleating particles has been comprehensively analyzed on the different phase transitions: glass transition, cold crystallization, melt crystallization and melting processes. Presence of both additives moves down the temperature at which PLA phase transitions take place, while allowing the PLA crystallization from the melt at 10 °C/min in the composites. This tridimensional ordering is not noticeable in the pristine PLA matrix and, accordingly, PLA crystallization rate is considerably increased under dynamic conditions and also after isothermal crystallization from either the melt or the glassy state. An important synergistic effect of dual action of ATBC and MCM-41 has been, therefore, found.

Graphene Nanoplatelets-Based Textured Polymeric Fibrous Fabrics for the Next-Generation Devices

Graphene is a 2D crystal composed of carbon atoms in a hexagonal arrangement. From their isolation, graphene nanoplatelets (nCD) have revolutionized material science due to their unique properties, and, nowadays, there are countless applications, including drug delivery, biosensors, energy storage, and tissue engineering. Within this work, nCD were combined with PLA, a widely used and clinically relevant thermoplastic polymer, to produce advanced composite texturized electrospun fabric for the next-generation devices. The electrospinning manufacturing process was set-up by virtue of a proper characterization of the composite raw material and its solution. From the morphological point of view, the nCD addition permitted the reduction of the fiber diameter while the texture allowed more aligned fibers. After that, mechanical features of fabrics were tested at RT and upon heating (40 °C, 69 °C), showing the reinforcement action of nCD mainly in the texturized mats at 40 °C. Finally, mats' degradation in simulated physiological fluid was minimal up to 30 d, even if composite mats revealed excellent fluid-handling capability. Moreover, no toxic impurities and degradation products were pointed out during the incubation. This work gains insight on the effects of the combination of composite carbon-based material and texturized fibers to reach highly performing fabrics.